Having problems with your Psi Blue Max 2200 High Pressure Gas Power Washer ?

PULL CORD TO HARD TO PULL FOR A POWER WASHER

\015 PULL CORD TO HARD TO PULL FOR A CRAFTMAN POWER WASHER WHAT TO DO?\015

Answers :

Repair Help & Product Troubleshooting for Psi Blue Max 2200 High Pressure Gas Power Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Briggs and Stratton power washer Quantumpower 5hp water driver series 1750 PSI 2.0 gal min model # WGV1721 . I got it used and it was always a bit hard to start but always started. Pull cord frayed and broke I bought new cord and a neighbor replaced for me. Now it does not want to do anything when pulled. I can't get top cover off that has screws with round holes instead of phillips or standard slots to get to pull cord winding


Spray well with WD-40 or similar, and take a small chisel, on it's edge, and hit hard enough to allow chisel to dig in to head of screw, making a "V" like slot in the head, then angle chisel slightly and start tapping in direction of loosening(counte ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

PULL CORD TO HARD TO PULL FOR A POWER WASHER


... Psi Blue Max 2200 High Pressure Gas Power Washer

Hard to pull cord - Dewalt Heavy-Duty 3100 PSI 6.5 HP Gas-Powered Pressure Washer DP3100


... Dewalt Heavy-Duty 3100 PSI 6.5 HP Gas-Powered Pressure Washer DP3100

My neighbor just gave me a Troy Bilt 020207 power washer. It is 2450 PSI and 2 GPM. He snapped the pull cord rope. I looked at the pull cord cover and it seems to have 3 rivets holding it to the main housing. How do you recommend to repair or replace the pull cord?


Sounds like a briggs engine, DONT remove the rivits, go down a little further and remove the 4 3/8 bolts that hold the blower housing on.Turn it upside down, prewinf the pulley in the direction that it turns when the rope is being pulled. When it sto ... Briggs & Stratton Pressure Washers

Very Hard to Pull Cord to start engine on Northstar Pressure Washer. When I remove spark-plug it is very easy to pull cord. With plug reinserted it is extremely difficult to pull cord to start engine.


On the Honda motors very hard pull starting with no start ck for broken rocker on exhaust or intake, I've already repaired two with this problem...... ... Northstar Pressure Washer 3000 PSI

Just bought a john deere 3300 power washer. It started with no problem. shut it off to answer the phone. When I went to start it the pull cord wouln't pull tryed everything but still the pull cord was in a locked position. Don't know what to do hoping you have an answer for me


First turn off the water to the machine. pull the trigger to release any trapped pressure in the high pressure hose, then try to start the machine. if it starts then turn on the water to the machine.it may be that the engine is tryi ... Pressure Washers

Pull cord won't pull out on my power washer - Honda Maxus Pressure Washer MX5222


... Honda Maxus Pressure Washer MX5222

I purchased a Honda Power Washer Model PWH2600 two weeks ago. I cleaned half my deck when the motor shut off unexpectantly, and now the cord will not pull to restart the engine. Any ideas what I can do for the cord to pull normally?


You just bought it so it is under warranty. I would take it back to the place you bought it for service. If the starter rope will not pull then the engine may be locked up. Check the oil level and make sure it is full before returning it for service. ... Honda Pressure Washers

My Honda 2600 psi power washer will not pull to start. It was running great then I allowed the neighbor to borrow it. He ran the washer till it was out of gas and proceeded to refuel and at this point it would no longer start. The pull cord is out about 4-6 inches out and I am concerned about taking the casing off myself. Fearing that it may throw more off on the unit. If i take the casing off are there any spring loaded parts that will dismount? What should I do? Spark Plug? Turn


You should be fine to take the recoil off, there shouldn't be anything that shoots out at you. You might want to check the oil level on the engine, many of the Honda engines won't start unless there is enough oil in them. If your oil level is fine, c ... Honda Pressure Washer PSI 3000

Karcher power washer starter cord cannot pull


... Pressure Washers

Hard starting 6hp Briggs and Stratton power washer engine. I poured a teaspoon of gas into the cylinder; reinserted the spark plug and with one pull in ran fine. This is a choke start engine and it may take 12 to 15 pulls to start on a cold engine. The unit is clean. The air cleaner is new. The spark plug is new. The unit is 2 years old with very little use.


Hello. I have this same machine. Go to the auto parts store and get an aerosol can of starter fluid. Have a helper squirt some into the air intake while you start it. Then continue to squirt a little starter fluid as it runs for the first two mi ... Campbell Hausfeld Pressure Washers

My pull cord to my pressure washer is hard to pull and it's not starting. Why? This all started after I tried to start it without the water on while attempting to start.


Take out the spark plug and trying pulling it , if its still tight then you may have seized your pump ) , put a rag over te spark plug hole as there may be fuel/oil mix in the cylinder , check the oil in the engine , check the oil in the pump ( look ... Pressure Washers

I have the Troy built 020337 power washer and can't even pull the cord


... Briggs & Stratton Pressure Washers

Honda gcv160 pressure washer won't turn over. pull cord just starts to move then STOPS hard.


... Honda Pressure Washer PSI 3000

I can't start my 6.5hp b s power washer. choke on, in run mode , pulling cord won't start


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Power Washer will not start - pull cord seems to be stuck


Hi take out the bolts holding the compleat pull starter remove unit pull the cord if it wont move something is jamming it inside if it is ok then the fault is with the motor //seized or washer remove washer pump if engine turns over /pump seized ... Honda Maxus Pressure Washer MX5222

Pull cord stuck Briggs&Stratton Power Washer


... Briggs & Stratton 2200 PSI Gas Pressure Washer

Unable to pull starting cord on toro power washer


... Pressure Washers

My gas power washer will not start. I filled the gas, checked the oil, set the choke, made sure it was on, changed the spark plug, checked the air filter, and drained any water. When I pull the cord to start I don't even get a putter. Anything else I can try or do I need to take it to a service place.


Will it run if you pour a small amount of gas in the carb? If so, it's a fuel supply problem. Most likely a stuck closed float needle. ... Honda Maxus Pressure Washer MX5222

I have Honda pressure washer.Inorder to start the pressure washer you have to pull the cord. THe cord is stuck and I am not able to pull the cord. Why it and what should I do to start the washer.


... Honda 2500 PSI Gas Pressure Washer

So I found this power washer for sale. The seller claims that the washer generates a good stream of water, not just full power. He also mentions that after a few minutes the engine starts to bog down like it is working extra hard. Does this sound like a pump issue? Could something be clogged or would the pump need to be replaced? Or should I avoid this power washer?


Don't buy a power that doesn't work.There are many expensive parts on a power washer. If it was cheap and simple to fix, the seller would fix it and the washer would not be for sale.Would you buy a car that doesn't work? Especially ... Pressure Washers

Power cord pulled out of machine


... Viking VDB325SS Dishwasher

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

I have a Frigidaire 4000 Series Dishwasher, Model# FDB4315FCO, almost six years old. It acts as if there is no power. There is no error code. If I pull the power cord I get a "PF" message.


... Dishwashers

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1022 seconds