Having problems with your Psi Blue Max 2200 High Pressure Gas Power Washer ?

I need the 1/8 in. one way valve that allows the soap to mix with the spray.


Answers :

I've had good luck getting parts from rental centers. Since they have to repair what they rent, a lot of times they have the small parts at the shop. good luck.
Repair Help & Product Troubleshooting for Psi Blue Max 2200 High Pressure Gas Power Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need the 1/8 in. one way valve that allows the soap to mix with the spray.


I've had good luck getting parts from rental centers. Since they have to repair what they rent, a lot of times they have the small parts at the shop. good luck. ... Psi Blue Max 2200 High Pressure Gas Power Washer

Poor washing The soap door opens but soap still in there after wash cycle. We got lower spray arm off and one plastic piece but can't get all the way to the pump. Pump appears to possibly be cracked so we suspect it needs replacing, but we can't get it out.


Before you suspect the pump and motor assy, do you hang the silverware basket on the front side of the lower rack or if not did one of the holders for the rack fall off and you replaced it? I have found that id the basket is hung on the rack that tal ... Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

Low Pressure with no hose attached, pressure is good, attach hose without wand and pressure drops 50%. Have had pump apart 10 times, have checked bypass valve, have even removed bypass and filled passage way so water could not bypass wihout any change. Am down to thinking pump casting is cracked allowing bypassing to happen. Does each of the three piston chambers have a check valve so one piston is not pumping back into another piston chamber?


I worked at a tool rental while attending college and had the opportunity to work on a variety of pressure washers, however, they were of the commercial type. Commercial washers are slightly different in that they usually have seperated components fo ... Karcher 2500 PSI Pressure Washer

The dishes are left with a soapy film and there is soap left draing down the inside of the door. Basically the wash or rinse cycles are not working correctly. Like water is not spraying the way it needs to be.


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Dishwashers

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

I need the small valve that the soap pick up hose attaches to for a Honda 6.5hpGX200; 2800psi and the end of the spray nozzle


... Honda Pressure Washer PSI 3000

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

I do need the igniter for the burnner / my igniter i think it is the wrong one , it is too shot and the spray of oil do not fire/ i think the 'plugs' is little short to ignite on the spray , comes on and off / but i have sparks all times, only dos not get fire , do i need longer plugs !!!do go under the noze of spray!!


Send me a email at [email protected] I am an dealer for Northstar and many other brands of pressure washers. I need the model number off the machine if you have it. I can get you th ... Northstar Gas - Powered Wet Steam & Hot Water Pressure Washer 2700 Psi, 2.5 Gpm

After running one load in my new Maytag dishwasher everything came out coated and the glasses were stained. I called for a service person who told me it was the soap I was using. He said that I need to get soap with phosphates but I can[t find any. Was he telling me the truth and if so, what brand do I buy? All the ones in the store are phosphate free.


Hi,I think he is blowing smoke...well..you know where...I would try a few different detergents before giving up on it. Some will work better with your water then others...also try different rinse aids..Keep experim ... Maytag MDB7100AWB Dishwasher

GE Nautilus My dishwasher is approx. 6 years old. It has recently started having this problem. On the second cycle (the one where the little door inside opens and release the soap) does not want to work right. The door will open, but it is like there is no water spraying to spread it out. The soap (I've tried both liquid and powder) sticks and drys, running down the door and in the bottom of the tray. I have to open the machine and add the soap to the bottom of the machine if I want to get my di


Smoking from GE (Model:gsd3725f00bb) dishwasherWe moved in an old house, the dishwasher had been installed. but today we found smoking from the dishwasher and smells burned plastic. Could you have any resolution for me? or this problem is popul ... GE Nautilus 24" Built-in Dishwasher

Whirlpool Quiet Wash Plus dishwasher Model DU920PFGZ3. Worked fine until I replaced the insinkerator and forgot to punch the drain plug leaving water standing on the bottom of the machine. I punched the drain opening, and pushed the cancel/drain cycle button. It drained fine but since no water comes from the spray arms. I have removed the arm all the way down..NOTHING!! Some research indicated it could be the water inlet valve. When the buttons are pushed, it cycles but no spray or water.


... Dishwashers

Soap dispenser need to know where the soap dispenser is all i see is a trough that says detergent on one side and the othe side is a dispenser which manual online says its for a rinseing agent


There is a screw cap on the back wall of the dishwasher,unscrew the cap and place your rinse agent in there.I groove on the door is for your dishwasher powder ... Equator 20 in. CD 400 Compact Dishwasher

SGV55M43EU - The machine does not spray the water even if the pump works. The only way to have the water spray is to add water manually directly inside the machine. I checked the inlet valve (acqua-stop) , it seems to work. many thanks, Alessandro


... Dishwashers

My dishwasher spray arms were clogged with calcium buildup so I cleaned one and replaced the other. I also removed the fixed disc-shaped device underneath the lower spray arm and found the particle filter was clogged- so I cleaned it out. The dishwasher ran fine for a few times but then the filter clogged again, and again, and again. Now I need to make a routine of disassembling the parts to get at the filter every week because the filter no longer clears itself during the wash and/or emptying c


You may want to check your hot water tank. It may need drained and cleaned, Or you may have the rod in the tank disintegrating. Also check you water faucet areators to see if they have calcium pieces too. ... Maytag Dishwashers

My Kitchen Aid KUDS01FLSS2 dishwasher does not spray water thru the wash arms nor do they seem to turn. Additionally, one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" when rotated by hand. The spray arm assembly appears true on visual examination. The unit fills, cycles and pumps out in an apparent normal way. While on this site a while back I was advised to clean the unit and referred to a downloadable repair manual that was, in fact, not


Hi.The fact that "one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" would suggest a tubing problem. However there are more faults that will result in no spray. Testing in this case can be ... KitchenAid Dishwashers

I have a go kart with a honda power washer motor that I just purchased.It lacks power at start and stalls alot.Put new pull in,sprayed carb cleaner,adjusted carb,new air filter,need to know if it need a fuel pump and were to get one


Hondas are gravity feed no pump needed .You might need to clean the card though. ... Karcher 2500 PSI Pressure Washer

Hi, I have a SMEG slimline dishwasher (model UKSTX4-1), and need to repalce the lower spray arm support duct. I was wondering how to remove the existing one? Do you need to access a locking nut from underneath?


I believe on this model there is a locking tab near where it mounts down to the pump area,check for a tab under the arm that feeds the wash arm ... Smeg 18 in. DWF410SS Slim-Line Free-standing Dishwasher

Need to clean out the upper spray arm and so would like to remove it (like I did the lower one) and clean it out. Help!


We have a PDW7800J01WW that I removed all the arms on recently.There is a single hex-head screw that acts as the pivot at the center of the top most arm. Just remove this screw to remove the spray arm.Be very gentle reinstalling it thoug ... GE 24 in. Profile PDW7800 Built-in Dishwasher

GE Dishwasher detergent dispenser has hardened soap in it when cycle is done We, too, have the same problem. Ours is a GE Profile MAX - GSD6610K01CC. The basket is obviously not allowing the door to open fully, so I think it is intended to work this way. The question remains, though, why is there solidified powder remaining in the dishwasher after the complete dishwasher cycle has finished? Tabs work well, as the tab falls out, but all the powder doesn't seem to. Electrosol powder is less expen


... Dishwashers

I have a B&S 3.75, model 98902,type 014301,code 96032254 gas engine which powers a 1500PSI Clean Master power washer. The engine will start if primed but will not continue to run unless fuel is sprayed down the throat of the carburator.Apparently a gumedup/dirty carb. what is the best way to proceed to clean it? Where is best place to get a rebuild kit and/or replacement carb if needed? What are other possibilities if not a dirty carb?


... Pressure Washers

The dishwasher doesn't seem to have nearly enough water in it. The upper sprayer arm doesn't seem to be spinning when running (I open the door and look really quick) and the lower one looks like it barely spins and barely sprays water. The dishes are barely wet and the soap is just laying on the bottom. The water is on, there are no kinks in the supply line. It sounds like it is running, and pumps pumping, but being brand new I am not sure what it should sound like. It certainly doesn't sound li


I would lift the drain pipe higher. approx. 1/2 the height of the dishwasher . also rechack incomming water supply. Make sure no blockages and the like. Try again. ... Bosch Dishwashers

I have an lg ldf7811st and the bottom arm will not turn. I purchased the part 1267558 (motor assembly, vario spray valve) to repair it and I need instructions on how to install this part. Please advise.


You need to uninstall dishwasher and tip it backwards on the bottom of the dishwasher you will see a square panle remove the 2 screwsand replace the part then proceed in revers to put together ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

Hiya i have a titan-pro 3600 psi and i need to buy an unloader valve cap and a 15 m pressure hose, ive already tried the main supplier for the last month and they have not been able to help me, were else could i get one from?


The number to ring pressureparts from UK is 001-800-999-2245 \015\012\015\012Hope this helps. Please remember to rate this answer. Many Thanks. ... Pressure Washers

Leaks water from under dishwasher, some one suggested the fill valve assembly needs replacing???? kenmore


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If your\015\012dishwasher leaks, check these:\015\012\015\012 ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1332 seconds