Having problems with your Psi Blue Max 2200 High Pressure Gas Power Washer ?

A gas power waher 3500 psi ,with a honda gx390..Start proper but after 15 minutes turn off by it self.How i solve this problem??


Answers :

Hi there aldao62367
\012

\012 if the oil level is at correct level , check that the tank breather in the fuel cap is clear
\012then change the oil it may be thinning out , and low oil sensor float is not floating and makes the unit think its got a low oil problem - shuts down, also check for a tight valve ?
\012 off the top of head valve clearance for inlet 0.005 thou and ex 0.007 thou
\012
\012change oil to a 20w/50 or 10w/ 40 oil
\012
\012should hold about 1.0 litre
\012
\012cheers pauly46
Repair Help & Product Troubleshooting for Psi Blue Max 2200 High Pressure Gas Power Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

A gas power waher 3500 psi ,with a honda gx390..Start proper but after 15 minutes turn off by it self.How i solve this problem??


Hi there aldao62367\012 \012 if the oil level is at correct level , check that the tank breather in the fuel cap is clear \012then change the oil it may be thinning out , and low oil sensor float is not floating and ma ... Psi Blue Max 2200 High Pressure Gas Power Washer

Hi threr I have the following problem with my Haier DW12-EFM dishwasher: The dishwasher seems to operate properly for the first several minutes untill program selector knob stops betwin position 2 and 3. After I turn it manually it keeps on turning and than it stops again after I turn it again it operates till the end of the program but the dishes are not clean enough to be used. I also noticed that the heater does not operate (water is cold). Do you know wht the problem might be. Reg


... Haier 24 in. ESD100 Built-in Dishwasher

We have had a problem with our dishwasher since "winterizing" it to close the cottage for the winter. We were told to run it for a few minutes with antifreeze in it and then turn off and let it overwinter with the antifreeze in it. Now the machine leaves everything coated with a white film, even though we have a water softener and use jetdry. How can we fix this and is this the proper way to winterize our dishwasher if we close down our cottage and turn off the heat for the winter?


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

My Jackson CJ 20 is heating the water all the time, it stops after washing the dishes for 10-15 min and does nothing and after that i have to switch it off and turn it on again to wait another 10 minutes to heat the water and pray that it'll work. How can I solve this problem?


... Jackson Dishwashers

Model#lds5811bb--started making noise coming from the water inlet area(bottom left). 3/4's of the way through the cycle, noise became louder and then an error code "le" came on. We tried turning breaker off, then we tried in the rinse only cycle, but 5 minutes into it the "le" code error came on again. I'm fairly handy, so I'm not sure what part I can replace to maybe solve the problem. I can't afford to spend a couple of hundred dollars for a repair man to fix it. I'll appreciate any suggestion


The LE code is a locked motor code. Something may have gotten into the pump impeller. I would take the screens and filters off and clean the and check the pump for something stuck in it. It could also be the motor going bad but I would check the obvi ... LG Dishwashers

My dishwasher also gets stuck at 1 minute and it keeps on going and going . I had to turn it off. I called up bosch and they told me to hold the power and the rinse and hold button for 5 seconds but it did not solve the problem - now i have to go through the exopense of bringing in a technicien do you have any solutions???


Well basicly the technicien came and knew nothing - he tried a few things so he is alreadyto change the electric board and we all know how expensive that is - any way he left saying he will come back today with a new board  - after he left i wen ... Bosch 24 in. SHU5305UC Built-in Dishwasher

Child Lock light glows without pressing Energy Saver Dry button for four seconds. Cannot turn off by pressing Engery Saver Dry button for four seconds. Turning off main power and turning back on doesn't solve problem. But turning off main power for extented period, over night, and turning back on does fix proble for a very short period but Child Lock does come back on by itself. Is replacing the Console Assembly the only fix? Is there some button sequence to disable Child Lock altogher?


The mini manual for this dishwasher is located behind the kick plate. The mini-manual reveals that the child lock (called a control lock in the manual) can be disengaged by pressing and holding the air dry button for four seconds.or ene ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Dishwasher is just less than 1 year old. it doesn't respond to attempts to turn on. I turned off the power at the box and back on after 10 minutes. it worked. then the same problem returned. now it wont turn on at all. I checked all the connections I could and they seem fine. I know it is getting power. My guess is that something is wrong with the computer system. any ideas?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Maytag 24 in. MDBH950AW Built-in Dishwasher

Dishwasher sounds as if it starts cycle, then stops, bleeps, and Fat and prewash lights come on. Manual says to turn off machine, turn off tap, wait 30 seconds and turn it all back on, but it doesn't make any difference. Manual says 'If the above does not solve the problem, check that the water feed pipe is not blocked' however, it doesn't say where this is, or how to do it. Please help!


Hi.You need to check the water inlet hose, that is the hose connected to house water faucet at the back of the dishwasher.Checck for blockage in the hose and ensure that the inlet hose is not blocked or kinked.If t ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Meiko ecostar 530f dishwasher My problem is the 2nd green light starts turning to orange and then turns off completely, meaning the washing cycle takes over 10 minutes. Then eventually both lights turn off. Is there an easy solution or is it a programming issue? Thanks in advance


... Dishwashers

Dishwasher (Model # SHU6806UC), unit is about 8 years old, very light use, less than once a month, and no previous problems. Turned on unit and after about 10 minutes, I found water on floor coming from dishwasher. Turned unit off and turned off water shut-off valve. Removed dishwasher from cabinet. Found mice had chewed a hole in water discharge hose under unit, inspected all hoses, and found another hole chewed in the 13" flex hose in the front of the unit. Also found the float chewed to alm


Hi,\015\012 Check the valve is open where the supply gets its water from the sink supply.There is a garden hose type swivel adapter after the valve, Close the valve tightly and then unscrew that hose coupling and see if the hose is full of w ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

Kenmore Elite 13133K started to fill, the door was opened. Now it won't resume, drain or fill, the geen light is flashing. I turned the power supply off for 5 minutes and the problem still exists.


... Dishwashers

I have a Viking dishwasher made by Asko. It is less than 6 months old. Today I had a problem with my disposal (water not draining through it and leaking under the sink) and ran the dishwasher, which cleaned/dried the dishes fine. BUT, since the water was not properly draining from the disposal, apparently the dishwasher was not draining properly either. A repairman came to fix the disposal before I knew about the dishwasher issue. Now, the dishwasher won't turn off "draining mode" - button pu


... Viking DFUD042 Built-in Dishwasher

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

My serial #TH24050632 has an occational control board failure and requires a reset. That is my current problem. In the past I turned of the circuit breaker for thirty minutes, and then pressed sertain control buttons inseries or at the same time for ten to twenty seconds. I have misplaced the information I wrote down to correct my problem. Can you help me with the correct procedure to reset my control panel? Thank you.


Check if this works.\015\012\015\012Press normal wash and heated dry one after the other about 5 times.All lights on panel will light.Wait until all lights go out and it resets itself.It will go into a mode on it's own.Then press cancel a ... Dishwashers

The "clean light" on our Kitchenaid KUDIO1FLSS flashes 7 times and I cannot clear the problem to allow the unit to operate. Is there a sequence, using the control buttons, to permit the unit to run a system check? I disconnected the power for 30 minutes but that did not solve the problem.


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Maytag diswasher MDB6600AWW Sprayer arms don't spin. Dishwasher makes all the right noises, except for spraying. Water fills properly and heats up. Water drains properly. Found paper on the back of access panel. Ran Manual Function and Field Service tests, no problems indicated. Disassembled all the pieces inside the bottom of the dishwasher. No obviously damaged parts. Shaft for motor turns freely. It seems like the parts that attach from the impeller to the motor shaft don't


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Hi, I have a 3 year old Nemo F&P dishwasher which turns itself on and off for about 3 seconds each on/off continually.Eventually it does get enough water to wash but never goes into the wash cycle properly, ie the water just sits at the bottom. We dont think it's water pressure and it was working fine until recently.Could it be an electrical problem with the signal to fill properly not getting through? Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing ... Fisher and Paykel Dishwashers

Hello all, We have an Ikea Whirlpool DWF 416 that is a couple of years old and has never caused any problems. From today the door has stopped shutting properly. The electronics and internal mechanisms seem to be working fine, since when you turn it on the cycle starts - but only if you hold the door shut. Has maybe a catch gone? Any ideas for fixing a door-shutting problem like this? Thanks in advance! Dave


The catch is no longer working. Contact IKEA for the replacement part. I'm sure it's available through EBAY or something, but probably not guaranteed or as reliable. ... Dishwashers

I have a Kenmore dishwasher model # 665.13742k601, when the dishwasher is turned on to the normal wash cycle it will wash for abour 5 minutes. After the five minutes ''Delay 4'' and ''Cancel/Drain'' indicator lights will light up. What is the problem?


Kenmore has a near the same diagnosis as that of maytag when it comes to washers.you may refer to the link below.http://servicetechhelp.com/discus/messages/2801/6_917071_A_English-MD87100AWW-users-51306.pdf ... Kenmore Dishwashers

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Intermitttent beeping on bottom drawer of dish washer no error code only cycle to work all the way through is rinse cycle. Have turned off power supply over night did not fix problem. When you press pause button restarts for about five minutes then beeps again. No problem with top drawer. All inside cleaned using correct powder and rinse aid.


Panel control board Call Encompass Parts 1-800-638-3328 ... Fisher Dishwashers

I have Whirlpool dishwasher about 3years old it is the ADP7966 AAA 6th sense. When I put it on and turn the temperature knob, only the first temperature green light comes on althou I can turn the knob all the way round none of the other lights come on, my rinse aid and salt programmes light up thou ,and when I press the start button it flashes twice stops a bit then flashes twice again, and thats all it keeps doing. I would be very grateful if you help to solve the problem. Many thanks to you.


... Dishwashers

My Maytag Dishwasher MDBH750AWW will not turn on. Pressing the key pad on the top front does not activate the controls. I traced the wiring and found it is active in the door latch assembly, which I recently replaced. Question: 1) If I purchase a new Control Panel exterior white key pad, which is linked to the interior Control Board, should that solve the problem? Or,2) if I purchase a new exterior Control Panel finger touch pad, and an interior Control Board, will that solve the proble


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1207 seconds