Having problems with your Ridgid Rd80903 3000 PSI 2.6 GPM 5.7 HP Subaru Sp170 OHC Gas Powere ?

Starts but wont stay running

\015 Starts but cuts out about a minute later\015

Answers :

Hi ace
\015\012Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible.
Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
\015\012Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
\015\012Note:Before you disassemble the carburetor:
Write down on a piece of paper and or take a picture of how the linkage attaches to your carburetor for later reference when you go to reinstall your carburetor.
Mark each piece with a awl, or some kind of sharp instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.
That way you will know which way it goes back together when you reassemble it.
\015\012Sometimes you can get by with priming the carburetor or by using a very small shot of starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.
Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.
Check you fuel line/s condition...after a while they will degrade and need replacement.
\015\012Check/Clean/Replace your fuel filter if you have one.
When you remove your fuel lines from the carburetor be sure to make a drawing or take a picture of how the lines are connected to the carburetor.
Also a good time to take a picture for later reference for reassembly.
\015\012If the mower is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.
The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
\015\012When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.
Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.
Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.
Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.
Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.
When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.
But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.
Be sure to mark the turns down on a piece of paper.
That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.
Once you have your carburetor cleaned/rebuilt that should solve your problem.
Please take time to rate me
Bud
Repair Help & Product Troubleshooting for Ridgid Rd80903 3000 PSI 2.6 GPM 5.7 HP Subaru Sp170 OHC Gas Powere

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Stored for a year. i changed the spark plug and the fuel. i also cleaned the carb. water runs through the pump. but it wont stay running. it wants to start but only runs for a few seconds. i think it might be a fuel flow problem but im not sure.


Sounds like the float my be partially stuck closed. It allows enough fuel to run a few seconds then the engine uses it faster than the float lets the fuel back in. I would remove the float bowl and flip the float up and down a few times to make sure ... Honda Pressure Washer PSI 3000

Electrolux dishwasher all lights blinking and wont turn on push start button either all lights flash or normal light stays on  either case the dishwasher wont run a cycle


Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be goo ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Starts but wont stay running


Hi ace\015\012Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.\015\012N ... Ridgid Rd80903 3000 PSI 2.6 GPM 5.7 HP Subaru Sp170 OHC Gas Powere

Kenmore 665 17033400 Elite dishwasher clean light flashes 7 times and it wont run. i used the reset combination, all lights lit and stayed lit until i pressed reset. Then it started a wash. now the wash seems to be finished, though i am not sure and the clean light is flashing 7 times, pause, 7 times, etc.


That signals an issue with a faulty heater &/or heater drive circuit.(that info comes from their troubleshooting guide)I ran into it this weekend and discovered that the heater coil in the bottom of the washer was broken. ... Kenmore 24 in. 17032 Built-in Dishwasher

Maytag dishwasher lights but wont run, I can select a cycle then press start and nothing. also the control panel lights stay on when the door is opened


... Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher

My 5.5 honda engine on my lawnmower will start but wont stay running already cleaned the carb out didnt help there is no restrictions in the fuel lines im lost please help


It sounds like a fuel problem.\015\012first drian fuel out of tank.\015\012i know you have already cleaned the carby but dis assemble carby and clean with carby cleaner.\015\012re assemble carby & fill tank with fresh fuel.\01 ... Honda Pressure Washers

Honda 2700 psi GC160 pressure washer will start with starter fluid in carburetor but wont stay running? Changed sparkplug cleaned carburetor, Added fuel cleaner then let set and drained all fuelandadded new. Seems as if their is no fuel going from the tank to the carburetor?


... Pressure Washers

I have a problem with my karcher 2500 pressure washer with honda engine it will not start or stay running. I have used starting fluid to start it it starts but won't stay running.


Carb is mostly likely gummed up and should be cleaned. Best option is to dismantle the carb and soak in solvent or equivelant for a couple hours and replace it. Our use Gum Out. Do make sure you have a good spark plug and a strong spark. If you have ... Karcher 2500 PSI Pressure Washer

Honda CU2400 1-MHC has been sitting in my parents garage for about 2 years. It was used once or twice. It looks new. I tried to start it and it wouldn't. I drained the gas and put new premium gas in it and it started but it won't stay running and the pressure is not what it should be. It doesn't clean as well as the electric one I used last time. So, my problem is, it won't stay running and when it is running it doesn't have enough pressure. Any ideas???


After sitting that long, I'd guess the carburetor linkages etc., are partially seized and the governor is not operating as it should to allow proper RPM's when under load. Real good chance carburetor is gummed up good too. I'd get carb serviced, but ... Pressure Washers

I have a Whirlpool GU2275XTVY0 when I start the cycle on normal it will run for about 5 minutes then the power button starts flashing and wont run. It drains fine and starts fine just wont finish the cycle.


It might help if the wash arm had started moving when it shut off.\015\012\015\012Unless it is always exactly 5 minutes I would say perhaps the door switch is out of alignment. It might start ok when you engaged at time of closing door bu ... Whirlpool Gold GU2275XTV Builtin Dishwasher

My pressure washer let out blue smoke then quit. Wont stay running. What could it be?


... Honda Pressure Washer PSI 3000

Troy bilt pressure washer 2350 psi wont stay running after use


... Pressure Washers

Hi. Got a dishwasher from IKEA - Whirlpool DWH B00. It wont run anymore, 2 years old. It just wont start up, it starts to give a beep, and the solution is to press the <|> button for 2 sec, then restart it. But it still wont start. I've cleaned all filters, checked for water on board underneath, and given it some salt - no luck. Any ideas?


... Whirlpool Dishwashers

My lawn mower with a Briggs motor Wont start, has spark fuel is good , the unit is approx 5 years old, but seldom used, worked great last year, drained the fuel, and stored it for the winter.Refueled it and wont start. I can getting started if I pour a little gas down the carb, but naturally it wont run long. I'm thinking needle and seat, any help would be appreciated. Thanks


... Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

Troy bilt pressure washer 2350 psi wont stay running after use


... Pressure Washers

Engine wont stay running


It is a diaphram carb. Doe's the primer **** straight gas or does it have air bubbles in it? If it has bubbles in it then it is a leak in the fuel line.\015\012If not then Unhook the intake fuel line and pump the bulb until all of the gas is ... Briggs & Stratton Power Products 1539 Pressure Washer

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

DISHWASHER WONT GO INTO WASH CYCLES,WHEN I PUSH START GOES CANCEL/DRAIN,CAN HERE PUMP RUNNING THEN IT WILL TURN OFF,THERE IS NO WATER IN THE BOTTOM,SEEMS LIKE STUCK IN DRAIN CYCLE


... Whirlpool GU2300XTS 24 in Builtin Dishwasher

I have a Honda 5.5 hp pressure washer and it wont keep running I bought it off craigs list they said the last time it ran was almost a year ago I took off the carb and sprayed carb cleaner threwout but didn make a difference I cant seem to see any jets juist the float needle and that was clean if I pour gas in the carb it will run for a for about 5 seconds and but wont stay even if I choike it. does anyone have a answer


Try soaking the carb for 15 minutes in gasoline. If you have a plugged port just sparying may not be enough to clean it ... Honda 2500 PSI Gas Pressure Washer

13 hp honda pressure washer 3000 psi 4gal/min Hard to start and dies out after 20 seconds after the engine gets hot and running after multiple starts the engine will stay running but then dies every 30 minutes


There are a couple of things that can cause this problem. The first thing to check is if you are loosing spark. Dying after it gets hot sounds like to stater is failing in the engine. If you loose spark this is more than likely the issue. If you are ... Honda Landa PG 3500 PSI Pressure Washer

Pressure washer will not stay running. Have put in new fuel, new plug, new oil. Will not start until I spray some ether in carb, then it will start and run for about 3 seconds, then stall. will not restart without another shot of ether. What should I try next? thanks


... Briggs & Stratton Gas Pressure Washer 20244

Honda motor wont stay running ,carb not getting enough gas to stay running


As it is gravity fed you would need to remove thfuel line from the carby to check that the fuel is geting to that point,if not removanf clean fuel .bowl and filter . if ok. then a carby service is in order ,they are not difficult but you do need comp ... Pressure Washers

I HAVE A NEW CRAFTSMAN PRESSURE WASHER WITH KEY START. I HAVE USED IT ONCE AND WHEN I TRIED TO START IT IT WAS HARD TO START HAD TO PULL START IT. NOW IT WONT START. LET PRESSURE OUT HAVE HOSE OH AND RUNNING, NEW SPARK PLUG HAS OIL, GAS FILTER FINE.HAS GOOD COMPRESSION, BUT WILL NOT FIRE GET SOME RECOIL. GETTING GAS TO SPARK PLUG AND GETTING SPARK. IM LOST PLEASE HELP.


... Pressure Washers

With Kitchaid dishwasher KUDS01FL, it wont run. All control buttons seem to work (by lighting up when pressed) except "start". When press "start", it doesn't blink or start. Does this indicate a bad start button switch or something else? Is this something I can replace? Thanks.


Hi Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...-high temp wash - ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My briggs and stratton lawnmower will start but not stay running


... Brute 7800821 22-Inch 190cc Briggs And Stratton 625 Series Gas Powered FWD Self Propelled Lawn Mower
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1209 seconds