Having problems with your RTO 1800 PSI Pressure Washer ?

PWER WASHER RUNS PERFECT, WHEN WATER COMES ON, IT STALLS. BUT IF YOU PULL TRIGGER BACK ON WAND, THEN SPRAYER WORKS. THE MINUTE YOU LET GO OF TRIGGER, IT STALLS OUT.


Answers :

Hi you have got a fault with the unloader it's not unloading so its going a bove the 13amps and knocking the thermol overload out or blowing a fuse you could cable tie the trigger open or get a new unloader kit costing about £70.00 regards
Repair Help & Product Troubleshooting for RTO 1800 PSI Pressure Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

PWER WASHER RUNS PERFECT, WHEN WATER COMES ON, IT STALLS. BUT IF YOU PULL TRIGGER BACK ON WAND, THEN SPRAYER WORKS. THE MINUTE YOU LET GO OF TRIGGER, IT STALLS OUT.


Hi you have got a fault with the unloader it's not unloading so its going a bove the 13amps and knocking the thermol overload out or blowing a fuse you could cable tie the trigger open or get a new unloader kit costing about £70.00 regards ... RTO 1800 PSI Pressure Washer

Presure relief value not working when let off trigger on wand


Sounds exactly like the problem and the soluition you are looking for. ... Karcher 2500 PSI Pressure Washer

I HAVE A BRAND NEW TROY-BUILT 2600PSI pressure washer. I have used it twice for about 1/2 hour each time. It worked perfectly. I tried to use it today with everything hooked up perfectly. The Honda engine started perfectly; how ever when I squeezed the wand trigger, the engine instantley died. I let the engine warm up and slowley pushed the choke in. I let it warm up for plenty of time; but everry time I squeezed the trigger it instantly quit- it even backfired once before dying. I changed the g


Sounds like the governor is stuck. My pressure washer speeds up when it has to pump. Don't know if yours uses vacuum to trigger governor or direct linkage. Good Luck. ... Psi Blue Max 2200 High Pressure Gas Power Washer

Surging and stalling When just started, the pressure won't rise with the wand. When the trigger is applied for long periods of time (1 minute) the engine stalls


Thought it was a free advice web site? Scammin' scumbags!!! ... Honda Pressure Washers

I have a craftsman 4.5hp quantum xte pressure washer 1800psi/4.5hp/2.0gpm mod 580.761800. I have to start the washer before I turn the water on and just today started with if I let go of the trigger on the wand the washer stalls. Can you advise as to what the problem is and how to solve? Thanks ****


The pressure relief valve(bypass) is most likely stuck or clogged. take the relief valve off and check for broken or jammed parts..there should be a bypass hose that goes around the pressure valve ... Briggs & Stratton Pressure Washers

I have a HD 2701 DR pressure washer that starts and runs fine and usually works fine the "first" time but if you let go of the trigger and then try to use it again you just get a trickle out of the end of the wand. Usually if you hold the thing open for a while it will kick in (sometimes it takes forever...). Any ideas? It sounds like some of the "unloader valve" problems are similar but I do not see an "unloader valve" in the parts lists for the 2701...


... Karcher G 3050 OHR Gas Pressure Washer

Let go of wand trigger pressure will not come back


Spill valve is stuck and needs to be cleaned and greased common problem....also check all connections for blockage in line ... Karcher 2500 PSI Pressure Washer

If while pressure washing I let off the wand trigger it looses pressure and I have to turn of the washer motor and wait for the pressure to return.(seems like some kind of vapor lock problem)When the pressure returns I hold the trigger and restart the washer. If I let off the trigger we go through the same process again. this is a g3050


Hi and welcome to FixYa, I am Kelly. \015\012 This is most often caused by the bypass / un-loader valve located on the high pressure output side of the pump. The valve will either have a stem type valve with a knurle ... Karcher 2500 PSI Pressure Washer

At the beginning the pressure washer was running but there was no power from the nozzle. I stop the gun trigger, remove the nozzle , it works for 1 minute and stop working again Now the washher pressure turns off on its own after 1 minute or less Honda 2400 psi


See attached link:\015\012http://www.wmpcs.com/index.php?main_page=page&id=14\015\012\015\012If you continue to have the problem you m ... Honda Karcher G2400HH-R Pressure Washer

Kranzle 160t pressure washer works but full pressure drops off I then release the pressure trigger for a while and it will work at full pressure again for half a minute.


... Pressure Washers

My pressure washer will not start or stay running unless the trigger is open on the wand. The engine runs good until the trigger is released then the engine stalls instantly. what is worng and how do I fix?


... Briggs & Stratton 2200 PSI Gas Pressure Washer

Unit Runs fine, except when you press the spay gun the engine stalls out. Unit was working fine, ran out of gas, filled tank and started engine. Engine was running fine, triggered spray gun and the engine stalls out.


... Pressure Washers

See below Hi, Disconnect the Power Supply for Few Minutes, say 10 minutes and then Turn it ON. Do you see any Error Message on the Display? Do you see any Other Light Blinking? Have you tried to Press Cancel / Any other Button on the Touch Pad? Is it Working? Do you hear any Beep? Let me know, if needed further assistance. Hope i helped you. Thanks for using ' Fixya ' and have a nice day!! Comments: Apr 02, 2010 - Thanks for your response!! One more detail, i wanted to ask - Is that Wash Li


What's going on here? ... Dishwashers

Siemens SE25A266GB/22 Hi My dishwasher programmer doesnt work, when i try to put the time in it will not let me go further thah 20 minutes or so, then if you run that time it sticks on 'one minute to go'. on opening nothing has been cleaned.


HelloWelcome.You said, Hi My dishwasher programmer doesnt work, when i try to put the time in\015\012it will not let me go further thah 20 minutes or so, then if you run\015\012that time it sticks on 'one minute to go'. on opening n ... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

Pulsating motor, turn machine on pull trigger, it works but not very good, let trigger off, and motor pulsates quite rapid


... Pressure Washers

Karcher 3100 pressure washer, motor runs fine but when I squeeze the trigger on handle, high pressure pump won't come on unless I remove tip and water is coming out of wand without restriction. Help anyone have any ideas? It did come on once but when I let go of trigger it wouldn't come back on.


... Alfred Karcher Quick Connect Nozzles 2600 3100 Psi 5 Pack

My powerwasher(2500psi) with a B&S QUANTUM 120000 gas motor will stall when hot, pressure drops significantly, and is hard to restart. When it does re-start, it stalls again in 2 minutes. This behavior started recently after working fine for 2 days. I changed the oil-no difference.


I assume you did plug and filter change. Check the plug wire for fire when hot or problem occurs; it should be pretty visible- don't shoch yourself. Check that fuel is reaching carb, check tank for debris. You may need to have valve adjusted. G ... Pressure Washers

My karcher pressure washer is switching on and off when the wand is not being used. the pressure should hold but it appears to cut in and out every 2 secs. the machine works o.k. when pulling the wand trigger but i think the pressure is slightly reduced.


Unfortunately these little units have this problem commonly, 9 times out of 10 it will be the plastic head on the unit will be cracked and leaking slightly... it builds up pressure then leaks out and tries to build up the pressure again ... Karcher K2.26 Electric Power Washer

DeVilbiss Pressure WAsher EXH2425 Honda engine GC160qha pump DAPC axcial cam. When using washer sprayer both the engine and pump seem to operate normally. As soon as I let off the trigger of sprayer the engine dies. Help?


Hi and welcome to FixYa. I am Kelly \015\012Take a look at your engine parts manual here: \015\012\015\012 ... Pressure Washers

TRIGGER WAND ON PRESSURE WASHER WILL NOT WORK . IT WAS VERY HARD IN THE BEGINNING AND NOW WILL NOT WORK AT ALL


... Honda Pressure Washer PSI 3000

I have the Karcher 2400 psi, 5.0 Honda engine. Starts fine, but when you pull the handle on the spray wand, the pump does not kick in and the water just continues to trickle out of the end of the wand at regular faucet pressure. Occasionally the "clutch" will kick in and you have full pressure, but if it does and I let off of the trigger then chances are that it won't kick in again. has been getting worse for several years.


... Karcher 2500 PSI Pressure Washer

My pressure washer doesn't start/work when I attach my wand to the trigger. It works fine when I take it off, but there is no pressure, just normal water coming out. I'm thinking I may need a replacement wand?


... McCulloch FH160G Pressure Washer

I have a Honda GC160 motor on a powerwasher. The engine stalls when I release the power wand handle, but if i keep the handle squeezed, it works but the engine sounds like it is laboring.


... Honda Pressure Washers

Pressure washer sputters and stalls when trigger is engaged


Hi k2times01It is a always a good idea to clean out the gas tank and use new fuel, however, this sounds like an RPM problem. Try adjusting the RPM up a tad and see if it runs better when you load it. If the RPM isn't the problem, you may have ... Pressure Washers

The control panel on my dishwasher will not work. I have tried the unlock button and that was not the problem...I have turned off power to it for 2 minutes and that was of no help either...Can someone please let me know what is going on with my dishwasher....


Your touch pad control panel has gone bad. The part alone is about $150. not counting a house call and labor. If this machine is over three years old I recommend replacing it. A repair without a warranty is not cost effective. Joe ... Whirlpool DU930PWS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0765 seconds