Having problems with your Samsung Dishwashers ?

My Samsung DMT800 series dishwasher has had the main control board replaced under warranty three times since I've had it. The problem: The unit won't activate via the touch buttons until I pull the plug for a second and "re-boot" the device. It then works for a few days or a week and fails again. The last board was replaced two weeks ago and it has failed only once. I'm waiting for it to fail again before I call Sears home services again. Has anyone else had this issue? My repair man has said y


Answers :

Repair Help & Product Troubleshooting for Samsung Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Samsung DMT800 series dishwasher has had the main control board replaced under warranty three times since I've had it. The problem: The unit won't activate via the touch buttons until I pull the plug for a second and "re-boot" the device. It then works for a few days or a week and fails again. The last board was replaced two weeks ago and it has failed only once. I'm waiting for it to fail again before I call Sears home services again. Has anyone else had this issue? My repair man has said y


... Samsung Dishwashers

My Kitchenaid dishwasher (model KUDS02SRSS0) keeps burning out my dispenser. First I replaced the dispenser, then I replaced the control board and dispenser, it worked for two weeks and now I have a melted solenoid again in my dispenser. I've measured voltage to the solenoid and it is getting 110V through the entire diagnostic cycle. This is wrong. It should only get power at some point during the cycle to open the dispenser. It appears the control board has failed again and in the same wa


HI. The relay that controls the voltage and timed release command, via logic chip, is indeed damaged(stuck on). This is a common theme with this particular design. The original control board was recently replaced with a substitution model ... KitchenAid 24 in. KUDP01DLBS Free-standing Dishwasher

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

Our Maytag model MDB4010AWW (8 1/2 years old) is leaving food stuck on the dishes and glasses on the top rack consistently. We've run several bottles of Dishwasher Magic through in the past few weeks which has only helped the problem a little. We posted this question to a similar forum a few weeks ago, and it was suggested that the wash pump might need replacement. What's the average life expectancy of a lowend dishwasher like ours? would it be more cost effective to replace it rather than to sp


It would cost you at least the 200.00 to have it replaced since the pump cost 150.00 and you would have labor added. It should last longer than it did if that's what's wrong with it. I would first observe to see if the upper spray arm is spinning and ... Dishwashers

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

Water is not flowing into the dishwasher and as a consequence it overheats. In the couple of weeks prior we noticed unusual noises and taking longer to complete washing. Also since about two weeks ago dishes have had white mineral deposits and film on glasses. I suspect that the water pump is not working. I cannot find the salesslip from sears to see when we purchased the machine but I sus pect it was about 6 years ago. We are debating wther to have a service call, possibly including replac


Hi,\012Here is a tip that will help you to find out why water will not come into thedishwasher... Dishwasher Trouble No Water entering Dishwasher ... Kenmore 24 in. 16262 Built-in Dishwasher

I have a kitchen aid dishwasher model number KUD101TJBLO. I have had the thermal fuse replaced numerous times. It may run two weeks ir it may rub two cycles then the fuse blows. My serviceman has given up on finding a solution.He has replaced the control board and the door switch. However it continues blowing the fuse. I read on the internet that you need to replace the entire wiring kit that comes with the fuse but my repairman says this will not fix the problem and refused to replace the kit.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please check for the short on the wires near the heating element. Also check the resistance of the heating element, it should not be more than 1.6 K ohms. Also ma ... KitchenAid Dishwashers

Lights are on, but dishwasher will not start. Called a local repairman. He decided the control board failed. he ordered a new board and replaced it. Now he says the new board is defective. I think otherwise


That model has an electronic thermal fuse that clips onto the control board housing. the dishwasher will not start if that fuse is blown. you can check it if you have a meter. If it has continuity through it, its good, if no continuity, replace it. T ... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

I have Whirlpool control board part #8267371. The problem is that the dishwasher does not complete a cycle. A green light on the door will flash. From what I understand it indicates a failure in the heater at some point. I replaced the heater and all I am left with now is the possibility that the control board has failed. So my question is this. Are there common problems associated with these boards ? Which components should I be looking at ? I don't have a schematic. Or is there anyone that can


Yeah, I'm in the middle of that, too. There's a thermal fuse you can check with a meter just above the control panel inside the front door. It should be 0 ohms. Then it's the control board, I guess. Looking for the same one myself right now. I'm goin ... Kenmore 24 in. 16032 Built-in Dishwasher

I have a Bosch Dishwasher SHU5302. A year ago it just kept on running. I ran a diagnostic test and replaced the circuit board that had a burn spot. The unit washed after that but would not drain wa


... Dishwashers

I have a Kitchen Aid dishwasher that ha had the processing board replaced twice in the last year. It is not functioning again so this will be the third time in 13 months. Any reasons why the board keeps failing?


Do you live in an area that has a lot of power outages? That could be one reason. Another reason is an area that has power surges. You can have an electrician add a surge protector to your electric fuse box that will help. Otherwise, if a good techni ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

MY SUPERBRA D/W JUST BLEW THE FUSEABLE LINK AFTER BEING REPLACED OVER SIX WEEKS AGO..REPLACED THE LINK AND D/W WORKED FINE..NOW HAS BLOWN AGAIN WITH NO VISIBALE ISSUES THAT WOULD CAUSE IT..ANYONE HAVE AN IDEA WHAT WOULD CAUSE THIS?


Plenty of ideas !!! 1st, if the voltage to the unit is too low or the size of the electric line is too long or too thin, then the electric will raise the current to try to compensate for the lack of voltage, and the fuse only knows or senses when th ... Dishwashers

SHU 5316 UC dishwasher by bosch. I think it is from about 1998 or 99. It blew a circuit breaker yesterday. I reset the circuit braker, but it won't even power on. It may have burned something out. We replaced the control board 2 years ago. Please tell us: 1. Is it worth fixing again, or just replace? 2. Any suggestios? Maybe the pump has shorted? THANKS SO MUCH!! Mark


Hi Mark -There's no internal fuse in this dishwasher, so if there's no power you may well be looking at a new control unit and probably another major component as well, depending on what caused the overload or short. The most likely ... Bosch SHU5316UC Dishwasher

Bimetal fuse The incoming power was blinking off and on due to a storm, it caused the bi metal fuse to fail in the dishwasher when it was not operating, the fuse was replaced with kit #w10258275, now two weeks later the fuse has failed again while operating.These fuses are expensive, I would like to know the value (amps) of these fuses so that the system can checked to try and find out the reason for failure, or maybe you might have an idea where to start. Thanks Tad


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Maytag dishwasher #33323190JG Many of the dishes come out with a white-ish coating. I usually end up using an SOS pad to scrub it off. Three weeks ago a repair man replaced the heating element due to the recall but that didn't help it. He suggested trying "Dishwasher Magic." I've used Dishwasher Magic a couple of times within the last two weeks but the problem remains


Hi,\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... \012Bought new spray arms online and installed them in minut ... Maytag Dishwashers

My dishwasher has no power. A service tech came a few months ago and replaced the mother board along with a fuse. Am I having a short and need to replace the fuse? If so,where and how would I do that?


... KitchenAid KUDM01TJBS Dishwasher

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Hi I have the Kitchenaid dishwasher KUDIO1FLSS2 and all the buttons work except the two most important ones, the heavy and normal cycle. I had a service person out about 6 mo. ago and he said the control panel was about to go bad and replaced a fuse. He ended up coming again a week later and replacing the fuse with a stronger fuse. Now it's acting up again and I'm sick of hand washing dishes and don't feel like handing over another $300 or more if I can do it myself or maybe I just need to buy a


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Recently replaced the control board for Electrolux EIDW6105GW1; after nearly a month of working w/o any problems this evening the machine made it through the wash cycle and then stopped working (all lights on wash cycle door menu are flashing). Took kick plate off bottom to check control board and the leak dectector is lit. I can see no leaks in front and am reluctant to do anything else with this POS. I spent nearly $1000 on this 18 months ago and have already sunk over $300 into a new contr


... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Whirlpool-Gold GU2500XTPT6 - Quiet Partner III (3-1/2 years old) - Electronic Fuse has blown; I replaced it and one week later it failed again. Any tips on next steps?


... Whirlpool Dishwashers

I have a Bosch SGS46E22GB Exxcel dishwasher. It is failing to drain or pump out dirty water. About a year ago we had this fault and the engineer replaced the impeller jug. He showed my wife how to clear a blockage with the left hand side panel removed. I can't get the panle off so am looking for instructions on how to remove it. Thanks


... Dishwashers

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

Dishwasher will not start when pressing the start button. Timer light flashed numbers and went off. None of the lights and buttons work. Circuit breaker in electrical panel is working. Does the on/off switch need replacing, or is it possible a mini circuit board is bad? Dishwasher installed in 2000 and is used on the average once per week.


As it is nearly 10 years old i would suggest you replacing the circuit board. To test exactly we would need the help of an continuity tester and multimeter. ... Bosch 24 in. SHU53 Built-in Dishwasher

Replaced heating element and board. Worked for a week and now won't run. Wash light illuminate for about a minute, then goes out.


May need pump motor assembly or a thermosttat/fuse if u replaced those already i think thats whuts left ... KitchenAid Dishwashers

My Kenmore Diswasher (Mod # 665.17842400) has crapped out again. Towards the end of a cycle, the power seems to have been lost. There is now water in the bottom, and the user interface won't come on. 2 months ago I replaced the user interface and the magical board it connects to to solve a start button problem. I checked the power coming to the washer and it is live.


There is a thermal fuse on the control board. It protects in a overheating problem or sometimes when there are to many appliances on the same circuit that creates a high amp draw, that melts the fuse not actually blowing it like a short. Check your d ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0505 seconds