Having problems with your Samsung DMR77LHS Tall Tub Dishwasher ?

No reponse from the power button. I have checked the breaker and the power connection to the dishwasher. It appeers to have not finished the last cycle wather still in the tub.


Answers :

Not sure if you have got a user manual for your dishwasher.
\015\012
\015\012A few things to check - was there any code displayed on the front display at the last cycle.
\015\012
\015\012To get the water out have you tried the Cancel operation (press Heavy and Delicate buttons together for 3-4 secs)
\015\012
\015\012It is also possible the child lock might be on. Press Rinse and Quick buttons together for 4-5 secs
\015\012
\015\012If power button is not responding and the Display is blank then it is likely the power to the controller has been lost. Have you checked for any fuses at the base (behind the foot board) of the dishwasher? Make sure the mains power is turned off when you are accessing the dishwasher.
Repair Help & Product Troubleshooting for Samsung DMR77LHS Tall Tub Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No reponse from the power button. I have checked the breaker and the power connection to the dishwasher. It appeers to have not finished the last cycle wather still in the tub.


Not sure if you have got a user manual for your dishwasher.\015\012\015\012A few things to check - was there any code display ... Samsung DMR77LHS Tall Tub Dishwasher

The dishwasher stop during the wash cycle. It did finish draining the water from the tub. The machine is not showing a power signs, I check the circuit breaker and the fuse is not tripped. I open and closed the door and the door latch seems to be working fine. There is just no power to the washer. Usually when a machine breaks down, there still is power or buttons that light up on the front of the machine. I looked on the internet and many say that the fuse could be tripped. No where can I find


... Whirlpool DU912 Dishwasher

I have no power to the dishwasher. I tried the circuit breaker, flipped it. No lights on, nothing. It must have been running when the power might have gone off, may be the power surged or something and it wasn't able to finish running the cycle. I have taken out all my dishes and washed them by hand but I still have water standing in the bottom of the dishwasher. I am a mechanically challenged mom and my husband won't be getting home for two more weeks. The dishwasher is a WhirlPool Gold Quiet


First check and make sure that the units not on a switched receptacle(and is wired into this circuit(i know the dishwasher is "hard-wired",as in the unit doesn't have a plug on it,but it could have been wired into this switched circuit by mistake) un ... Whirlpool Dishwashers

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

The dishwasher did not finish last rinse cycle. I have no power, no lights light up. I reset the breaker. Is their another reset button on the Dishwasher itself. I have a Quiet3 Power GE Dishwahser.


Hi,I am sorry to hear regarding the trouble.The best way to reset - Disconnect the power supply for few minutes, say 15 minutes and then turn it on.If the problem persists, this would confirm an internal failure.As ... GE Dishwashers

My dishwasher often finishes its cycle and there is still water in the bottom of the tub. it seems like some timer/cycle is out of sync. because if i start a new cycle it seems to finish draining first before starting to wash again. is there an easy way to reset this?


Sorry to read about your problem, I hope this helps you out.you have a clogged pump,hose or sump areaI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Have the Fisher & Paykel single drawer dishwasher ds 603 and put it on a normal cycle last night. It started as per normal and sometime during its cycle it stopped and the drawer now seems locked. The power doesn't work at all now and tried turning it off at the power point - still no response.


It is very likely the thermal fuse has blown or the power supply board has had it. Either way the power to the controller and the drawer lid seal motors is cut off. This is why the drawer is in locked state as the motors have seized.\015\012 ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

During power scrub cycle which is the one we use most of the time the dishwasher stays at one minute fot a long time. the dishes come out clean and it finally does finish cycle just dont know why it takes so long on last minute of cycle for so long


It's just heating the water more ... Bosch 24 in. SHU43 Built-in Dishwasher

Last night when the dishwasher reached 6 in the cycle (plate warming) there was a loud pop that caused as to loose all electricity in our home. When the electrician took the dishwasher out of the powerpoint the electricity came back on. The power point still works so the electrician has said that the dishwasher has blown. Does this sound like something that could be fixed? And if so who would I contact to do this? Thanks


The heating element in a dishwasher ( 120 volts only on a residential dishwasher ) draws a lot of current like an oven element (240 volts ) & probably has shorted or split open to let water into the internal element(from the outer shell/cover) of the ... Dishwashers

Dishwasher model GLD5500L00WW finished last cycle normally. Now, no response when buttons are pushed. Lights were on above buttons but have since have gone out. There is power to the dishwasher. Dishwasher is 3 years old and used daily.


... Hotpoint Dishwashers

No power the dishwasher didnt finish its last cycle and now there is no power at all


... Whirlpool 24 in. DP940PWP Free-standing Dishwasher

After my dishwasher finished a cycle yesterday the drainage pump kept running even whilst open, tried swiching power off, both on the dishwasher and main 'gpo'. swiched back on but still no good?


... Asko 24 in. D3112 Free-Standing Dishwasher

Fisher paykel dishwasher dd601I runs complete normal cycle and finishes normally. 2-3 sec. after completion the washer motor srarts to run and the f1 fault (flood sw. activated) is dislayed. When the power button is pushed the fault spontaneously disappears and the motor stops. no moisture is in thre bottom under the tub and the normal cycle can be ru again with the same results.


Hi\015\012\015\012F1 code indicates an overfill condition which may cause when dishwasher can’t pump out dirty water due to a plugged drain hose.\015\012open dishwasher fully ,dry up as much water as possible the ... Dishwashers

I have a Whirlpool dishwasher, model DU943 that's under 7 years old. I went to use it last night and it won't power on. I tried selecting all of the cycles, but the dishwasher never came on. I looked through the troubleshooting tips in my manual (like checking the circuit breaker for a tripped fuse, which was fine) and I still have a problem. what else can I try? thanks.


Hello- This unit has a thermal fuse inside the door panel on the control. This part is replaceable. If it is bad, replace.- and would suggest not using heated dry as this is most common cause of fuse failure. Let me know if this info helps- have more ... Whirlpool Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

New dishwasher (Beko 2542F slimline model). Put it on for 1st time last night -when I got up this morning, the cycle which should have taken just over 2 hours hadn't finished. There's soapy water in the bottom of the machine which hasn't drained and the "wash" light is still on. Looks like the dishes are clean but hasn't moved onto the rinse/dry part. Followed instruction in manual to drain it (hold start stop button till lights flash and should drain in 45 sec) but nothing happened.


... Beko Dishwashers

Its a whirlpool dishwasher washed dishes last night dishes were clean but rinse water was still in the tub now no lights come on the touch controls its like its dead, i checked power and got it to the circut board but dont know how to check any thing else


Hi.... you have a Bi-metal bad .. It has opened You can by-pass it by using one wire and I bet it lights up ... dont leave it by-pass..... The bi-metal is right on the main board ... Dishwashers

After the dishwasher is finished running they cycle the machine is still humming - there is power on -- only way to turn it off is to turn off the circuit breaker


... Asko D1776 Stainless Steel Built-in Dishwasher

Dishwasher does not turn on at all - no lights when power button is pressed. There is an inch of water in the bottom - the last cycle probably didn't finish but we did not notice when we unloaded it.


... Bosch SHU5315UC Dishwasher

My AEG Oko Favorit 50750 VI built-in dishwasher has been unpredictable for a few weeks - sometimes leaving things dirty although I've run cleaning programmes and replaced the filter basket thingy - but today I have a power light on but no other lights - no programme lights and no 'end' light either. Not sure if it finished the last cycle or not. Desperate not to replace as cash is tight - is there anything obvious I might check please? Thanks..


Hi\015\012\015\012Most probably the door catch switch or the on off button is bad.\015\012Please check the link bellow..\015\012\015\012 ... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

My Kenmore dishwasher Model #36315672 is not draiing properly. When it's finished a cycle, there is still a lot of water on the bottom of the tub. What should I do?


There is a one way flapper valve broken off that could be lodged in the pump outlet. You have to remove the pump to repalce it. ... Kenmore Dishwashers

My 3-yr old GE Profile dishwasher lost power soon after initiating wash cycle. Checked braker switch...fine. Checked outlet power...fine. Dishwasher power mysteriously came back on approximately 12 hours later. Initiated another wash cycle and lost power again after a few minutes. Water remains in bottom of tub. What's wrong????


First thing i would check is the actual wiring behind the toes kick\015\012you will seea wire box, shut the breaker off, open up the box and double check all your connections there,\015\012 the next step would be to check the voltage ac ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

I have a kenmore ultra wash mod# 665.13492k600 dishwasher that in the last couple of days will not drain the last cycle . If you push the cancel /Drain button after the cycle is finished it will then drain but all the dishes have soap spots on them and are very wet .I have checked for clogs but cant find any I have also run a lot of water throug our waste disposla because the dishwasher drains into it help ??


... Kenmore Dishwashers

When I start the cycle the lights on the panel turn off as if to indicate the power is off, but the dishwasher is still running with no water being dispersed. I let the cycle run through, but the dishwasher is still filthy afterwards. (not cleaning at all) What colud be the problem?


... Magic Chef DU6500 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2511 seconds