Having problems with your Samsung DMR77LHS Tall Tub Dishwasher ?

We have a samsung dmr77xxx dishwasher and it keeps getting a 9E error and stopping> what is causing this error? thank you


Answers :

Most 9E error codes are caused by a sticky float located on the LHS of the dishwasher. You can sometimes do a temporary 'fix' by 'thumping' the left panel inside the dishwasher (towards the bottom).
Hello, Welcome to FixYa.

The 9E code as it pertains to your Samsung is as follows according to the Samsung service manual...

ERROR TYPE - Low water level detected.

OCCURING CONDITION - Occurs when low water level even after water supply resumes after low level is detected the 1st time.

POSSIBLE/EXPECTED CAUSES - a) Low level sensor defective. b) Low level sensor wire loose/not connected. c) Main PBA fault/defective ( main board )

Steps to resolve-check.
Check for foreign material in the floater of the Low Level Sensor.
- Check the voltage between both ends (pink and brown wires) of the Micro Switch.
When operating normally after water is supplied:
- Check only the Micro Switch.(Remove the connectors before checking.)
Lift the lever: Short
Lower the lever: Open


Results.
- Faulty: Replace the Low Level Sensor, Remove foreign material from the floater
- Normal: Replace the Main PBA assy.

\015\012
\015\012\015\012\015\012\015\012\015\012Check for foreign material in the floater of the Low Level Sensor.
- Check the voltage between both ends (pink and brown wires) of the Micro Switch.
**When operating normally after water is supplied:

- Check only the Micro Switch.(Remove the connectors before checking.)
Lift the lever: Short
Lower the lever: Open

If you don't think this is something within your scope of abilities please call an authorized Samsung service center in your area.

Let me know what you find and I'll be glad to help you in whatever manner I can. Good luck.

Regards,

Macmarkus :)
Repair Help & Product Troubleshooting for Samsung DMR77LHS Tall Tub Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a samsung dmr77xxx dishwasher and it keeps getting a 9E error and stopping> what is causing this error? thank you


Most 9E error codes are caused by a sticky float located on the LHS of the dishwasher. You can sometimes do a temporary 'fix' by 'thumping' the left panel inside the dishwasher (towards the bottom). ... Samsung DMR77LHS Tall Tub Dishwasher

-keep getting error message LE -doesn't clean well if it does get through a cycle without error. -sounds like it starts and stops every few seconds.


Same problem as mine and unforutunety fix was a replacement motor which drives pump. Bearings were shot in motor. Lots of people have this problem. If you are good at repair you can buy motor on ebay for $60. Impeller will have to be removed ins ... LG 24 in. LDS 5811 Built-in Dishwasher

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

Hi i have a whirlpool dish washer - model : ADP4731/5 , AAA class . I keep getting a F7 error message and it is not allowing me to turn the washer on , if i hold the start button down it allows the washer to go for 30 seconds before the error comes back up and it stops working again


... Whirlpool Dishwashers

How do I locate the aqua stop on my smeg DWI612 as I keep getting the error code E1 and don't know how to check if the aqua stop is still in the 'closed' position. Thanks


... Dishwashers

Hello, my hotpoint ultima FDW85 keeps coming up with a H20 error code, even though the water s getting through ok it stops partway through a cycle, how can i repair this? Many thanks.


... Dishwashers

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

I have an LG LDF7811BB dishwasher. Keep getting the "LE" error code. I have replaced the entire motor/pump assemble, main PCB, and both of the other PCB's still getting the "LE" error code. Was very pleased with the performance until this. Am I missing something?


Hi,\015\012This seems to be a very common problem withe these dishwashers. The LE error code (locked engine) is not allways indicative of a motor problem. Sometimes one of the gray wires which runs the length of the door panel was pinched and b ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Detergent error I keep getting add detergent message. The bottle is not empty, the pickup line is submerged in the detergent & it tests acceptable. i also get an E7 error code once in a while. Thanks


I'm a hobart tech---been away for awhile.What is the model lxih,lx30?Let me know if you still have a problem with it. ... Hobart 24 in. LXIC-5 Built-in Dishwasher

Samsung Dishwasher can drain, but gives "drain error"


Sounds like it could be those same water level sensors you worked on before. Only now its telling the thing that there is water still standing in the unit. Try cleaning those sensors again and I know this sounds obvious but check all your conections. ... Samsung DMT400RHS Builtin Dishwasher

Hi . I have a Zanussi DE6965 which has started displaying the error message AL6 every now and then. When it stops and shows this the water has not pumped out. If you turn it off, leave for half an hour or so and turn back on it sometimes works fine to the end. Sometimes it stops again. Eventually after several stop starts it works through. Any advice what could be causing this? Thanks.


... Zanussi 24 in. DE6965 Built-in Dishwasher

ASKO d 3122.. Keeps filling up the overflow area on the bottom of dishwasher. WHich sets of the overflow switch, then i get the flashing tea cup again. I will empty the over flow area. It will reset, We get one good wash out of it then on the next load it will stop work ing again and get the flashing Tea cup again, Back to unplugging the unit and draining the overflow area again.


... Dishwashers

I cant get siemens dishwasher to work . An error E25 keeps appearing on the screen . What does this mean ? and how do I get rid of it and get machine to wash ?


... Siemens 24 in. SE20T590GB Free-Standing Dishwasher

I have a viking dishwasher model DDB325SS that keeps on getting a pan flood error. Once the error is cleared after several day of letting it dry out, I try and run it again. Immediately after starting it and water flows the pan flood error occurs. Any suggestions?


... Viking Dishwashers

Button error on samsung dmt800


... Samsung DMT800RHS Dishwasher

My brand new simens SR45M280SK dishwasher keep getting error code E21


... Siemens Dishwashers

I keep getting a washer arm blocked error.


I have had the same problem for a couple of years. When it tops without opening the door just press the start button and it will resume and finish the load. ... GE Profile PDW8400J Built-in Dishwasher

Error code I keep getting an error code R02 on my Indesit DE 73 dishwasher, can anyone tell me what this means


... Indesit 24 in. DE73 Evolution Free-standing Dishwasher

My dishwasher filter keeps getting plug up with large food particles. I take it apart and clean the screen. It works for a 2-3 -4 weeks before I have to do it again. There is a spinning fan on the screen. I'm wondering if this scrapper fan is working at all. If it was I think it would keep the small screen free from particles. The first thing that happens is the top cleaning arm stops working.' Thanks


Hi Judy. The only way to know for sure is to power up the fan independent of the machine and see if it still works. In the meantime, rinse and remove all debris from the dishes prior to placing them in the machine, including pots and pans. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Error 4 on whirpool adp600 keeps flashing, how do I get rid of the error message?


... Whirlpool Dishwashers

I have a Baumatic dishwasher and the E4 error message keeps coming back. We empty the water in the base of the unit, check the float triggered switch OK. It works for a while then the error re-occurs as the sump fills up again. What could be the cause?


... Baumatic 23 in. BFD61SS Free-standing Dishwasher

Hotpoint hda 3420 dishwaher. when turning, on the motor hums and doesn't kick in like usual. manual says caused by non use. "must keep the seal moist" put water in the unit, thinking it might get the seal moist. bottom filled and unit has not worked for days. assuming it's this seal: where is it? how do i get at it? what is replacement difiiculty? how much is the part? thanx ron [email protected] or [email protected]


Hi,Before thinking about replacement... pour a couple of cups of water in the dishwasher and let them soak the seal for overnight...Then if it don't go give the motor a spin...just to make sure it will go...if that don't work ... Dishwashers

Bosch Dishwasher Cycles will not stop running. They keep starting over. Help please!! Our 2 year old dishwasher will not stop running. It gets to the end of the cycle and starts over again. Plus, the cycles seem to have gotten longer. We called the Bosch repair number and they want $150 in cash to come out and look at it. Then they will come out and fix it!!!! Unbelievable!!!


Carry out a reset.\015\012This should reset the board back to factory settings,\015\012Deep Diver ... Bosch 24 in. SHU5305UC Built-in Dishwasher

Dishwasher not getting enough water in either drawer, although top drawer gets more. Dishwasher keeps beeping during cycle and reads not enough water and then stops running until you press the start button. Need Help, any ideas?


This sounds like a hard water deposit problem.Check your water inlet valve for a screen and see if its clogged. Also it may just be a water valve/solenoid problem. As in, it's too crusted up to float up and down.Some models have a water f ... Fisher and Paykel DD605FD Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1400 seconds