Having problems with your Samsung DMR78AHS Builtin Dishwasher ?

I am getting a CE error, what does that mean? Bill


Answers :

4. Troubleshooting
\012

4-2
\012

4-2. Service Inspection Mode
\012

- Press the Delay Start + Normal + Power keys at the same time for two seconds to enter Service Inspection Mode.
\012

- "ALL" is displayed for the first three (3) seconds and then "t1" is displayed.
\012

- You can change the mode by pressing the Normal key. Each time the Normal key is pressed, the mode changes in the order of t1 → t2 → t3 → t4 → t5 → t6 → t7 → t8.
\012

- If you want to activate a mode while operating the dishwasher, the door must be closed (The Door switches are ON.)
\012

- If an "oE", "LE" or "tE1" error occur, make sure to enter Service Inspection Mode after resolving it.
\012

- Service Inspection Mode is described in the following table.
\012

Mode Related parts Symptoms Note
\012

t1
\012

Inlet Valve
\012

Flow Meter
\012

Low Level Sensor
\012

4E
\012

9E
\012

If you press the Delay Start key, water is drained for 45 seconds and then the water supply starts.
\012

If the pulse count is more than 660, change the mode.
\012

Make sure to change the mode when the pulse count is more than 660 in t1 mode.
\012

t2 Circulation Motor A nozzle does not inject
\012

water.
\012

1. Press the Delay Start key to start or stop the Circulation Motor.
\012

2. If a low water level is detected, water is supplied again and the operation continues.
\012

t3
\012

Circulation Motor
\012

Heater
\012

Thermistor
\012

HE
\012

1. Press the Delay Start key to start or stop the heater and the circulation Motor.
\012

2. If a low water level is sensed, water is supplied again and the operation continues.
\012

3. The current temperature is shown on the display.
\012

4. If the water temperature is more than 70ºC, the Heater does not operate.
\012

t4 Fan Motor The Fan Motor does not
\012

operate. Press the Delay Start key to start or stop the Fan Motor.
\012

t5 Drain Pump
\012

Low Level Sensor 5E 1. Press the Delay Start key to start the 2 parts.
\012

2. When draining is finished, "t5" is blinking on the Display LED.
\012

t6 Low Level Sensor
\012

When the Micro Switch
\012

is turned on/off, there is
\012

no change on the display
\012

or a symbol other than
\012

On/OFF is displayed.
\012

1. MICRO SWITCH On
\012

→ The sensing state is displayed as 'On' on the 88 segment display.
\012

2. MICRO SWITCH Off
\012

→ The sensing state is displayed as 'OFF' on the 88 segment display.
\012

t7 Thermistor There is no change in the
\012

water temperature. The current temperature is displayed.
\012

t8
\012

Half Load Position of
\012

Distributor Motor
\012

Micro Switch
\012

(DMR77 Model)
\012

PE
\012

1. If you press the Delay Start key, the parts operate just once.
\012

2. There is no stop function.
\012

3. While the Distributor Motor is operating, its sensing state is displayed as On/OFF on the 88 segment display.
\012

4. When the Distributor Motor stops, the sensing state (On/OFF) of the Micro Switch is displayed.
\012

Caution
\012

If it has the power problem, you must check the FUSE first.
\012This dishwasher has the FUSE upon the Base. Refer to the 4-10 page.TRY THESE STEPS AND SEE WHAT HAPPENS THERE IS NO CE FAULT CODE LISTED IN THE MANUAL

Repair Help & Product Troubleshooting for Samsung DMR78AHS Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am getting a CE error, what does that mean? Bill


4. Troubleshooting\0124-2\0124-2. Service Inspection Mode\012- Press the Delay Start + Normal + Power keys at the same time for two seconds to enter Service Inspection Mode.\012- "ALL" is displayed for th ... Samsung DMR78AHS Builtin Dishwasher

What does the F2 Error mean? I got that error thsi morning. The engine was buzzing so I turned the power off. I have cleared what appears to be calcium and/or soap build-up in the 3 filters and in the drain. When I turn the power back on I still get the F2 error. How can I restart the machine and turn off the F2 Error?


The F2 error means the tray underneath the unit has filled with water.\015\012You will need to pull out the dishwasher (remove 2 screws at top left/right when door open that prevent tilting).\015\012Unplug and pull out dishwasher.\015\012Remove 4 scr ... Asko D1876 Dishwasher

I cant get siemens dishwasher to work . An error E25 keeps appearing on the screen . What does this mean ? and how do I get rid of it and get machine to wash ?


... Siemens 24 in. SE20T590GB Free-Standing Dishwasher

I keep getting an E1 error on my LG LD-2120W model dishwasher, can you advise what this means so l can either fix it or get it fixed. Thank you


Leakage Error E1\015\012\015\012\015\012\015\012\015\012The excessive RPM of Washing Motor happened during Washcycle due to water leakage.\015\012\015\012Water leakage in ... LG Dishwashers

Error code I keep getting an error code R02 on my Indesit DE 73 dishwasher, can anyone tell me what this means


... Indesit 24 in. DE73 Evolution Free-standing Dishwasher

Got a Miele G2220sci dishwasher unit, getting an undocumented error code of F19 with flashing lights, help! what does F19 mean? WONT DRAIN. PROGRAM FINISHES WITH F11


F19 is water in the cabinet takes too long to heat up. you can reset the heater limiter..\015\012\015\012Reset the error message as follows: To cancel the error message, turn the rotary selector switch to "Stop/End" or press the "Start/St ... Dishwashers

Dishwasher repair Bosch Dishwasher SMI69M15EU/01 error E20. When turning on the dishwasher you can see he activates the drain pump for a second Then the circulation pump en immediately after this I get a E20. Do's someone the meaning of the E20 Event?


... Bosch Dishwashers

Hi guys. I am getting an error message AL10 on my Hotpoint Super Silent FDW80 dishwasher any ideas what this means?


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

What is the error code EC mean? Bill - Samsung Dishwashers


Hi,Kindly mention the make and model of the appliance? Is it Dishwasher or Tankless hot heater water?Thanks and Regardstaran_2005 ... Samsung Dishwashers

I have a Turbo (made in Italy) integrated dishwasher that gets part way through the cycle (about 3/4 through) then beeps and stops with error code E4. Do you know what this means and how I can fix it please?


... Dishwashers

We have a Hobart FXS 70N Dishwasher and it gives us a F04 error code. What does it mean and how can it be fixed? Where can we also get a wiring diagram for it? Thanks Engela


... Dishwashers

I get an AL10 error code on my SDW80 dishwasher what does this mean


... Hotpoint Dishwashers

What does E8 and F1 error codes mean? We get this at the beginning of the cycle and the dishwasher shuts off?


... Bauknecht Dishwashers

Getting error message E1 what does this mean - LG LDF6810ST Stainless Steel Built-in Dishwasher


E1 leakage error\015\012\015\012The excessive RPM of\015\012Washing Motor\015\012happened during Wash\015\012cycle due to water\015\012leakage.\015\012\015\012\015\012Water leakage in Hose connections.\015\012Water is leaked by damages.\0 ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I have an Electrolux dishwasher Model # EIDW6305GS1. I am getting an error "01", which means a leak is detected. It did this 5 months ago and the repair man replaced the pump and control panel. Now, after it happened again, I contacted Electrolux. The sent me a Leak Repair Kit, but with no instructions. I contacted Electrolux again and they said that they could not provide the installation guide. Can you help me located the installation guide or offer assistance?


... Dishwashers

Got a Miele G2220sci dishwasher unit, getting an undocumented error code of F19 with flashing lights, help! what does F19 mean?


Miele tech's say this is a "Flow Meter" problem, which could involve their service department. ... Dishwashers

Model No- LD-12AW2 LE Error showing what does this mean


LE error code means that there is a problem with the motor.  One thing to check is to remove the front door panel and check the wiring harness to see if there are any broken wires.  If there is, repair the wire connections and see if the di ... LG 24 in. LD-12BW5 Free-standing Dishwasher

OE Error I'm getting an OE error which is a drainage trouble error. I checked the hose and the drain, and everything is clear. My diswhwasher runs 98% of its full cycle and usually with 2 minutes to go I get this error. I have 2 opinins as to why this is happeneing. 1. Maybe the clog is in my trash compactor, however that seems to be working fine and my sink is funning with no slow down. 2. My 2nd theory is I have to reset the progam within the dishwasher. Like how sometimes I


Had the same problem and had the pump replaced ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

I am getting an error message 002 on my Conia


... Dishwashers

I get an LE error message on my LG Dishwasher. I replaced the pump. Still get the LE error. Replaced the main control. Still get the LE. No blockage in the pump. What now?


When you receive the LE error code, unplug the machine for approximately 15 - 20 minutes. This will reset the microprocessor.Oversudsing is the main cause of LE error codes. Using non-HE detergents or too much detergent will cause stress ... Dishwashers

C3 error on a 2230 ge potscrubber dishwasher. Reset it, turned it back on, then get C4 error. Continue to get errors and dishwasher won't drain


... Dishwashers

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

Blomberg DWT34240 error code IF. What does that mean?


Hi, same dishwasher here, same error code. Did you or anyone find out more about this?Thanks!! ... Blomberg DWT34200 DWT34210 DWT34220 DWT34240 24 in Builtin Dishwasher

On an AEG Favorit 64570 VI we have an error 20. Manual indicates a drainage problem, however when we pour in water, it gets pumped out without a problem. No obstructing in the exhaust tube. Next we checked the pressure sensor, by taking it out and blowing into it. It clicked as pressure was applied to it, so the inner switch worked. Everything is clean, but still we get an error 20. What does seem strange is that the appliance does not take in water. Any suggestions are welcome.


... AEG 23 in. Favorit 86070Vi Built-In Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0948 seconds