Having problems with your Samsung DMR78AHS Builtin Dishwasher ?

Have code oE is this over water level sensor is it accessed from bottom of washer? is it a sensor or is it a switch is this a common problem?


Answers :

Drain Error OE
Not fully drained out in spite of 5 min. drain operation
The Drain Hose kinked or blocked. Wiring connection is OK? The drain outlet of sump is blocked. The Drain Pump/Motor or circuit is troubled.
Remove the cause of kink or block. Check the wiring connection. Measure the electric resistance of Drain Motor. (20-40 ) Replace the Drain Motor or repair the Circuit
Repair Help & Product Troubleshooting for Samsung DMR78AHS Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have code oE is this over water level sensor is it accessed from bottom of washer? is it a sensor or is it a switch is this a common problem?


Drain Error OENot fully drained out in spite of 5 min. drain operationThe Drain Hose kinked or blocked. Wiring connection is OK? The drain outlet of sump is blocked. The Drain Pump/Motor or circuit is troubled.Remove the cause ... Samsung DMR78AHS Builtin Dishwasher

I have an Ariston LI45. The stupid thin one. It's not seen much work & is just out of Guarantee. It's stopped working & is showing 2 flashing lights. Stops partway in to a cycle with water in the base, but not enough to cover the element. Tried re-setting, no difference. I have also noticed that it's melted a plastic wheel off the bottom tray at the back. After reading problems with other washers, i'm guessing the water level switch & maybe element too. If this is the case, i'm ok finding the


... Dishwashers

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

My bosch dishwasher runs fine, cleans fine, drains fine....but after it has been just sitting for a while, the bottom very slowly fills up with water. Each time we run the machine the water level drains back to the normal amount in the bottom of the washer after the cycle is complete. The problem is if we are away for a few days, the bottom fills up and overflows onto the floor.


Water inlet valve isn't closing all the way closed. Need a new one ... Bosch 24 in. SHU53 Built-in Dishwasher

Smeg DWF612WH dishwasher has developed a leak. Water comes out of the rectangular hole on the side of the water softner used to mount what looks like a level or pressure switch. A few seconds after the fill valve opens water leaks out, not a lot just a small trickle. After the washer has filled and goes ito its cycle, it does not leak again. Over the past weeks the problem has got progressively worse.


... Smeg 24 in. DWF612WH Free-standing Dishwasher

The top drawer of my fisher paykel dishwasher stops during the cycle and shows an icon of a tap with a line threw it (assume that means no or low water pressure). the bottom works fine so I assume water pressure is not the issue; is there a sensor that could be bad? Also, I did switch the controllers between drawers (good instructions on the fisherpaykelparts.net website) but the problem stayed with the drawer, ruling out the controller.


Did it fill with water? could be 1 of your water valves is faulty, or the little filter for the inlet water is blocked. please reply 4 more help. i"m sure i can fix this problem for you. good luck. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Rockworth Powertask Pressure Washer : model no AROW4P seems to rev flat out, hav to put choke in middle to use so not to fast revs. Im sure it used to rev higher and lower according to use of lance. could it be something to do with 3 valve things if so how could i tell if ok. put clean fuel in. oil level ok.another problem is when switched on water comes straight through lance,trigger makes no diffrence. please help


... Pressure Washers

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi


Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers

I have a Whirlpool Gold GU3600XTSY0 Model. There is slow water leak from the right side bottom front of the dishwasher. It looks like the water is leaking from a sensor on the bottom. The sensor has a pin protruding that can push up and down...almost like an on/off switch. I am wondering if there is any way to fix this. Water is leaking on my hardwood floors.....


That is your overflow water switch, that tube goes up to the washer, that switch is defective..water from the machine will come thru that hole ... Dishwashers

I have a Samsung dishwasher and a code comes up that says that there is a low-level water function problem. The solution in the manual says to run it empty to clean it. I suspect that the water level chamber may have food deposits in it causing the low-level sensor to misfunction. Where is the water level chamber and how do I clean it?


... Samsung Dishwashers

Asko 1605 Dishwasher: Intermittent problem with water ending up in the bottom pan


... Asko Dishwashers

Kenmore dishwasher 587.15163401 won't fill. I checked the float switch with my multimeter and it's working properly. It's registering zero when I touch the terminals and 1 when I activate the switch. On this particular washer, how do I access the water inlet valve to check it for debris and also to check the solenoids? Also on this particular washer, how do I access the drain valve and solenoid. Can you tell me if this is a single direction motor or reversing motor. As I understand


The problem was the water fill valve. When set to Ohms, the multimeter never would read zero indicating a problem with the water fill valve. I replaced the part and it works now. Be sure to turn your water off under the sink before taking it off t ... Dishwashers

Check water light stays on rendering machine unuasable.checked water supply.all filters .googled problem told me to switch water supply on and off rectified problem for 10 minutes then check water light came back on. water remains in bottom of appliance.


... Bosch Dishwashers

Hi my L G dish washer is coming up with E1 . It comes on after about 2 min it takes water into the washer then it hummes for about 30 seconds then comes up with E1 and pumps water back out. I have checked the hoses which don't appear to be leaking -I read somewhere in your answers about this problem that it could be the Water Level in Drum lowering, this means there is a leak on one of the pipes. More likely it is the Circulation Pump, which is responsible for pushing the water to the Spray


Hello aderry -\015\012\015\012\015\012I'm a bit short of time as I'm on my way out to a service call, but I've uploaded the service manual to Rapidshare for you to download. \015\012\015\012\015\012Rapidshare download inst ... LG Dishwashers

Got a Indesit Di620 Dishwasher that trips RCD after power up & immediateley as you shut door.Fault is definately related to pressure switch, disconnected pipe to switch and then able to start cycle, without tripping, small amount of water out of pipe,but cycle only lasts for a few minutes, then stops. ( blowing into pressure switch trips rcd )How can i test switch, or is it a water level problem ??Any help would be good, thanks S.C


... Dishwashers

Hi i dont know the model of the dishwasher.. but the controls are fairly staright forward... a little knob for temperatur control and an on/off button.. and a light that lights up green when dishwasher is switched on... now the problem is as happened recently, when you switch the washer on greenlight is on and washer can be heard doing something but after a minuit or so the washer stops and the green light flashes. open up the dishwasher no sign of water or that it has done anything at all... th


It sounds like your washer is not getting enough water to start. If your washing machine is filling too slowly or not at all, then you probably have a clogged screen on the back of your washer. To check this: \015\012\015\012 ... Whirlpool Dishwashers

Kleenmaid DW8 top washer does not operate. Apparent blockage in the water supply tube which runs up from the bottom water supply. How do I remove the bottom assembly comprising the main filter, waste trap and micro filter? I appears that these must be removed to access the water supply tube mentioned above.


... Dishwashers

I have a kenmore 665.13719k601, i used the delay switch and now i found water in the bottom of the machine. the cycle most have stopped while i was away. when i returned there was water sitting in the bottom of the machine. The water is clean... I can not drain due to no access to power on the machine. I checked the breaker but it was on, so i reset it anyway... nothing.. any idea's


... Kenmore 13719 / 13712 Built-in Dishwasher

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

Maytag dishwasher- Model # WU 502 serial # 145 192 EP- 03 series Water builds up in the bottom of the dishwasher, does not overflow but will not go down. Nothing appears wrong in the drains. Dishwasher is connected to the kitchen sink drain. Tried a seperate rinse cycle but did nothing to eleviate the problem just made the water rise a bit but still did not overflow out of the washer. This washer is old and I cannot find the manual that came with it.


... Maytag 24 in. MDB6657 Built-in Dishwasher

My dishwasher will start any program, it drains, fills, empties & beeps continually within a few minutes. The rinse light stays on until the machine is turned off & re-set. Aditonally, the ater heating has been hit & miss for some time! A service guy cleaned the water sensor with hot water fro a ketle + tooth brush, but the problem came back after a couple of weeks. Having removed item he cleaned, it looks fine and appears to switch OK. Not sure if its actually faulty. Is the themperature sensor


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Motor makes noise shortly after starting, makes normal sound level during main body of wash, then makes noise again during what I'm guessing is the rinse cycle. Not sure if it is a pump or motor problem. Slight electrical smell noticed after finishing the ''cancel/drain''. Water does not seem to be sprayed around washer during normal cycle, even though water has been in the washer.


Make sure the sprayer arm is turning freely, check for something stuck in the base of the sprayer arm (food or utinsel) preventing it from turning. ... Dishwashers

Hi there, I owe A GE GSD5911D01SS Perfil Performance Quiet Power III dishwasher. The problem is that during cycle, it leaks water through the left corner, is like the water level is too high, the sensor light lit up, which doesn?t tell me much. This issue doesn?t happen all the time, yesterday was the second time and I have no idea of what it could be the problem. Can anyone help? Thank you.


... GE Dishwashers

We recently purchased a Whirlpool ADP 4736 dishwasher, and just last night while it was working the fuse just blew, and we heard a popping sound at the back of the washer. We tried to replace the fuse, but the same problem. rnAlso, there a lot of water has collected at the bottom of the washer, although the dishes have been cleaned and dry. What could be the problem and the solution for this. All the instructions are in Polish and made in Poland. Please advise?? Many thanks Percy'


... Whirlpool 33 in. ADP6830 Free-Standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2003 seconds