Having problems with your Samsung DMT800RHS Dishwasher ?

Water dosen't circulate -wash or rinse cycles

\015 No water to spray arm inside\015

Answers :

Repair Help & Product Troubleshooting for Samsung DMT800RHS Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Dishlex 100, it seems to fill with water, but then when it fills it just stops. Dosent do anything. It just clicks through the cycle without washing. It then seems to empty out water and refills it to rince but once again dosent actually do anything but click through rinse cycle then clicks along till the emptying out cycle comes up to empty it.


... Dishwashers

Our Miele G975SC dishwasher has developed a problem - it starts a wash or rinse cycle as normal - it pumps out, then fills with new water and starts washing as expected. Then it just carries on circulating the water and heating the water. It ran like this for at least 2 hours before we interrupted it by switching it off


... Miele Dishwashers

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

When I started it, it made a loud grinding sound which continued whenever it was actually washing/rinsing. It was washing and rinsing the dishes ok. Eventually I didn't hear anymore grinding but the dishes had not been washed or rinsed. The detergent cup was open and the detergent spilled down the door. I ran it again and could hear the pump running. It ran through the cycles but the water was not being circulated. I suspect that something is caught in the disposer blade or something and is bloc


What is the brand and model number. it likely will have to be disassembled to clean it out. is it a built in dishwasher or a stand alone type ? ... Dishwashers

Amana softsound 111 dishwasher, model adw750eaw - The dishwasher fills with water fine and drains water fine, but will not circulate water during the wash and rinse cycles. Any advice?


... Amana Dishwashers

Kenmore ultra wash fills w/water and heats to temp but no circulation of water or cycling thru wash or rinse


Call the store where u got this machine as you have a 5 year warranty on the motor and the pump. ... Kenmore Dishwashers

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

ASKO 1885 Built-in Dishwasher: The water sump fills normally, but the wash cycle does not start. Althought the timer seems to work, the wash cycle motor won't start up in any wash or rinse selection. The spray arms do not spin - no water is being pumped. At the end of the wash cycle time, the water will empty out of the sump. Thank you. TB


Hi, Welcome to FixYa. Based on your description and provided the dishwasher is indeed 1) an Asko 1885 and 2) filling ... Asko 24 in. 1885 Built-in Dishwasher

501ht goes thru wash cycle but cam stops just before rinse cycle clicks in - stays in wash cycle - turned thermostat to booster down in temp -cam then keeps going properly but with no hot water from booster - replaced thermosat still same result - apparently a safety ? no booster water no rinse?


Did you get a solution for this? I am having the same issue. Please email me at [email protected] Thanks -Eric ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

Water dosen't circulate -wash or rinse cycles


... Samsung DMT800RHS Dishwasher

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

FDB1050REM2 dosent go through wash cycle. it will fill drain dry etc. will not move the water to wash the dishes


... Frigidaire Dishwashers

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

I have a ADG 450 dishwasher, it has suddenlt topped completing the wash cycle. it runs for about an hour then sits and beeps. If i open the door, the machine is full of water and it looks as though it is trying to spray more water in, thn stops and beeps. If i turn it off and on at this stage and run the rinse cycle, the water clears and the dishes appear to have been cleaned. any thoughts? it happens with all wash cycles.


... Whirlpool Dishwashers

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr


WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

DWI612C wash cycle runs on and on and on. Believing to be a problem with water heating I tried putting a couple large pan fulls of boiling water into machine during wash cycle and this did move it on from wash to rinse. How do I replace the heating element I cant see it it is not in the dish washing compartment? I dont want to call out a repair agent as one can probably buy a new machine for what that will cost. Thank you.


... Smeg 24 in. DWI612 Built-in Dishwasher

Dishwasher is not cleaning well, dirty film all over everything, like its not rinsing. In rinse cycle only, some water comes out of lower left port inside but nothing else. Hear a low buzz underneath unit like a motor or pump is energized but no water getting to the top.During normal wash cycle, buzz from underneath seems to cycle on and off, say every minute or so like its cycling on an overload. Do I have a bad pump and if so how do I get to it?


Hi. This may well be a pump issue, or an obstructed hose assembly, as well. Your symptoms are indicating that the impeller may be damaged. In order to pull the necessary schematics, I will need the entire model number. This ID tag will allow me to pu ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

Washer Dishwasher fills with water, wash cycle does not start up. The machine continues to go thru the wash, rinse, cycle, discarding water, filling again, etc. but no water sprays in the machine, Thanks for any help !


If I'm not mistaken, these dishwashers are built by Asko for Viking. If thats the case then you probably have a bad circulation pump. Under Asko's warranty (not sure if Viking is the same) these pumps are covered parts and labor for 3 years from inst ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

Dishwasher makes grinding noise during wash cycle (after pre-wash). noise persists for 15-20 minutes. It seems as though the inlet valve doesn't open during this phase of the cycle. adding water to the dishwasher manually eliminates the noise and water circulates through the wash arms. I'm trying to determine if this is a controller issue or a valve/pump issue.


Water-inlet valve\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012\015\012\011\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\01 ... KitchenAid Dishwashers

My KDS 19 Kichenaid dishwasher goes thru the wash cycle, but at the end there is about 1/2" water still in the bottom. The punp work OK druing the wash and rinse cycles, but at the end of the drying cycle there still is watere in the bottom.


Would you have the model number at all? It should be on the left edge of the dishwasher's door. Thanks. ... Dishwashers

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

Dishwasher pumps dry, adds and heats water, but does not go through wash cycle. It apparently continues through all cycles, but never pumps the water through the spray arms in either wash or rinse cycles. spray arms are both free and clean, no debris anywhere obvious.


Hi.The impeller pump is probably faulty. Before going for the pump check the drain well and drain hose, drain blockage may prevent the machine from switching to recirculate. Also double check there is no blockage or leak in li ... Asko 1385 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1838 seconds