Having problems with your Samsung DMT800RHS Semi-Integrated Dishwasher with 6 Wash Cycles, Adjustable Nylon Racks, Tall Tub, Storm Wash, Hard Food Disposer, 2-Stage Filtration, Blue LED Exterior Display and 48 dBA Silence Rating: Stainless Steel ?

9E error code on dmt800rhs dishwasher - Samsung DMT800RHS Semi-Integrated Dishwasher with 6 Wash Cycles, Adjustable Nylon Racks, Tall Tub, Storm Wash, Hard Food Disposer, 2-Stage Filtration, Blue LED Exterior Display and 48 dBA Silence Rating: Stainless Steel


Answers :

I also had the 9E error code on my Samsung dishwasher DMT800RHS mmodel. I had to call Samsung and the nearest authorized Samsung service representative came to my house last Tuesday, January 29, 2013. The cost of the call is $100 which really annoyed me off considering the dishwasher is only 1 1/2 years old. Two South Korean guys showed up and to fix the problem just press down on the Heavy, Delicate and Power button at the same time for a few seconds and a menu will appear on the top left hand corner of the panel. Scroll down the menu by pressing the Normal button until you reach "FT" and the dishwasher will automatically fill up and then autimatically drain. If it does not drain then scroll down to "S" and the dishwasher will drain. Thsi should get rid of the 9E error message and your dishwasher will work fine but if not you have to repeat the procedure maybe 2 or 3 times until the 9E error message disappears. If you constantly get the 9E error message then you may need to replace the part which is about $60. The part is extremely sensitive to either hard water or food particles which is why the 9E error message appears. Therefore, scrape your dishes thoroughly so the food particles are minimized and the sensor does not go off which causes the 9E error message.
I had same 9E low water level error. Removed the lower nozzle, then the plate at that bottom (lots of screws to remove) that covers the float. On the underside of that plate was a thin round piece of rubber that I think you would call a gasket. It was far to big and excess gasket was outside of the groove made for it. The excess was in the area around the float. I figure it was interfering with float operation. I snipped it and retreaded it into the groove. I have not had a 9E error since and have cancelled service call that would have cost me min $104.
Repair Help & Product Troubleshooting for Samsung DMT800RHS Semi-Integrated Dishwasher with 6 Wash Cycles, Adjustable Nylon Racks, Tall Tub, Storm Wash, Hard Food Disposer, 2-Stage Filtration, Blue LED Exterior Display and 48 dBA Silence Rating: Stainless Steel

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

9E error code on dmt800rhs dishwasher - Samsung DMT800RHS Semi-Integrated Dishwasher with 6 Wash Cycles, Adjustable Nylon Racks, Tall Tub, Storm Wash, Hard Food Disposer, 2-Stage Filtration, Blue LED Exterior Display and 48 dBA Silence Rating: Stainless Steel


I also had the 9E error code on my Samsung dishwasher DMT800RHS mmodel. I had to call Samsung and the nearest authorized Samsung service representative came to my house last Tuesday, January 29, 2013. The cost of the call is $100 which really annoy ... Samsung DMT800RHS Semi-Integrated Dishwasher with 6 Wash Cycles, Adjustable Nylon Racks, Tall Tub, Storm Wash, Hard Food Disposer, 2-Stage Filtration, Blue LED Exterior Display and 48 dBA Silence Rating: Stainless Steel

My DMT610RHS/AC is showing error 9e - Samsung DMT800RHS Semi-Integrated Dishwasher with 6 Wash Cycles, Adjustable Nylon Racks, Tall Tub, Storm Wash, Hard Food Disposer, 2-Stage Filtration, Blue LED Exterior Display and 48 dBA Silence Rating: Stainless Steel


... Samsung DMT800RHS Semi-Integrated Dishwasher with 6 Wash Cycles, Adjustable Nylon Racks, Tall Tub, Storm Wash, Hard Food Disposer, 2-Stage Filtration, Blue LED Exterior Display and 48 dBA Silence Rating: Stainless Steel

No Water Coming Into SHU43C05UC/12 Bosch Dishwasher: We have a Bosch Dishwasher, model number SHU43C05UC/12. It has been working for more than 4 years, but yesterday I notice that although I hear a motor sound, there is no water in the dishwasher. The LED display on the panel seems to be working all right. I ran a diagnostic pressing and holding Power Scrub and regular wash button then pressing the on/off button. Got C1 at start then P0 and the Regular wash and Quick wash flashing on/off. How c


... Dishwashers

Our GE built in dishwasher Model GHD6310L18WW had no lights on and would not operate. i checked the breaker panel and found it was OK and 120vac were flowing to the unit. i then turned the braker off for 30 seconds then back on .this made the time remainig LED display sow 106 and the Normal wash Cycle LED is lit as well as the extra Heat LED . the unit will bot operate though


... GE Dishwashers

Frigidaire Gallery Series Dishwasher - unit stops near the final rinse cycle without draining - "ER" on front display, all led indicators on front display also lit (e.g. low rinse agent, etc.), and the "Hi Temp Wash" light is lit, regardless of cycle setting at beginning of cycle - rinse cycle seems to function normally


HI,check your drain hose first for kinks or food blockage also check the\015\012tail at the disposal or wherever you drain hose connects. Second there\015\012may be a blockage in the pump itself take it off and check. If all of\015\012thi ... Dishwashers

My dishwasher LED display seems to have gone off. The On/Off button still lights up but the display showing the program has ceased so it doesnt start as washing program. Is this a terminal problem? John Lewis JLDWW1201


... Dishwashers

I have a Bosch dishwasher, stainless steel front- with buttons on the inside top( same as display, and the washing cycle won't start. Water seems to be running into the washer, as I can hear it, but the cycle never starts. Recently, I had clogged garbage disposer issue that has been resolved. The dish washer drains into the disposer, and I had free standing water left behind in the washer for 2days during this time.. Could this be the issue? Can you help me figure out this problem? Thanks!!


... Bosch 23 in. SHU 8805 Built-in Dishwasher

We can't find our owner's manual. We bought a Siemens dishwasher in 2003. We just interrupted the drying cycle and now the dishwasher won't close all the way and the LED display is off, but if we push the on/off button, it starts a new wash cycle. We don't want to let it run because we're afraid of flooding. Advice?


Close the water inlet tap ****. Give a try and finish the entire cycle. ... Dishwashers

I have a Bosch dishwasher model SHE4AP02UC/06, serial number FD901102579 that has been used twice since installation. When I select the Regular Wash cycle, the Regular Wash LED and the Active LED come on. The machine washes the dishes and then when it stops making noise. At that point the Active LED goes off and the Clean LED comes on with the Regular Wash LED. These LED's do not go off. There is no signal saying that the dishwasher is finished. Is this the way it is supposed to be operating or


Ya id say until u open the door after it has washed ... Bosch Dishwashers

Frigidaire dishwasher Model# FDBB4365FC0 Display shows PF (blinking) Air Dry and High Temp Wash LEDs are blinking Electronic board has recently been exchanged.


Hi t_l_stock...hope this helps..Good luck..Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may require a water heating delay, such as Hi-Temp Wash, Hi-Temp Rinse, or Sanitize. Additional time may be re ... Dishwashers

The dishwasher will not do anything. The normal wash cycle led flashes and the lcd display shows --. I have reset the breaker and tried to reset the dish washer and still nothing.


What does the lcd show it says this -- in your post ? or is that all it shows is two dashes first thing to try is hold the cancel button for 5 seconds and then message me back with what the lcd shows i await your reply Thanks Rick ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

New product.samsung DMR57 series dish washer.instruction book says 110-194.wash time...blue leds display ''214''..have good solid 122A/c line...and good hot water supply..also noted inside of cab is wet after cycle...but dishes are dry..


... Samsung Dishwashers

Have a new GE Profile dishwasher. The LED time display started at 62 the first time we used the machine. It keeps going up and is now at 108. Is it broken and how do we reset the time back to something more reasonable. We typically pre-wash the dishes anyway and it shouldn't have to take that long to clean....thanks!


Have you tried to turn the mains power to dishwasher off and back on again.\015\012\015\012It also possible the inlet water temperature is not at the recommended temperature so it is compensating for heating it to the desired temperature. ... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

The kitchenaid dishwasher (model KUDC25CHSS1) appears to have the 'child lock' engaged on the led display panel. The 'energy saver dry' light is flashing red and when I attempt to push 'cancel' it only flashes and never goes away. When I attempt to press a 'wash selection' the 'child lock' then flashes. Please help.


On my unit, I had the same problem (child lock LED on, or flashing.The cancel process of pushing anything was not possible, as a bad/stuck switch prevented any input from the control panel buttons.The underlying cause of the problem turne ... KitchenAid Dishwashers

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

I bought an IKEA Renlig DW60 dishwasher about 6 months - the controls are located on the inside top of the door. Ordinarily the dishwasher turns on and three red LEDs on the far right of the control panel light up. On occasion however only a single red LED indicating the temperature of the last wash I carried out will go on (it is always the 50 degree light as this is always the wash temperature I use). When this happens the dishwasher appears to be stuck and will not start when I shut th


Press and hold the cancel button for about 5 seconds. This resets the electronics and gets it going again ... Dishwashers

Whirlpool dishwasher This dishwasher quit in the middle of a wash cycle,we had to empty it and wash by hand. I thought that maybe the breaker to the dishwasher popped but when checked it had not .I then noticed that there are no lights on the electronic key board .Even when not in use there should be one red LED that is lit. It almost seems as if there is no power to the dishwasher. Is there some type of backup safety switch or breaker on the dishwasher itself that I could reset?


Fuse on control board. ... Dishwashers

Westoint Dishwasher I have looked in the manual under troubleshooting tips, but didn't find anything on the problem. The dishwasher goes into cycle,but during the wash cycle it stops,makes alarm and the wash and rinse ligts come on. And now I can't even find the product on this site.Westpoint Dishwasher WQP12-9240. Thankyou My dishwasher is stopping at stage 2 of the programme after beeping once. Quite often the detergent flap doesn't open. Am at my wits end and threatening to leave home!!!! Th


Hi again,\015\012\015\012That should be OK. Just get in touch with your sales rep or his boss. Somebody there will be able to look up the record of the purchase. If they ask for model & serial numbers, you have them. You will find ... Dishwashers

Touchpad--No Response The touch pad and Countdown timer display will NOT respond except when the Rinse Only pad is pressed. The Countdown timer displays "9" when this pad is pressed. As expected the light and display turn off after 30s. If after 30s or longer the Start/Cancel pad is pressed with the dishwasher door closed, then the Countdown timer displays "2H" and the dishwasher runs through the ?Auto Clean? or ?Heavy Wash? cycle. Not sure which since neither pad is lit. Is the problem the


The "2H" is an error code indicating the control panel needs to be replaced. ... Bosch 24 in. SHU53 Built-in Dishwasher

FGHD2433KFI ER Multiple lights go on when choosing the wash cycle. Quick wash is brightly lit but heavy wash is less bright along with air dry. When Start is pressed display shows delay/50/S. After 10s or so the display goes off and the dishwasher doesn't start. The same thing happens if I try Quick wash again.


... Frigidaire Dishwashers

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

Have a 665-16293201 dishwasher with electronic controls and smart sensor. Approx 10 years old in great shape. it just started having a problem - it takes a long time for the sensing to be completed at the start of a wash and then the washer will start and display a time - like 92 minutes - turn the sensing light off, then start to wash and count down. when it gets to 86 minutes, it starts to sense again and will continue washing while displaying 86 and with the sensing light on. It will keep


... Kenmore 24 in. 16293 Built-in Dishwasher

My bosh dishwasher SHX55M06UC/46 will not drain. A new disposal was put in and the dishwasher drain plug was not punched out and the dishwasher was ran that way. Now it just holds water in the bottom. I've tried resetting or canceling the wash cycle but that doesn't work and the washing cycle works fine. I'm hoping there is a reset or a safety for the pump if it gets clogged.


... Dishwashers

My Hotpoint FDL50 dishwasher is tripping the fuse box circuit during the 1st stage wash cycle. I cancelled the wash cycle and switched off the dishwasher on the on/off button & the dishwasher still tripped the circuit.


... Hotpoint 24 in. FDW60 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2581 seconds