Having problems with your Shark Helmet Shark Professional 3000 PSI (Gas Hot Water) Pressure Washer W Honda Engi ?

My Pressure Washer leaks diesel fuel from under the hot box.Its has a Carlin Burner and I use regular Diesel Fuel


Answers :

Repair Help & Product Troubleshooting for Shark Helmet Shark Professional 3000 PSI (Gas Hot Water) Pressure Washer W Honda Engi

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Pressure Washer leaks diesel fuel from under the hot box.Its has a Carlin Burner and I use regular Diesel Fuel


... Shark Helmet Shark Professional 3000 PSI (Gas Hot Water) Pressure Washer W Honda Engi

My Diesel Fired Burner on my Hot Water Pressure Washer leaks diesel below the Hot box. It has new diesel from the gas station..


... Shark Helmet Shark Professional 3000 PSI (Gas Hot Water) Pressure Washer W Honda Engi

Brand new Northstar hot water pressure washer, 2000 psi, electric and Diesel fired burner. The burner will not come on??? It works ok as a cold water unit but the burner will not fire even with the Heat switch on and fuel in tank?? What could cuse this?


... Northstar Wet Steam & Hot Water Pressure Washer with Honda Engine 3000 Psi, 4 Gpm

Fuel leaks into base below burner fan and burner


... North Star Pressure Washers

My diesel burner on my pressure washer smokes real bad. Could I have a leak, if so where would that leak be? It is a alkota


HI, here is a few pointers that may help you , \015\012\015\012if the smoke is white , that usually indicates water in the diesel, empty fuel tank and replace/clean the fuel filter \015\012if the ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Two problems please: craftsman 2150psi briggs and stratton engine washer, will not start when hot. and secondly, i was washing with regular pressure, then noticed a pressure drop at the nozzle, then the unit shut down. no water leaks at the manifold. water supply was strong. any ideas?


Nozzle dirty, clean out with small diameter wire. ... Pressure Washers

My electric stea pressure washer wont ignite burner it burns on diesel fuel what is the problem


There can be multiple reasons for a burner not to fire.\015\012\015\012Here is a link to a troubleshooting guide for hot water pressure washers.\015\012\015\012 ... Pressure Washers

North Star pressure washer will not ignite the burner. It is full of diesel fuel and you can here it clicking like it is trying to light but will not.


... Pressure Washers

Dish Washer, Model GLDL560N1055, S/NAR 808556B. Dishes and other items are not drying. They are still wet not damp. Brochure says try "Hot Start,Hot Wash or Added Heat options. Do I use Hot Start and Hot Wash at same time? Why must I use options rather then the normal control? I purchased 7 addtional GE appliances, recently, and Dish Washer only problem.


... GE Dishwashers

I have a washer model 1805 (1800 PSI). Everything works but there is always leaking of water (sprays) when I use it. The leak is not from where the water hose connects to the washer, but where the black piece attached to the hose is connected to the body of the washer. I can still do a decent job of power washing, but am wondering if the leaking of water is reducing the power of the washer.


Yes, leaking water will reduce the pressure. Sounds like you need to replace the O-Ring inside the connections on the pump. This is where the pressure hose connects to the pump. If you look carefully inside that connection you will see an O-Ring. Use ... Campbell Hausfeld PW1805 1800 PSI 15 GPM Pressure Washer

I have a Karcher K3.48M electric pressure washer which used to shut off when you weren't using the cleaning wand. This no longer happens and there is alot of water running out of the bottom of the unit. (This didn't used ot be the case) I expect a leak somewhere inside the unit, but I'm wondering even more if there is a pressure switch which has failed that cased the leak. In other words, if I find and repair the leak and there is a failed pressure switch, it will likely only break again. I can'


Hi you will have a 8 digit number on a silver plate on the machine with a number like 1.141-470.0\015\012Then go to www.karcher.com then on the left click on Europe, then you ... Karcher PSI Electric Pressure Washer

Briggs and Stratton pressure washer fuel leak


You've hit the nail on the head.The float,needle and seat are stuck wide open.Once the carburetor bowl is full of fuel the float rises up on top which pushes the needle back into the seat shutting of the flow of fuel.As the engine consumes that fuel ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Northstar Hot Water Pressure Washer (model #157322) While using the pressure washer the safety relief valve activated venting steam and hot water from it... I immediately shut it down and let it cool down. After it was cool, I turned on the water supply again and the relief valve was still spewing water from it. My neighbor said it was probably the "unloader" valve was stuck or damaged. I called around my area and it seems as though no one services my pressure washer.. Is there a manu


... Pressure Washers

I have a excell 2500 psi max honda 5.5 ho vr2522 2.2 gpm presser washer and has been stored for about a year, still looks brand new and has only been used twice before, it has oil and was stored with no gas in the tank, i put fresh gas in the tank and blead the fuel bowl until fuel ran out like it should, the washer wont start, ive checked the turn on switch as well and the fuel cut off knob, i spayed gas in the carb and it fired up but stopped running as fast as it began to run, its not getting


... Honda Black Max 2600 PSI Pressure Washer

GOT A KARCHER HDS755 BUT THE BURNER DOES NOT WORK.IT HAS FUEL GOING TO THE NOZZLE AND HEAPS OF SPARK.WHEN I OPERATE THE MACHINE WITH THE BURNER SWITCH ON AND FUEL LINE DISCONNECTE FROM NOZZLE,MACHINE WORKS FINE WITHOUT HOT WATER.WHEN RE CONNECTED,THE MACHINE WANTS TO CUT OUT.


Hi Please check your oil zzle is not blocked at all. Remove the burner head and renew the nozzle. If that fails you will need to check the fuel pressure from your fuel punmp which should be at least 9-10 bar. ... Pressure Washers

North star eletric hot 2000 psi 3.5 gal per min oil pump had blown shaft seal. replaced with new pump. put small allen plug in return port. I have oil flow to the pump but none comes out port leading to burner even with shutoff switch removed and pump turning. Installed test gage 0 pressure. Took off bypass line and ran into can. pumps small amount of fuel into can that way but with uneven flow & small bubbles. nomatter what I do I just can't get fuel outlet port to burner. pump # A2VA-7116 pl


... Northstar Pressure Washers

We have a Landa with a diesel burner. The problem


There is a screen in the tip of the spray nozzle for the diesel. Remove the tip and clean the screen. Your getting a explosion because diesel is pooling in the coils and igniting when conditions are right (air/fuel mixture). There is also a screen ... Pressure Washers

I have a Craftsman 2700 psi pressure washer with a Briggs and Stratton 850 engine (80 year anniversary special addition) . It is about 2 years old and used very little and will not start. I filled it with fresh fuel and checked the oil. I also replaced the spark plug and air filter. I checked the fuel line thinking it may not be getting fuel, but there is no obstruction from the tank to the end of the fuel line. I am out of TS options short of taking it to a service center.


Here is the long answer with everything we learned while using a power \015\012washer twice a day for years::\015\012It sounds like could be one of the problems listed below or a \015\012combination of those things.\015\012\015\0121 ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Rockworth Powertask Pressure Washer : model no AROW4P seems to rev flat out, hav to put choke in middle to use so not to fast revs. Im sure it used to rev higher and lower according to use of lance. could it be something to do with 3 valve things if so how could i tell if ok. put clean fuel in. oil level ok.another problem is when switched on water comes straight through lance,trigger makes no diffrence. please help


... Pressure Washers

Smeg DWF612WH dishwasher has developed a leak. Water comes out of the rectangular hole on the side of the water softner used to mount what looks like a level or pressure switch. A few seconds after the fill valve opens water leaks out, not a lot just a small trickle. After the washer has filled and goes ito its cycle, it does not leak again. Over the past weeks the problem has got progressively worse.


... Smeg 24 in. DWF612WH Free-standing Dishwasher

I have just bought a Kenwood KID60S10 dishwasher. I have used it a couple of times with no problem. However I realised it has been leaking from the water pipe at the back so pulled the unit out to tighten and readjust the pipe. However when I tried to run a cycle it won't after this to check if it was still leaking it won't. When I choose a programme non of the lights light up (except the power on/off light). I had left the washer out of the cavity to ensure the pipe wasn't leaking anymore. It i


... Dishwashers

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th


... Kenmore Dishwashers

Leaking input to the top of the dishwasher. Pollypro pipe comes up the back and into the top centre of the machine.... This is squirting out water when on wash cycle. Have undone large plastic nut on iside.. that has rubber washer on it... but the input pipe does not seem to have a washer between this and the steel body of the machine... this seems to be causing the water to squirt out... please let me know whether the washer has disintergrated or whether I need to use some bedding compound t


\015\012By reading Your problem most probably due to disintegration of washer only. Try with new Washer \015\012\015\0121. First try to adhere some wax or gumming material where washer is distingrated...if it solves u r probl ... Dishwashers

Had the Northstar 3000 psi Pressure Washer for 2 months and it started leaking oil from the pump during use. Took it to Northern and they are replacing the pump under warranty but said it was likely because I was using quick connects on my garden hose coupling and that was restricting the water flow making the pump overheat. They said never to use quick connects on the garden hose unless the opening is at least 5/8". Does anyone make such a quick connect? I hate having to screw the garden hose o


It is easy to check if your hose and quick connects are supplying enough water to the pump. Your pressure washer gallon per minuite requirements are printed on the machine and also on the pressure tips in GPM. Your post indicates 2.5 gpm but check yo ... Northstar Pressure Washer 3000 PSI

I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new


Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1423 seconds