Having problems with your Siemens 24 in. SL34A006UC Built-in Dishwasher ?

Does not stop running

\015 Hi, I have a siemens dishwasher. I have owned it for almost two years, and have never had a problem with it. I ran it last night before going to bed, and when i came downstairs this morning, it sounded like it was still running. I opened it, and there was a motor still running in the bottom of it. I turned it off and then back on and ran it for a cycle. When it was done, the motor was still running. Any ideas?\015

Answers :

I received this from GWOL... and it corrected my problem.
\015\012Typically this means that there has been a water leak of some sort and there is water in the lower base pan. This is the large white plastic base that the dishwasher sits on.

If you remove the toe kick and look back past the fill valve on the extreme left side of the dishwasher about 6 to 8 inches from the front you will see a red stick that goes straight up and down. This is a mechanical linkage that activates the drain feature. Be careful as there are live connections here.

This stick rests on a round piece of Styrofoam that acts as a float. If there is water present it will cause the stick to lift and the dishwasher will go into drain. The source of the leak will have to be isolated and corrected. Most likely it is the fill float assembly as referenced at the end of this post.

If the stick is not in the upright position then there is possibly an issue with the switch mechanism itself.

You will have to pull the dishwasher out from beneath the cabinet and remove the panel covering the left hand side. If it is a full panel then there are a couple of screws holding it on from the front through side trim as viewed when the door is open if it is a half panel then it can be removed by removing the large torx screw on the lower right as seen when facing the panel.

If there is a problem with the switch then the entire mechanism should be replaced.

Try the following link to a picture for reference. It is upside down as compared to the installed one:

http://www.repairclinic.com/SmartSearch/SSPartDetail.aspx?PartID=935595&PPStack=1
Hi,
\015\012 I had a problem with a clog in our garbage disposal drain pipe. The pipe was cleared up but subsequently the dishwasher is not functioning. When the door is opened and the on/off button is pushed the motor automatically starts running without a cycle being selected. Also, there doesn't seem to be any water getting into the washer. It is a siemens SL84A302UC-01 It was working perfectly the day before. Can you help me?
\015\012 Thanks
Repair Help & Product Troubleshooting for Siemens 24 in. SL34A006UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

ASKO 1555 dishwasher won't run. The anti flood device motor won't stop running but we've removed all the water. All the lights on the front panel blink in unison and when we hold down the start/cancel button on the front, nothing resets. We can't run our dishwasher. We've tried disconnecting power and resetting the circuit breaker but the churning motor won't stop.


Hello,Welcome to FixYa.Based on your description " The anti flood device motor won\\'t stop running but we\\'ve removed all the water " It is likely nothing very serious. ... Asko 24 in. 1805 Built-in Dishwasher

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

We have an Asco type DW 95.5 built-in, model 1885. During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric still runs. When I pop the circuit breaker, all is stopped. However, when power is restored, the lights and code flash as above, and, again, something electric runs. My email: [email protected] Thanks for any help...


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your description " During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric s ... Asko Dishwashers

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

Runs for a few minutes then stops and the program and top right light flash, if i press the power button off then on it runs again for a while then stops again with the flashing lights.


The electronic portion of the dishwasher is going bad. Could be a resister or any other issue..I would check with the manufacture Tech support they will advise you what your options are. ... Zanussi Dishwashers

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Miele G 870 SC dishwasher had blocked drainage due to stopped up sewer which got snaked out by plumber. Ever since, the drain pump won't stop running. Have cleared the trap, filter, and drain-filter and still the pump runs continuously.


Hi\015\012\015\012The problem is with the float switch mechanism located at\015\012the bottom of the unit...either this has gone bad and should be replaced or the\015\012pump itself is bad & should be checked. Hope this helps...please pos ... Miele 24 in. G870 Built-in Dishwasher

Candy a8001/1 uk the dishwasher fills and runs for 10 mins then stops. the heating element is heating ok and i have checked the door switch and it seems to be functioning ok but if i open and close the door it will run for a couple of secounds and stop again could you tell me what could be the cause of this?


... Candy Dishwashers

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Bosch (SHU5302UC/U12). The washer often takes 2 or more hours to run. Sometimes it gets stuck for a long time part way through (e.g. just sits at "43"). Other times, it gets stuck at 1 and won't stop on its own. The latest thing is 2 dots have appeared on the display that I've never seen before. For example, instead of "43", it reads "4.3." Eventually it gets to "C.L." but does not stop running. Also, its been making very strange noises during part of the wash cycle.


... Bosch 24 in. SHU43 Built-in Dishwasher

My garbage disposal had something stuck in it. i did not know and the sink was backed up. i started the dishwasher and it sounded like the motor was running like a drain emptying...i thought it would stop but continued. i unplugged the dishwasher, freed the garbage disposal and the drain is now clear. i turned on the dishwasher and the sound is the same. the large POT light is lit up and when you try to shut it off it doesnt stop running. i unplugged it for fear of breaking something. HEL


Hello,Welcome to FixYa.Based on your post, the ... Asko D3251HDSS Stainless Steel Built-in Dishwasher

Bosch Dishwasher Cycles will not stop running. They keep starting over. Help please!! Our 2 year old dishwasher will not stop running. It gets to the end of the cycle and starts over again. Plus, the cycles seem to have gotten longer. We called the Bosch repair number and they want $150 in cash to come out and look at it. Then they will come out and fix it!!!! Unbelievable!!!


Carry out a reset.\015\012This should reset the board back to factory settings,\015\012Deep Diver ... Bosch 24 in. SHU5305UC Built-in Dishwasher

My dishwasher has stopped mid cycle showing 1 minute left , when stopped and started again it now shows 28 minutes contantly, plus it continues to run (ie pump running) after the door is open. Any ideas ? many thanks Doug


Hey dcp667\015\012\015\012Dishwashers are incredibly durable machines. They can take years of daily use and in many cases, it's only a change in decor that brings about a replacement. Of course that doesn't mean things never go wrong with ... Dishwashers

Kew power washer,model Alto Force E. Will run for about ten minutes, then stop, often for days. Appears to run on two settings - occasionally gives bursts of real power, then reverts to adequate. Stops shortly after wards


... Pressure Washers

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Stopped running dishwasher was running and stopped in mid-cycle. will not turn back on


... Whirlpool 24 in. DU800CWD Built-in Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

John deere's 3000 psi pressure stops after running for 3 to 5 minutes. Then wait for at least 10 to 15 minutes to try to restart it. Then it runs for 3 to 5 minutes and stop.


This sounds like the bypass valve is sticking. It needs to be lubed with a VERY good waterproof grease. ... Psi Pressure Washers

Our dishwasher came with our house. Brand new. It is 2 yrs old now, warranty gone. The problem is when you shut the door the machine starts running immediately and keeps running and running and running. You can push the stop button, delay button and it still runs. Also, doesn't clean. model# FDB1050REC4


... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a Honda GC160 5 horsepower power washer with 2400 psi. When its cold it is easy to start but after it has been running for a while the only way to start it is to have the water shooting out of the wand. Once it is hot and running if i stop the stream of water (release the trigger on the wand) then the machine shuts off. It seems like the only way to keep it running is to constantly have water running through the wand. Please help


... Pressure Washers

It starts running then stops - starts pumping in water then stops, etc. burning plastic smell near top... doesn't leak, gets power, but begins to fill, then stops - might start to drain (pump), but then that stops too...


... Frigidaire 24 in. PLD2850 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0709 seconds