Having problems with your Siemens 24 in. SL34A006UC Built-in Dishwasher ?

Heating failure Bosch Siemens 654120.21.01

\015 GV 630 450 V1\015

Answers :

Repair Help & Product Troubleshooting for Siemens 24 in. SL34A006UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Heating failure Bosch Siemens 654120.21.01


... Siemens 24 in. SL34A006UC Built-in Dishwasher

My Bosch SHY66 does not heat the water. How can I differentially diagnose the heater being the problem from the problem being a failure of the thermal switch?


... Bosch Dishwashers

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

Bosch Dishwasher I currently own a Bosch dishwasher. One of the selling points, if I'm remembering right, of the dishwasher was it was supposed to super heat the hot water that is coming in from the tap. I have 3 problems. We have to rinse the dishes by hand before putting them in the dishwasher, Otherwise they won't come out clean. The dishwasher will run for four hours sometimes longer. It doesn't seem like it is heating the water any hotter than what comes out of the tap.


Your control board is bad. ... Bosch 24 in. SHU43 Built-in Dishwasher

Hi I have a Zanussi ZDF501 dishwasher that stopped heating up intermittently. It got worse and I fitted a new heater and all was ok for a few months. Then the intermittent failure started again. Note that I tested the old heater and it is actually OK without a short circuit so I don't think it was the problem adn can be re-used. Could it be the thermostat or heat sensor? I am concerned it might be the PCB since the failure was intermittent. Thanks Dave


In my case, although the solder joints on the relay looked poor, improving them didn't help. I had to replace the relay. Fortunately, Maplin stock a compatible one, JM67X for 1.99. See ... Zanussi Dishwashers

Dead spot? We just moved into a house and the built-in frigidaire oven, model no: CFEB27S2AS1 bakes on only the low heats, 0 - 250 and high heats, 450 - max but does not heat (red indicater light not come on nor any heat) at mid-range. Is there something I am not doing, or does it need to be "rebooted", and if so how do I get to the power plug/switch as it is embedded in the wall?


Hello\015\012\015\012You said, We just moved into a house and the built-in frigidaire oven, model no:\015\012CFEB27S2AS1 bakes on only the low heats, 0 - 250 and high heats, 450 -\015\012max but does not heat (red indicator light not come ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a Bosch DLX series dishwasher and no manual. The heat dry doesn't work or at least not well. There is no heat on/off switch. How do I ensure the heat is on so I can stop drying my dishes by hand?


... Bosch Dishwashers

Bosch dishwasher shx46b02uc has stopped drying. Per online comments, they seem to point to either a corroded wire or a bad heating element. We've replaced the heating element and all the wires looks fine. All other functions work - just not the heat. Open to suggestions.


Hello,Welcome to FixYa.Based on your description ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

The original control unit from Bosch' dishwasher SHU4302UC/14 has been replaced after recall from Bosch with a new one that stop working after three washes. It does not respond to any command and shows ''0'' at display. What may be the problem?


... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Bosch Classixx SGS43CO2GB which is working but not heating the water or drying? Is this something I can fix myself, and if so where could I get another heating element? THanks


... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a bosch she44c05uc dishwasher that get stuck on 1 and won't finish. The water will pump out when I cancel. The water will pump in but won't heat up. The final heating doesn't seem to work also. I have removed the circuit board and there appears to be NO solder issues. What else can it be?


... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher

The dishwasher takes water in (not to much as when you open the door later, there is hardly water visible) and then it sounds as if it is busy heating the water. Then all of a suddden it will trip the power switch on the distribution board. My impression is that it is not takingin enough water and the heating part causes the trip failure. Your comments and advice to resolve will be aapreciated. Planning to open it up this weekend (machine not that old)


Usually ,there will be a float in the bottom of a dishwasher that shuts down the waterflow when it has received enough water. it works just like the float in a toilet tank (if you are familiar with that) you are definitely on the correct path in thin ... Indesit Dishwashers

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

I have a Bosch SHE56C05UC/40. The unit fills and drains ok but the circulation pump will not operate. I run the diagnosis according to another of you posts and came with an error code E1 which is a heating code. Why would this prevent the pump from running? Your diagram show a flow switch in the heating circuit which won't close unless the pump runs. A diagram of the pump circuit would helllllp.


Follow the instruction code in your ins.manual if you do not have go for free download : www. fitness.manualsonline.com or www.ret ... Bosch SHE56C02UC / SHE56C06UC Dishwasher

Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.


Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers

Bosch dishwasher i have dishwasher that seems to progress to fast through cycle and does not heat water leaving dishes dirty. Is it likely to be timer unit or heating element Thanks


I'm probably sounding like a broken record, but id f its got buttons on the front and not a knob, its probably the control board. Unplug the unit or flip the breaker.Take off the outer door and the control panel by removing all those torx screws down ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

Failure with control unit or heating elemint failure


Hi,Check your heating element.. http://www.fixya.com/support/r4589033-dishwasher_problems_heating_element_not ... Baumatic 23 in. BDW5 Built-in Dishwasher

Hiya, I have a Bosch Dishwasher SGV4313GB that wont heat the water, it gets stuck with cold water continually washing (pre wash??) the delf. Its a built in and I have opened the inside metal panel and exposed the control unit (PCB) there is no blackened/loose soldered joint to be resoldered. I am at a loss as to what else in the heating circuit to look for. Can you point me in the direction of what I should look for next? Kind regards Mark


... Bosch Dishwashers

Bosch dishwasher heating element will not heat up


... Bosch Dishwashers

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

My dishwasher does not do a hot wash. Why is this? If I need to replace the heating element, how do i gain access to heating element on my Bosch classixx dishwasher?


Hi, a common problem with these machines is the solder coming away from the heater relay. A simple repair if your lucky. Run a continuity test on the element with a multimeter before replacing it, as it is a massive job to change it. I just changed m ... Bosch SHU9950 Dishwasher

Bosch Dishwasher SMS4602eu is not heating up. I have tested the heating element for continuity and this seems to be fine. Any other suggestions would be greatly appreciated?


... Bosch SMS63E Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0721 seconds