Having problems with your Siemens 24 in. SL84A302UC Built-in Dishwasher ?

On last run, did not finish cycle (no final drain) but began a loud rhythmic clicking (from controller area) that stopped after several minutes. Now, no response at controller buttons--no lights/power. This machine is about 5 yrs old and has run perfectly up to this point.


Answers :

The front panel control board has got short internally.the control board needs replacement.but in the control board section there is a minute fuse located if that fuse blows you will not get light on control board.replacing the fuse will make it work.but it has to be checked first whether its just the fuse of whole front panel control board.\015\012you can check the fuse by continuity tester.you will get required parts at \015\012www.repairclinic.com or also from www.partselect.com\015\012
\015\012This will help. Thanks please keep\015\012updated.please do rate the solution positively .thank you for using fixya
Repair Help & Product Troubleshooting for Siemens 24 in. SL84A302UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On last run, did not finish cycle (no final drain) but began a loud rhythmic clicking (from controller area) that stopped after several minutes. Now, no response at controller buttons--no lights/power. This machine is about 5 yrs old and has run perfectly up to this point.


The front panel control board has got short internally.the control board needs replacement.but in the control board section there is a minute fuse located if that fuse blows you will not get light on control board.replacing the fuse will make it work ... Siemens 24 in. SL84A302UC Built-in Dishwasher

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

Kenmore Ultra Wash dishwasher model number 665.1374 or 665.1384 I am a technician. This unit does nothing. It has power and ground. I have tested the door switches. They test good. If I unplug the unit and plug it back in then it will run a drain cycle, at least that is what I think it is doing. The motor runs for about 4 minutes. Once it shuts off, there is no further response. No control indicators illuminate. No response from pushing any of the touch buttons.


... Dishwashers

Smasungdishwasher DMT610RHS error codeCE showsup. eventhough the is not locked in, it still runs with error code CE, but the water is not coming in. but the motor is running. unless I plugged out, it keeps running. I shut off, but not responding power ONOFF.no response to any button on the control pannel. but keeps running.


... Samsung Dishwashers

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

Dishwasher will suddenly start "beeping" intermittently at several second intervals when not in use. Controls will not funtion at times, then will suddenly be OK, and run through a full cycle perfectly. Later will do the same all over again. I have replaced sequence switch, but no improvement. Does it need a control panel, and if so, should original sequence switch be OK?


HI. That original sequence switch shoudl be ok. This will essentially be a control panel issue. There may be one or two button circuits that could have become unstable,thus, causing the intermittent beeping. With that said, i would like to examine th ... GE Dishwashers

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

Regarding Maytag Dishwasher, model # mdb4651aww3. Most of the lights on the control panel will not light up. You can't change cycles or set the delay timer etc. You can hit the start button and it runs a perfect cycle, and ends up with clean dishes. You just have no idea what cycle it runs.


I have same problem with my Maytag. Had a repair guy come out and he said it's the 'controller card', not the button touchpanel. The controller card is $127 and not in stock and there's a 'several month wait'. I'm not going to wait, going to buy ... Maytag 24 in. MDB4651A Built-in Dishwasher

1998 KitchenAid Dishwasher model KUDM24SEWH2 - cycle and start buttons light up, but once the water has finished running the machine does not start, but "tries" to start every 20-30 seconds. Selecting Cancel provides the same results. Do I need to replace the control panel? Thanks! Stephen


... Dishwashers

Dishwasher control buttons do not work. Machine is stuck on low wash and headed dry. Pushing butttons on crontrol panel do nothing. Dishwasher seems to work, fills with water , you can here it run it's water agitation, and drains, but only works in low wash


Hello,This means the touch pad has failed, you can make this repair it's simple. Try flipping the breaker off for several minutes this may reset the glitch.Applian ... Dishwashers

ADP6000WH/ADP6000IX Whirlpool Dishwasher. The controls are not working correctly. When I select the top two (Strong and Normal) settings I hit the start button the dishwasher will not run. When I select the other four (Economy, Rinse, glass and soak) settings the machine works fine. Thanks MB


... Whirlpool Dishwashers

I don't have the model number here but it is the machine with the three control buttons on the front of the door. It seems to have lost its programming. It will start and do the initial small flushing wash. The pump runs. But it never seems to do the actual washing cycle. The dishes, although wet, are not clean. Yours truly, Brian Felske email [email protected]


... Dishwashers

I have a maytag dishwasher mdb5601awb. when I hit the start button nothing happens. I have found the instructions to do a manual test which is hitting the heated dry button 5 times and then the start button. Thinking it will run some test which I have no idea what to look for, it actually runs the machine's wash cycles and clean, dries and tells me it clean with the green light goes on. How do I reset/reboot the machine so it starts by just hitting the start button again?


... Maytag Dishwashers

Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

I can't get my electrolux dishwasher to run. It seems as though the touch pad is not responsive. It says to reset holding down the sanitize button, I do that it beeps but doesn't do anythng. All of the buttons are not lit up. I have to hold the delay start button along with the sanitize button to light the buttons up, still the buttons don't seem to be responsive, I touch the start and the lights go away and flashing numbers appear. Et 19 66 02 34 Any help would be appreciated.


... Electrolux EIDW6405HT Builtin Dishwasher

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

Start button keeps flashing machine will not run on any program. I've tried holding down the start and time button which in the past has allowed me to restart the machine. This isn't working this time


... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Our dishwasher came with our house. Brand new. It is 2 yrs old now, warranty gone. The problem is when you shut the door the machine starts running immediately and keeps running and running and running. You can push the stop button, delay button and it still runs. Also, doesn't clean. model# FDB1050REC4


... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

Maytag quiet series 200 model MD88750AWB Dishwasher doesn't work. Control panel only responds to the heavy wash button. When pressed it lights up along with three option lights. After about 10 seconds they go off. There is no mechanical response to the pushed button. There were no symptoms leading up to this problem. If you can give me a "head's up" about what to look for before I open up the control panel I would appreciate it. Thank You John


Hi\015\012\015\012\015\012\015\012\015\012\015\012If your dishwasher doesn't work at all, check these:\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is there power getting to the dishwasher? This can be difficu ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1132 seconds