Having problems with your Siemens 24 in. SL84A305UC Built-in Dishwasher ?

Dishwasher counts down to 1 then continues indefinately.


Answers :

Repair Help & Product Troubleshooting for Siemens 24 in. SL84A305UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher counts down to 1 then continues indefinately.


... Siemens 24 in. SL84A305UC Built-in Dishwasher

We have a Bosch dishwasher model SHU5315UC/U06. When we ran a "Regular Wash" the dishwasher ran continuously and the timer did not count-down. None of the Delicate or Rinse and Hold buttons responded. The only button that works is the "Scrub Wash", but when we ran it did the same thing. Ran continuously and the timer moved one minute after running about five minutes. I look forward to your solution. Thank you. Jerry


My father-in-law has a Bosch and they had the same problem. The tech guy said it was not heating properly and that caused it to continously run because it won't tick down the timer if it doesn't reach a certain temp, so try turning your faucet as hot ... Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Bosch Exxcel Dishwasher model SGS56E02GB/47 When you switch it on no water is coming through - what sounds like the pump/motor sounds a lot rougher than normal and there's a very very faint electrical burning smell. The timer counts down, but it never appears to do anything and continues doing so after the counter has zeroed.


... Bosch Dishwashers

Have a 665-16293201 dishwasher with electronic controls and smart sensor. Approx 10 years old in great shape. it just started having a problem - it takes a long time for the sensing to be completed at the start of a wash and then the washer will start and display a time - like 92 minutes - turn the sensing light off, then start to wash and count down. when it gets to 86 minutes, it starts to sense again and will continue washing while displaying 86 and with the sensing light on. It will keep


... Kenmore 24 in. 16293 Built-in Dishwasher

Timer stops count down at 1 minute remaining. Dishwasher continues to run.


Hello,\015\012\015\012The reason your dishwasher is displaying a "1" is the control has detected a heating error. Here`s why...\015\012\015\012The issue with your Bosch dishwasher likely lye`s within`the electroni ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Whirlpool dishwasher model# GU2451, two years old. On any cycle, it counts down to 44 and won't go any lower. It sounds like a motor is constantly running when it hits 44. It will continue like this until I shut off the machine. What needs to be fixed?


Hi,Go to the house breaker box and find the breaker for the dishwasher.Turn the power off form the box for 10 minutes and this will reset the system.This should usually clear any electronic glitches and enable you to start. ... Whirlpool Dishwashers

Kenmore elite dishwasher, 2003, won't count down during wash cycle past around 80, and just continues to wash (on any setting), and sensing light remains on - reset didn't help.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing ... Kenmore Dishwashers

I have a Bosch SHE46CO dishwasher that runs too long. It adds an extra 37 min to the normal wash cycle. It counts down correctly until about 50 min then it adds the 37 min. Also when it get to 1 min it continues to run for at least 15 min. I have cleaned the filter and the upper and lower arm.


It can be the software or anly have a much colder water and it needed a longer time to heat for washing and rinsing. also a heater is damaged and the dishwaser runing at the half capacyty. so long! ... Dishwashers

I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

I have a Bosch Dishwasher, Model SHE46C06UC. No mater what cycle I start it in, it simply activates the drain and continues to run without ever starting. Within the last week prior to the dishwasher not working, I noticed a low hum/vibration emitting from the dishwasher. I've clean out the screen and drain filter, removed the pump cover to check for any debris. I've manually added water and it does drain. Additionally, the drain cycle continues to operate even with the door open.


First thing you may want to check is the door switch. You can pull it off and measure the resistance with an ohmmeter. If you get good reading while pushed in and none while switch button is released, then it is a good start. Next, you may want ... Dishwashers

My asko dishwasher ran great until recently. after finishing a load, the pump just continues to run (even when all water has been pumped from the unit and it's running dry) and the display isn't flashing anything (not codes, etc). Worried about destroying the pump, I shut off the washer at the breaker, and it's been a few months since we've had a dishwasher. Every once in a while I'll turn the power on and it just continues doing the same thing - it's stuck in this position/state, so I have to s


The IC that controls the pump seems to have gone kaput. Change the IC. ... Dishwashers

Dishwasher keeps stopping and beeping continuously until I press the start button again and shows the F8 Code. When I press the start button it continues for about 5 minutes and then stops properly but there is lots of foam still in the bottom of the dishwasher.


Sir i think the problem would be in any of the three areas. any prob in these areas would lead to the problem u specified\015\012\015\012Test the timer motor.\015\012 ... Dishwashers

Hi - my Viking dishwasher has developed a problem where the pump runs continuously, whether the power switch is ON or OFF. After the power is turned ON, the troubleshooting guide indicates that there is too much water in the dishwasher. (One of the pot symbols on the display flashes continuously to show this indication.) I am unable to switch between programs, e.g., from quick rinse to pots & pans. I cleaned all the filters to no avail. I had to secure the circuit breaker in order to turn t


If you open the kick plate, you'll see the pan below the motor and check for leaks. The leaks will trigger the sensor to pump water out. Once you dry out the pan, the pump motor will stop and you should be able to reset the program. ... Viking DFUD042 Built-in Dishwasher

My dishwasher will not start. If you unplug it and plug it back in it says 1H, no matter what button you press it then says 2H and if you press another button it will say 3H until it runs through to 9H then will display --. It will continue to do this until you leave it alone and walk away. Then after a few moments it will clear itself out and the 'Normal' light under cycles will continue to blink. The dishwasher is 3 maybe 4 years old. Please help, I have a 3 year old and an 18 month o


Hi,There could be Few Possibilities.Let's try to Reset. 1h, 2H -----9H usually shows delay X hours Display where X would be 1,2...9.Turn the Power OFF for few minutes, say 5 Minutes and then Turn it ON. ... Dishwashers

Asko dishwasher Rotu emailed with some helpful info, so here is the additional you requested. The dishwasher continues to fill as long as the water is turned on to the appliance and then it will drain. For some reason this cycle continues. The repairman said it needed a new control board. Is this the case and is there anything else I can do?


You could have a bad fill valve that doesnt close. Try unplugging the unit or turning off the power at the cuircuit breaker. (not the power button) If it still fills when you turn on the water, it just has a bad fill valve. If it does not fill, take ... Asko D1776 Built-in Dishwasher

Our Bosch SHU43C06UC/17 dishwasher stopped working properly today. The power scrub cycle starts at 115 and counts down to 112 and then stalls -- no sounds of water entering the unit... no further counting down The regular cycle starts and shows 97 and counts down to 94 and stalls. no sounds of water... no further counting down. We hear a constant buzzing sound. Can you help?


... Bosch Dishwashers

The dishwasher will start to cycle. I can hear the water begin to run. I hear a click and at the time the dishwasher should start to run the cleaning cycle. During the cleaning cycle the dishwasher will stop working. The dishwasher is silent. The timer will continue and the water will drain out at the appropriate time.


This is probably okay, you have clock like motions running the motor electric contacts. There needs to be a delay between some cycles or shorting will occur. The motor on some designs, for example. is reversed to pump out water. to have this work lon ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

I have a SHU3032UC BOSH Dishwasher for a couple of years now. Always worked as expected. Latetly, the dishwasher never stops. It looks stuck on an "unknown cycle"... The cycle dial stays at the "bottom" cycle (there's nothing written). If I turn it 1-2 "clicks", the dishwasher continues its work and ultimatly finishes with very good cleaning results. Once, I open the dishwasher when it was stuck in the "bottom" position, and there was hot watter at the bottom. Here's what I've tried so


Hello, welcome to FixYa.\015\012\015\012Based on you description of the timer not advancing I suspect the thermostat isn't satisfied when heating the water.\015\012\015\012The SHU 30** unit`s with a mechanical timer have very few if any, issues with ... Dishwashers

Maytag MDBH965AWQ I have a Maytag dishwasher model number MDBH965AWQ. A few weeks ago the clean and sanitized lights would not go off after the door had been left open for over 30 seconds. Then last week, the diswasher would shut off in mid cycle and all lights would turn off with water still in the dishwasher. Today, I noticed that I am able to open the dishwasher door while the dishwasher is running and it will continue to run like the door was never opened. Now it is starting to trip the brea


2 items in need of testing are the door switch - and the main controller board/timer unit.CLIC ... Maytag 24 in. MDBH965AW Built-in Dishwasher

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???


Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers

My SHE4402UC/36 dishwasher malfunctioned all the lights were flashing and the machine was trying to drain. The guy came out and replace the control board. The dishwasher now read 199 on all cycles except the rinse and hold, the santitized light does not come when its done. The repair guy told me the count down timers were flakey on the the Bosch dishwashers and it would learn my dishwashing patterns in time. So 6 cycles later the dishes are still damp at the end of the cycle-the length of the cy


Well its not baloney but it is cheesey. normally changing the module is the cure but it has to be programmed correctly. bosch has a recall so check it out and see because the recall is free and the tech is suppose to know how to program it. go to the ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Dishwasher doesn't finish washing cycle. Or doesn't switch to rinse. Stack half way through the program, continuously running


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1507 seconds