Having problems with your Simpson Pressure Washers ?

How do I remove wheel? from pressure washer? - Simpson Pressure Washers


Answers :

You first have to pry the cap off the wheel with a screwdriver then under the cap there should be either a pin which you pry off or a nut which you loosen.
Actually, after you remove the cap, you will find a retainer with multiple flanges that holds the entire wheel assembly on the axle. I used a screwdriver to make enough space to get a small wheel puller under it and it slid right off. Then I slid the wheel assembly off and replaced the wheel. The whole process took about ten minutes.
Repair Help & Product Troubleshooting for Simpson Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I remove wheel? from pressure washer? - Simpson Pressure Washers


You first have to pry the cap off the wheel with a screwdriver then under the cap there should be either a pin which you pry off or a nut which you loosen. ... Simpson Pressure Washers

Simpson pressure washer winterize - Simpson PS3200 Powershot 3200 Psi Direct Drive Cold Water Gas Powered Pressure Washer W/ Honda Engine


... Simpson PS3200 Powershot 3200 Psi Direct Drive Cold Water Gas Powered Pressure Washer W/ Honda Engine

I have a Husky gasoline pressure washer. The honda motor starts but stalls because the pressure by-pass (not the right term) doesn't seem to open and builds up pressure. I haven't tried to remove any parts yet. I think grit has got in but don't know for sure. The pump looks pretty simple and the part I want to remove for cleaning looks like a plastic hexagon nob. Will this access the by-pass or is it something else.


I think you're right about the knob, but try this:Open the water to the washer. Leave the line open, and hold the trigger down to get all of the air out of the supply and discharge lines. While still holding the trigger down on the spray gun, ... Pressure Washers

I have a Craftsman pressure washer model 580.752020. I ordered a pressure hose according to the manuals parts list (203961GS) but does not match the original hose I removed from the washer. A hose #31


... Craftsman Pressure Washers

How to install new wheel on Simoniz S1600 pressure washer


... Pressure Washers

How to remove pump from pressure washer - PowerStroke 1700 PSI Electric Pressure Washer PS171433D


If motor has great compression you should get 2200 psi ... PowerStroke 1700 PSI Electric Pressure Washer PS171433D

Removing pressure washer wand - Karcher Pressure Washers


... Karcher Pressure Washers

Owner manual msv2700 simpson pressure washer - Pressure Washers


... Pressure Washers

The last time I used the pressure washer was running fine. A few minutes later I tried to start it up and could barely turn it over. I removed the recoil and could turn it a little easier backwards. The motor is a Honda GC190 on a karcher pressure washer and has 20 -30 hours of running time. Thanks Clint


... Karcher 2500 PSI Pressure Washer

How to remove tire from pressure washer - Honda Pressure Washer PSI 3000


... Honda Pressure Washer PSI 3000

I have a Challenge Xtreme 1800w Upright High Pressure Washer. The proplem is fluctation in water pressure,this even happens when all hoses are removed so the pressure is coming straight from this pump.the vonly way I can describe it is as if it is "hunting"ie high pressure then a ver short pause then back to high pressure. thank you for any advice you can give me with this proplem,also can you recommend a more suitanble machine for home use. Regards M rA C O'Meara


... Pressure Washers

I have a 2.5 gpm model K2400HH pressure washer that won't sprey with high pressure, it started intermitanly, now won't spray high pressure at all. Last year I removed the valve and cleaned it and put white lithium greese on it and it worked pretty well for a while, but now no high pressure.


I would suggest purchasing a new revised unloader valve, here is the link to purchase one ... Karcher G2650HHR Gas Pressure Washer

Poor pressure karcher g 2500 pressure washer with a 5.5 honda engine. No high pressure, hose pulsates as does water out of the outlet. have removed the unloader valve twice and cleaned it to no avail


I had this same problem on my pressure washer.the pump had some broken parts in it .i found my replacement pump on EBay. ... Karcher 2500 PSI Pressure Washer

Not much pressure, pressure varies greatly - Simpson Mega Shot Gas Pressure Washer


... Simpson Mega Shot Gas Pressure Washer

Have whirlpool dishwasher model DU1055XTSS2 and the top rack water wheel does not spin. Operated the washer with door opened and it gets water but doesn't spin. There are no restrictions to the jets on wheel and the wheel turns feeely. The only thing i can figure is inadequate water pressure....


... Dishwashers

I have a ANNOVI pressure washer and I can not seam to get the engine apart from the pressure pump. All bolts are removed and the bludy thing will not come apart. The lock nut on the drive is not even


There may be no good news for you. Once those hollow shaft pumps seize to a engine shaft, they can be real buggers. In fact, they can be impossible. But before you give up and completely destroy the pump to remove it from the shaft -- the ... Pressure Washers

SIMPSON MSV3024 PRESSURE WASHER


... Pressure Washers

I have a Frigidaire dishwasher, FDB-1100RHC, that is not cleaning dishes. My fiance cleaned the trap at the bottom of the washer, removing both the small basket and the larger mesh grid. After replacing both, the washer doesn't seem to have enough water pressure to spin the lower and/or upper arms. If I interrupt a cycle and open the door, water is dribbling out of the upper arms, but they are not rotating and do not move from whatever position you place them in. Both arms are completely uno


Hello :)don't feel bad, I run into this kind of problem at least once a week.\015\012It does sound like the pressure isn't there so you're not getting water to the upper spray arm. What you need to do is take the pump apart, which i ... Frigidaire Dishwashers

Simpson mega shot 3000 manual - Simpson Mega Shot Premium Gas Pressure Washer


... Simpson Mega Shot Premium Gas Pressure Washer

I just purchased a Simpson Megashot V3000 Pressure Washer and noticed the engine would stop running every time I released the wand trigger. Also, water was constantly spraying out of a valve underneath the unit - I assume it's some type of pressure release valve but there is no mention of it in the owners manual. I am thinking about returning it to Costco for a refund.


... Simpson Pressure Washers

Hi there I have a Bosch SGV4313GB/17 Dishwasher the problem is there insuffient water pressure to feed the washer arm and they are not rotating Ihave cleaned the arms and circulation pump impeller with white vinegar ,I have also overriden the door switch and operated the dishwasher with arms removed and the circulation pump seem to be working but with insuffient pressure also the machine does not fill to the depth it did when it was fine! How does one tell if it is the impeller or the


Ours is a SHU3300UC/06 model, basic model which we bought in 1999 so have had 9 years of trouble free service.Recently\015\012we noticed that there was soap left in the soap dispenser after the\015\012machine had finished all the cycles. On fu ... Dishwashers

At the beginning the pressure washer was running but there was no power from the nozzle. I stop the gun trigger, remove the nozzle , it works for 1 minute and stop working again Now the washher pressure turns off on its own after 1 minute or less Honda 2400 psi


See attached link:\015\012http://www.wmpcs.com/index.php?main_page=page&id=14\015\012\015\012If you continue to have the problem you m ... Honda Karcher G2400HH-R Pressure Washer

No water pressure - Simpson WB4200 Water Blaster 4200 Psi Cold Water Gas Powered Pressure Washer W/ Honda Engine


... Simpson WB4200 Water Blaster 4200 Psi Cold Water Gas Powered Pressure Washer W/ Honda Engine

Pressure washer does not discharge water under pressure until the nozzle has been removed from the lance- press switch and release, refit nozzle and then the water is discharged. Will switch off but does not activate next time.


... Pressure Washers

My pump is gone on my pressure washer. The honda engine is GC 160. The pump is a model VRX2527G. How do I pull the pump off the engine to replace it. I removed the four bolts from the pump housing, but the pump is still tight to the shaft. Please explain the removal process.


Hello,Your pump sits on a keyed shaft, versus a taper fit. This is good, since tapered shafts will require a puller to remove the pump.Since the pump is already bad, you have a few options available to you. 1) W ... Honda Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0797 seconds