Having problems with your Simpson Pressure Washers ?

Want rebuild kit or replace pump

\015 Model number on pump is an DD 2700 SHS The part number for the pump is 8000209\015

Answers :

Repair Help & Product Troubleshooting for Simpson Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Want rebuild kit or replace pump


... Simpson Pressure Washers

I'm in Afghanistan with a MI-T-M GH-3504-OEGH. We lost pressure from the pump. One: I'm looking for a manual for this Pressure Washer. TWO: Seal kit to fix the problem. I know they need to be high pressure seals or O-rings so I don't want to do a quick fix leaving us to rebuilding the pump again


... Mi T M Mitm 3500 Psi Hotcold Portable Gas Pressure Washer

Karcher 2400 pressure washer with honda engine. my problem is that i've installed a new rebuild kit in the pressure pump assembly, and now, when i reinstall the assembly back on the engine, i cant even pull start the engine over. its too tight! when i loosen back on the pump assembly, i'm able to pull the engine over. what have i installed wrong from the rebuild kit??


The pump is correctly oiled and lined up on the camshaft, correct? ... Karcher 2500 PSI Pressure Washer

I have a sears pressure washer, model 580752300. The pump on the underside vibrated lose and broke a couple screws. It came off and the oil drained out. I replaced the screws and it's ready to go except I can't find out how much replacement oil to put back in. Sears has larger containers but won't tell you how much oil to put in. However, there's a pricey pre-measured container they want to make you buy. Anybody know how much oil goes in that pump?


... FAIP Non Marking Pressure Washer Hose 4000 Psi, 50ft. Length

The unit fills up with water but the circulation pump wont turn on. if i jump the pump it works. the pump is connected to the timer board. is there any sensor that would cuase the timer board not to turn on the circulation pump. this unit seems to be manufactured by ASKO mod. DW20.3 i dont want to replace the board ($375.00) if not nessary. thank you


Hi\015\012\015\012\015\012Thanks for using FixYa. There is no sensor on your dishwasher for drainage purpose however, it uses a drain solenoid to open and close the dishwasher drain port. If this \015\012solenoid ... Dishwashers

Cat pressure washer pump rebuild kit - Caterpillar Cat Pump Pressure Washer Pump 3SP30G11


... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

I need a pump rebuild kit


... Karcher 2500 PSI Pressure Washer

Where can I get a rebuild kit for pump?model XR-2600.


Remove the pump and throw it away. Buy a better designed pump on eBay. just search your pressure washer model number or the obsolete rebuild kit part number a14292 you'll find the better pump. ... Honda Black Max 2600 PSI Pressure Washer

I am told the pump is defective and I was wanting to do the repair job myself. I need a manuel to take apart the machine to replace the pump assembly or clean it to see if that will do the trick. Is there a manuel so that I can do this maintance?


Usualy if pumps are difective are not worth repairing.\015\012log on to the manufacturar web site they should have a on line manual that might help you.\015\012good luck ... Frigidaire Dishwashers

I have a leaky gate valve shaft seal that I want to replace myself (part # WD8X181). It only leaks when in the drain cycle. Repair manuals are not available for this model. How much disassembly is involved to replace this seal? Do I need to gain access to the shaft from inside the housing pump assembly (drain sump)?


... GE Dishwashers

The model number I have is LD 1415ti doesnt want to pump any water but all other functions seem ok is this likely to mean a replacement pump?


... LG Dishwashers

Samsung dms 301trs dishwasher with e 3 error ? Tried to unblock but no blockages and the pump only works when it wants to and can be started by pushing with screwdriver. Does the pump need replacing


... Samsung Dishwashers

Have a leaky gate valve shaft seal that I want to replace myself (part # WD8X181). It only leaks when in the drain cycle. Repair manuals are not available for this model. How much disassembly is involved to replace this seal? Do I need to gain access to the shaft from inside the housing pump assembly (drain sump)?


... GE Dishwashers

We want to replace the pump to our DEWALT DP3750 pressure washer and can not ge tthe pump to come off the engine. how do you get it to come off?


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

How to rebuild the pump


Kit 1857 is the water pressure seal kit. 1856 is the piston oil seal kit. The head of the pump has to be removed first. There are 6 bolts, most likely "allen head". After they are removed, the manifold head will separate from the crank-case (the ... Annovi Reverberi Pressure Washers

Pump rebuild kit


... Annovi Reverberi Pressure Washers

My Honda GCV160 Pressure washer runs great, but isn't creating any pressure out of the nozzle. Not even a drop out of the wand. Its been on hiatus while I've been recovering from an injury for 3mos. It worked great the 3 years prior. Is there a kit and a schematic to rebuild this pump at a novice level?


Take hose and gun off pump.Start engine.See if pressure comes out of pump.Next, remove water hose and look at filter washer.Clean or replace filter washer.Turn on water and it should come out of pump on other side. ... Honda Pressure Washers

Pump rebuild kit for husky hu80722 - Psi Blue Max 2200 High Pressure Gas Power Washer


I found something on amazon, here: High Impact Design Reduces brake dust I hope this was helpful. Cheers ... Psi Blue Max 2200 High Pressure Gas Power Washer

Replacing impeller How do I remove the pump impeller to put a new one on. There is quite a bit of corrosion and it doesn't want to budge.


Remove the back cover of the motor to expose the plastic fan. Find the c clip that holds it on the motor shaft. Remove the nut that is on the front side of the impeller. I used a vise grips to hold the shaft from spinning on the side where the fan wa ... Hobart AM14-253 Free-standing Dishwasher

My Frigidaire is leaking at the pump and motor connection. It is 10 yrs old and I want to know if it is worth it to repair it or do I need to replace it. The bottom door seal also came off and it has a small leak there as well.


Hi,\012I would replace it...\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101 ... Frigidaire 24 in. FDB435RFR Built-in Dishwasher

Model F180 have just replace the rinse boost pump, but it doesnt want to fill, filled by hand washes etc but eventually runs out of water the fill solenoid is fine


Is the water level float stuck in the up position? it controls a switch which controls the fill solenoid. ... Dishwashers

I have a B&S 3.75, model 98902,type 014301,code 96032254 gas engine which powers a 1500PSI Clean Master power washer. The engine will start if primed but will not continue to run unless fuel is sprayed down the throat of the carburator.Apparently a gumedup/dirty carb. what is the best way to proceed to clean it? Where is best place to get a rebuild kit and/or replacement carb if needed? What are other possibilities if not a dirty carb?


... Pressure Washers

I have a Model G2500VH with a Honda GCV160 5.5 motor. Is there a rebuild kit for the pump?


... Karcher Pressure Washers

I have an Electrolux dishwasher Model # EIDW6305GS1. I am getting an error "01", which means a leak is detected. It did this 5 months ago and the repair man replaced the pump and control panel. Now, after it happened again, I contacted Electrolux. The sent me a Leak Repair Kit, but with no instructions. I contacted Electrolux again and they said that they could not provide the installation guide. Can you help me located the installation guide or offer assistance?


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1007 seconds