Having problems with your Singer Dishwashers ?

The 4Amp fuses blow out during start up after about 10 min.


Answers :

Hi,
\015\012Generally speaking there are basically two styles of drain motor configuration one is attached to the main motor and the other is a separate motor by itself. When the drain motor is a part of the main motor the dishwasher washes in one direction and drain in the opposite direction, if there is some foreign object in the pump it can stop the motor from turning and that can cause the fuse to blow. If the drain pump is separate and defective this can also blow the fuse, but a more common cause of blown fuse that I see frequently is water leaking on to the power wire connection, usually on terminals where the power wire is connected to the dishwasher, these terminals also get loose and will blow the fuse when the connection is poor.
\015\012Also few more details on electric fuses can be checked by going to:
\015\012http://books.google.co.in/books?id=SeMDAAAAMBAJ&pg=PA172&lpg=PA172&dq=4+Amp+fuses+blow+out+during+start+up+DISHWASHER&source=bl&ots=DbmTyskEto&sig=3aYhBPU3LdUn5U540a0xwhjmz3A&hl=en&ei=8NmBS--sOoWyrAe93NCZBw&sa=X&oi=book_result&ct=result&resnum=10&ved=0CCwQ6AEwCQ#v=onepage&q=&f=false
Repair Help & Product Troubleshooting for Singer Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The 4Amp fuses blow out during start up after about 10 min.


Hi,\015\012Generally speaking there are basically two styles of drain motor configuration one is attached to the main motor and the other is a separate motor by itself. When the drain motor is a part of the main motor the dishwasher washe ... Singer Dishwashers

Dear sir, after only 2 years today my dishwasher Whirlpool ADP4737 blow a fuse, after reset it worked again but did not end the program. Started a new program and 5 min before ending it was blinking F3.....


F3 error fault codeThe heating cycle is not working. The error is indicated after several electronic checks are done over a 25 minute period. Therefore if the heater heats too slowly or the heater is open circuit or indeed the electronic control ... Whirlpool Dishwashers

My karcher hds 745 has started blowing fuses. it switches on the power light comes on and it makes a buzzing noise for about five seconds and then blows the mains 13amp fuse. i have replaced it twice but the same happens every time. the power lead is fine


You have an electrical short in the motor windings. you'll have to either replace the motor or buy another washer. also check to see if the motor isn't locked up with a piece of trash. to do that you'll have to dissassemble housing until you get to t ... Karcher 2500 PSI Pressure Washer

My karcher hds 745 has started blowing fuses. it switches on the power light comes on and it makes a buzzing noise for about five seconds and then blows the mains 13amp fuse. i have replaced it twice but the same happens every time. the power lead is fine


Dear dumbelldaveb,\015\012Having a 13A fuse I am concluding that the machine is single phase. Most probably you have a faulty capacitor. Check the capacitor and if you find it expanded and leaking...then you must change it with a new one. If y ... Karcher Pressure Washers

KARCHER 330 attempts to start for a split second then blows fuse in plug. Please help


... Karcher Pressure Washers

Karcher 750mx wont work it keeps blowing the fuse before it starts


... Karcher Pressure Washers

Does anyone know why a Miele diswasher will start to wash fine and then stop with the inlet/drain light flashing after a few mins? I looked at the pressure stat at the bottom of motor and when i blow in it it won't click however i have been told it's very hard to blow into this switch to make it click? any ideas?


Hi, \015\012you may have something rapped around the impellers of the circulation pump causing low water pressure. the unit will start and stop to try to clear the blockage. if the circulation pump is really jammed the inlet/drain light will li ... Miele 24 in. G638 Plus Free-standing Dishwasher

I started working with the Karcher KB4040 pressure washer and all was well for 1-2mins, then it sputered a bit and all power died. All hoses were still attached properly, it hadn't blown a fuse in my house and the fuse in the plug of the washer is working fine.When I switch it on I get nothing. Do you think the motor has packed in? I borrowed the machine from my neighbour who's away on holiday, so don't know much about age of the machine. Any advice much appreciated.


If the water is in anyway impeded, like kink in hose the unit turns off and goes into protection mode. That it it shuts down for a pewriod of time depending on how hot it may have got.\015\012When its rested try it again ensuring you definitely ... Karcher 1750 psi Electric Pressure Washer

I have a k'a'racher 595 it as new been in a box unussed for some time, but when I turn it on it trys to start then it blows the fuse in my plug. can you help me, Kind regards John


... Pressure Washers

I have karcher 397m when i start fuse blows can you please tell me what wronge with machine thanks mr narendra dhokia


... Karcher 1750 psi Electric Pressure Washer

I have a stoves dishwasher i do not know model or serial no only just its a stoves DW 60 it turn on but as soon as the door is closed to start the wash it blow the trip in the fuse box


Its one of two things. Either its your heating element or your motor. Look underneath and also inspect for water having possibly splashed around. Remove both element wires from terminals and place them safely as not to touch anything when testing ... Dishwashers

Hotpoint BFI680 Dishwasher blows 13 amp fuse about 30 seconds after wash starts. Should I bother trying to get it repaired or just get a new one. It is 8 years old. I am assuming heating element is broken. Parts alone are 70 euro plus labour.


... Dishwashers

Dishwasher 66513752K601 keeps blowing the thermal fuse. (Bi-Metal W10258275). I have replace the Thermal fuse several times. After i replace the fuse for some reason after a few months or less it will blow it out again. I have also replace the front panel assembly after it stopped working correctly. I would like to know how to test the dishwasher to find out the root cause of the fuse issue. I don't want to be replacing the fuse every time and don't have the $$ to buy a new dishwasher. Everythin


... Dishwashers

I have a Pressure Washer Keeps Blowing Fuse


... Pressure Washers

The fuse in the plug keeps blowing. Initially it would run for a while - sometimes 3 or 4 cycles - before blowing. It now blows the fuse the second that I plug in to the socket, even with the on/off button on the front of the dishwasher set to off.I'm keen to take it apart, but it's full of water as it blew mid-cycle. Is there a clever way to empty the machine without the power being on, or do I need bits of hose and sponges?A schematic blow up would also be extremely helpful.


Lower the outlet hose into a washing up bowl, it should then Drain. Check the heater to see if it is earthing you get to it by removing the right hand side panel. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a kitchen aid dishwasher model number KUD101TJBLO. I have had the thermal fuse replaced numerous times. It may run two weeks ir it may rub two cycles then the fuse blows. My serviceman has given up on finding a solution.He has replaced the control board and the door switch. However it continues blowing the fuse. I read on the internet that you need to replace the entire wiring kit that comes with the fuse but my repairman says this will not fix the problem and refused to replace the kit.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please check for the short on the wires near the heating element. Also check the resistance of the heating element, it should not be more than 1.6 K ohms. Also ma ... KitchenAid Dishwashers

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

Ignis built in dishwasher keeps blowing fuse


... Dishwashers

I have a hoda pressure washer it stats right up and while i was cleanning the wood fence i let go of trigger during about 10 min, and the motor started dying i pulled the trigger and it pick right up again any ideal what would make that do that? but one time i let it quit and i couldn't get it started,i had to wait about 5 min. then it started back up again.thanks


A couple of things, what makes the engine change tone and revs is pressure, depending on the age, it may have excessive calcium build up in the pump, there may have also been a build up of crud or a wasps nest in the end of the hose when you connecte ... Devilbliss DeVILBISS Devap DVH2600 Gas-Powered Pressure Washer

My GU2500XTPSO would not start. The panel wouldn't light up. My husband ordered and replaced the thermal fuse but the new fuse burned out immediately. Can you help? It will not start or light up. Should I look at another problem causing the thermal fuse to burn out?


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

In line fuse blows 4-5 X/yr. i buy the fuse online at $15 but i am getting sick of changing it. what is causing the fuse to blow? model KUDSO1FLSS3.


First how often is the fuse blowing? does it blow immediatly or over a couple days some dishwashers have a type of tar like substance that is supposed to protect the wires on the inside of the door this is actually one of the worst things they did wh ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Karcher HD6/13 4M blowing fuses on startup


... Karcher Pressure Washers

Karcher HD6/13 4M blowing fuses on startup


... Pressure Washers

Our Frigidaire dishwasher, Model # FDB2410LDS0 has power and will start on any cycle, but after filling with water, there is a pause and then the lights just start blinking and it stops at around the 92 mins remaining display. We have tried shutting the breaker off for 10 mins, then back on, hoping to reset it with no luck. Any thoughts?


... Dishwashers

Hello I just borrowed a k archer k 2.87 water blaster from a friend and forgot to turn water on before starting motor. Motor stopped after a few seconds and now won't start. Online guide says to change fuse but nz version doesnt have fuse in plug. Do i have to take machine apart?HELP Please!


Most of the time it is the GFCI on the end of the plug that goes bad. If it were me I would cut off the GFCI and wire in a standard 120v plug. If it still doesn't work after that then there is a good chance that something electric internally has gone ... Karcher PSI Electric Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1019 seconds