Having problems with your Smeg 24 in. DWD1SSE-1 Built-in Dishwasher ?

Dishwasher is model DWD1SSE type11045 Initially the dishwasher leaked water on the floor On investigation the bottom tray under the dishwasher was wet The motor was wet Tested the motor which was fine although the capacitor on the motor impellor was dead. Replaced capacitor, now no water going around the spray heads so found the impellor inside broken. Replaced that. No hoses are leaking. Machine now works fine heats up etc etc but over fills and the E5 fault shows


Answers :

Repair Help & Product Troubleshooting for Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher is model DWD1SSE type11045 Initially the dishwasher leaked water on the floor On investigation the bottom tray under the dishwasher was wet The motor was wet Tested the motor which was fine although the capacitor on the motor impellor was dead. Replaced capacitor, now no water going around the spray heads so found the impellor inside broken. Replaced that. No hoses are leaking. Machine now works fine heats up etc etc but over fills and the E5 fault shows


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

The ge profile dishwasher model PDW8280J10SS was purchased about 2 yrs ago. It was working fine up until Jan. 2009. It ran fine but the water stopped draining. I read were you should run the garbage disposal prior to running the dishwasher. I drained the water and did this. It worked fine for a while then the problem was back. Once again, Drained all the water, sucked it out with a turkey baister, moved the dishwasher and checked hoses etc. Once again, it worked fine for about 10-14 runs. It now


It is probably clogged at the pump or before. See if you can get outlet hose off the bottom before the pump. ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Frigidaire dishwasher Water does not go through arms, bottom or top, at all (does not wash). You can hear motor running. Pump works fine; discharges water as normal and fills to proper level. Problem just started with no warning; no strange noises etc.


CHECK WATER INLET SOLENOID OR TIMER ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have GE GSD2300r00bb, it was working just fine the other day no unusual noise, today we tried to run it, just a little bit into the cycle, i heard a strange stalling noise that sound like the motor is stuck or something, i put a camera(in a ziplock bag) in the dishwasher to see if the blade is spinning, no spin, the water did squirt for about 1 sec then stop but still leaking out somewater. Is it the motor or the water pump. I just got this dishwasher about 1.5 yrs. Is this something i can fix


... GE GSD2300RBB Builtin Dishwasher

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

Problem for Kenmore 24 in. 15992 Built-in Dishwasher Previously answered by Ginko but have not had any responses since June 18 and problem not solved. No water flow into dishwasher. Actual model is Kenmore Elite undercounter dishwasher 665.15982990. Float is not stuck. Worked fine for 10 years until mid May. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound when starting cycles, only a single electronic click. When cycle is canceled, motor does s


Hi.Sorry about your old query.If there is no power on black wire and no filling, then check and eventually replace the thermal fuse. The thermal fuse is attached to control board. If it is faulty it will read continuity, norma ... Kenmore 24 in. 15992 Built-in Dishwasher

The top dishwasher is flashing F1 and the motor won't turn off. It will drain if I pour a cup of water in it. The bottom dishwasher is working just fine. There is no water in the bottom pan. I usually find a few drops of water when it's flashing F1. Thank you!


Hi.the troubleshooting, and the error code depends on the make of the dishwasher.If the dishwasher does not stop draining, then the float sensor switch, or the pressure switch in the drain system is faulty.Details ... Dishwashers

Water is not going into my dishwasher --worked for 13 months fine and now having a problem. When I turn it on the motor runs and rattles - louder than before, but no water is going into the dishwasher. We did nothing different and have not changed anything.


Try running a diagnostic run on the washer. Push heated dry, normal, heated dry, normal on your cycle selection panel. After you push that sequence all the lights will light up and then it will go through a test run. This fixed my washer that had the ... Whirlpool DU1055XTS Built-in Dishwasher

Hi, I have a 10yr old Neff s5543 built-in dishwasher, it is has been working fine but recently has stopped fully draining. I have removed it from the housing and checked all pipe work is unblocked and not kinked, have also blown back down drain tube to free any blockages from drain pipe, have also removed pump cover and checked around impellor for any foreign bodies etc. Everything seems clean and free. I ran a complete heavy cycle (empty dishwasher) and allowed drain pipe to drain into a


Hello there and thank you for choosing fixyaOk there are acouple of things that can be checked on this along with what you have already checkedDrain solenoid\015\012 \015\012 \015\012 \015\ ... Neff 24 in. S5543X2 Built-in Dishwasher

Kenmore model 16309. The dishwasher has power and water but the motor does not seem to be working. It hums for a second, but quits. The timer is working and the water seems to be coming in fine. but the arms are not turning. Any thoughts?


Hi\015\012\015\012 \015\012\015\012The timer is working, unit has power and it also fills\015\012water, all this indicate that it is the motor that is bad and should be replaced\015\012to solve this issue. Moreover, the hum sound ... Kenmore 24 in. 16309 Built-in Dishwasher

Dishwasher drain is hooked to a food disposer and until recently the unit worked fine. Last week following a cycle a couple of inches of water did not drain out. All food is removed from dishes, silverware, etc. prior to loading and the food trap in the bottom is completely clear. I ran the unit empty through a Lightwash cycle and afterwards the water level (that which didn't drain out) looked to be the same as before. The dishwasher is run 2-3 times weekly whereas the food disposal is


Hi, The I don't think the problem is with the loop and the 32" above the floor.If the dish washer was removed from one house to another, did *********** ever have a dish washer in the house before that he replaced this one with? The reason I am aski ... Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

Wash motor My dishwasher was working fine but the timer went out. It has sat there for about 1 year and I have now replaced it. It now cycles through but no water ever comes out to wash. I had an different dishwasher that we use to have at a lake house that would sit there over the winter and all I had to do was reach underneath and spin the little finned wheel and it would work....is there something like this on a DRU141 model? I just have a hard time believing that it is that when everything w


When a dishwasher doesn't get used, the gunk under the float switch dries up. Get that thing moving again, and you'll be back in business! ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Water from my disposal backs up into my hotpoint ($300-model) dishwasher. The dishwasher works fine otherwise. Is there a one way valve in the diswasher that is suppose to prevent reverse flow and/or is there other dishwasher motor problems which could cause this. Actually the Hotpoint Model number is HDA3600N00BB but this website did not recognize that model number so I put in the closest model number closest to mine.


If it's what I think, it's a simple fix. Does your dishwasher drain run along the floor of the cabinet, then up to the disposal? (my guess is yes). There should be an "air gap" between the disposal and dishwasher, this means when it comes out of th ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

I have the Kitchen aid KUDS01DL dishwasher. It was working fine until last week. When starting a cycle, the washer fills with water. Once filled, the motor makes a humming noise and does not circulate the water. I end up stopping the cycle and the discharge pump empties the water. I took apart and cleaned the basin this morning. I did find some random garbage but it did not seem blocked. Do you have any ideas?


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

My dishwasher only fills half way and it dosn't go through the wash cycle. It pumps the water out and then go to the rinse cycle but has the same problems with the water level. We have checked the motor, pump and the water valve. It seems to be working fine. Thought it might be the timer.


Hi,\015\012\015\012This is an issue with the wash motor..\015\012There are two motors,a wash motor and a drain pump/motor assy\015\012The wah motoe must have been the issue with the case.Changing the wash motor will solve your ... Dishwashers

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

Dishwasher not working. Noticed dirty water in bottom. Cleaned filters etc. now can hear motor but no arm movement etc. any ideas?


Check for a pice of broken Glass in the mechanisem ... Dishwashers

Dishwasher was cutting out intermittently,totally dead no power then after 15mins or so,finally went bang this am,smoke etc,took insection cover off at bottom swit6ched on again to see spark dead short on unknown unit with four wire block connector attatched,two white to same connector and two purple,left disconnected and workin fine,hot water,inlet and outlet both working fine so what does that unit do?


... Bosch 18 in. SRS43E02 Slim-Line Built-in Dishwasher

My dishwasher is not pumping water in or out. The heating element etc are working fine on the dishwasher though.


It sounds as if the pump is the problem, it may be blocked or more likely seized or the motor is dud. ... Jenn-Air Dishwashers

No water flow into dishwasher. Float is not stuck. Worked fine for 10 years until yesterday. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound, only a single electronic click at start of cycle. Actual model is Kenmore Elite undercounter dishwasher 665.15982990


Hi.Try tripping the circuit breaker or disconnecting power cord for a couple of minutes. While power is off, check the inlet cable at the back of the machine.If\015\012there is no water getting into the machine, and there is n ... Kenmore 24 in. 15992 Built-in Dishwasher

I have a bosch smu 2000 series dishwasher. it has always worked well with no problems but then all of a sudden a week or so ago, the water stopped coming into the dishwasher to wash the dishes. the faucet and all other water areas continue to work w/o problems (i.e. bathroom, shower etc). in attempting to use the dishwasher, the entire cycle seems to be working, i initially hear what sounds like an initial water discharge when the cycle first starts and during the entire cycle it sounds like it


... Bosch Dishwashers

I have a whirlpool dishwasher DU915WKSO: when I turn the dishwasher on, the heating element comes on but no water comes into the unit. I recently replaced the garbage disposal and th dishwasher worked fine for a time or two. Since then I have only been able to get water in it once. Like I said, the heating element works but no water in the dishwasher. Thanks for any help.


... Whirlpool DU1055XTS Built-in Dishwasher

I have a slimline dishwasher from Ikea. The model is Whirlpool DWH C10 W manual. Everything worked fine up until the other day when I switched the machine on and it made a noise as if it was working but nothing happens. No water comes into the washer although inlet pip looks fine. I have poured water in and it is drained okay but the dishwasher is not cleaning dishes. After checking through numerous forum and reading about a flood prevention switch which can be sorted by tipping the d


Ok so slow down and lets look at the d/w problem and don't take the kitchen apart.. in the tank there is a float in the front corner. lift the float and listen for the click that would be the float sw . if no click th ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2802 seconds