Having problems with your Smeg 24 in. DWD1SSE-1 Built-in Dishwasher ?

E1 fault code displayed

\015 Sparking from inside dishwasher noticed when emptying dishwasher. When attempting to use dishwasher after this, fault code E1 appeared after approx 5 minutes. Any help on this would be appreciated.\015

Answers :

Repair Help & Product Troubleshooting for Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hello, dishwasher whirlpool ACP 4738 display fault code fb (f6 ?) after 3 minutes run. Do you know what fault code means ? Thank's DT


... Whirlpool Dishwashers

Whirlpool ADP5966 - flash code 12 and fault on display F6


Chech drain pump ... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

I have a John Lewis dishwasher (JLBIDW901). Today it would not begin wash cycle and displayed the fault code i30. The manual states that this means the Anti-flood device is activated. I know the sup


... Dishwashers

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Prima dishwasher displaying fault code e4


... Dishwashers

E1 fault code displayed


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

Dishlex global 460 fault.. Always stays on and makes a pumping sound while 'of' is displayed. Only way to turn it off is at the power point. Have tried turning it off at the power point for some time and re setting by pushing start & program at same time with no luck. According to the manual the code says "incorrect fill levet or time " and contact service for help. Any ideas?


... Dishwashers

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle


... Bosch 607335 Water Valve Assembly For Dishwasher

My zanussi zdf 601 dishwasher displays fault code 60 after the wash cycle has started, can you help me please


... Zanussi Dishwashers

A05 code dishwasher flooded kitchen during wash cycle i have emptied all out cleaned filters stripped and cleaned pump and made sure of no blockages put machine back on it workes for a short while then displays fault a05


... Indesit 24 in. DE73 Evolution Free-standing Dishwasher

I have a Baumatic Dishwasher BFD63ss and it won't complete a cycle. About 5 mins into the wash it bleeps and the display shows fault code 002. It dones't appear to be getting hot either.


... Baumatic Dishwashers

The Wash/Rinse, Drying and End indicator lights flash simultaneously. Fault code 14 shows in the Tome left display


... Dishwashers

Hi there, my F&P nautilius dishwasher starts the cycle as soon as I push the power button but only pumps out then swithces off. It won't let me set or change the cycle. I turned it off and left it over night and in the morning it had overflowed with water. There is no fault code showing on the display either.


When you said overflowed with water did the water come out the door the float switch in the unit may be stuck either opened or closed which if it were stuck or the switch itself were broken then the unit would have water go in and immediatley go out ... Fisher and Paykel Dishwashers

Dacor Dishwasher Mod# MDW24S Not starting at all , digital display fault code= PF---CL Tennant says it randomly starts and makes a noise. Any ideas?


OK Well PF means Power Fail, either it has been disconnected from the mains at some stage or the Power has gone OFF.\012\012\012CL (CLOSE) is basically its telling you to close the door. If ... Dishwashers

Hi I have a Miele G1270 SCVI Dishwasher and it keeps stopping only a few minutes into the cycle and displaying the fault code F14 do what does this mean?


... Miele Dishwashers

I have a Siemens SN25M230GB Dishwasher showing the following: Fault Code E15 Digital display showing (Error) E15 with a flashing 'tap' What does this mean? Is it something that I can fix myself or does it need to be looked at by a professional? Thanks Tina


... Siemens Dishwashers

Dishwasher stops and displays fault code F7 - Whirlpool Dishwashers


If you have checked the sump filter at the bottom of the dishwasher,\015\012then close the door and turn on the power. then hold the start button\015\012with the + and - buttons under the LCD display, untill the drain pump\015\012starts. this should ... Whirlpool Dishwashers

I have a miele g2220 sci dishwasher. keeps stopping during cycle and displays fault code F14 which is not in the manual. please help.


The clogged circulation pump (error code F14) ... Miele Dishwashers

I have a Kitchenaid dishwasher #KUDK01LBS6.The unit will not run. The ''Clean Light'' indicator on the display panel blinks off and on. I have read that a ''Fault Code'' is needed to solve this problem, can you provide me with one? Thanks! e-mail [email protected]


... KitchenAid Dishwashers

Dishwasher will not cycle. displays code 10


Hello there i have read you review ok there is a fault coming from the water pump there is no way to fix this manully you will need to take it in for a repair witch can cost up to $50 for a new water pump ... Dishwashers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

Fisher & paykel dishdrawer ds605 f7 fault code. Lid failure. This is the second code (after F9- power controller fault).The lid of the dishdrawer will not raise and release the drawer. The lid is stuck in the down position. Assuming this is a power/electronic controller fault. Part numbers would be good.


You can force open the drawer without causing any damage. The actuators on each side will let you do that. But you push it back in unless you manually move the actuators for which you will have to take the drawer out of its housing.\015\012 ... Fisher and Paykel DS605ZW Dishwasher

U2 Fault cde displayed at start of wash cycle


Hi,The reason for U2 fault code in your dishwasher is due to the problem caused beacuse of loading. Check loading to ensure no items extend beyond the height of the drawer. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bosch SHE53M Dishwasher Fault Code c3


Change control board ... Bosch Dishwashers

I keep getting a beep and believe it is a Fault Code


Try turnning the unit of at the plug the the controll panel holde the program botton in and trun unit on try this on both draws ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0399 seconds