Having problems with your Smeg DFC612S Built-in Dishwasher ?

We have a 5 year old DFC612S built in dishwasher, the programme button has gone inside the front panel, any tips on how to remove/repair? Thanks


Answers :

Repair Help & Product Troubleshooting for Smeg DFC612S Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a 5 year old DFC612S built in dishwasher, the programme button has gone inside the front panel, any tips on how to remove/repair? Thanks


... Smeg DFC612S Built-in Dishwasher

Smeg diswasher model numbe4r DF612SDX. Just coming up for two years old, various codes re error messages. E2, E5, E8. We have taken off the front panel where the buttons are - nothing obvious. We have taken the bottom off and tried to locate a reset button, but can't find one. We have cleared all the filters inside and checked the water intake and the filter there. Out of ideas, can anybody else suggest what we can try?


Any signs or sounds on the machine you here when the problem occur? ... Dishwashers

We have a Quiet series 200 Maytag Legacy Series about 2 years old. Some of the buttons on the push pad button panel won't work including the start button. Some will work and some some the lights are green so I know there is power. It seems maybe some of the buttons are broken down so as not to engage. Can the front button panel be replaced assuming that is the problem? Thanks, [email protected]


Hi\015\012\015\012You are right.... if there is power to the unit so the power\015\012board seems to be working fine and the control panel should be replaced. Hope\015\012this helps...please post back for further assistance.\015\012 ... Maytag Dishwashers

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

Mod# mdb7601aww.... When I press cycle key, say heavy duty, then close door the 2H light flashes. I press the start button and the unit will not start. I have shut it down electricly and get the same results. what can be the problem? The front panel with the start/delay buttons or the inside control panel? I like to figure this on out the first time because each of those parts are $100+.


... Maytag Dishwashers

Thermal fuse Dishwasher konked out mid-cycle and now no power to control pad. We've already had the thermal fuse replaced once (machine is only 2 years old!) and this appears to be the same issue. I tried to open the front and I think I can see where it is but not sure how to get it out and replace it AGAIN. I wasn't able to get the inside panel completely apart from the front of the unit so I was somewhat limited. I'd rather save the service charge if I can and there's n


Http://www.partselect.com/MultiModels.aspx?ModelNum=KUDS35FXSS&SearchTerm=fuse&RefineSearch=0Maybe this link will help ... KitchenAid KUDS35FXSS Dishwasher

I have a GE Quiet Power 3 that has completly died. I cannot get a light to come on or anything to beep when pressing buttons. I checked the circuit breaker and outlet and they are both working fine. I tried pressing and holding the reset button on the front control panel and nothing. It seems to have just died at 2 years old. Anyone have a solution? GE wants $80 just to look at it.


A dead set simply means a cut off of power supply. Open the back cover of your dishwasher . Locate the area where the AC cord is located and look for the plastic fuse holder which is usually installed in one of the AC cord line open it and replace t ... Dishwashers

I have a Jenn Air JDB 4000 AWB that is seven years old. I have had several problems with this unit during that time. Yesterday when I tried to open the door the "push handle" stuck in the depressed position inside the front door panel and will not release. The front door is locked shut. I have not tried to force anything (yet). How can I get the door open?


... Jenn-Air Dishwashers

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

I have a Hoover Nextra HND 315 si dishwasher. The power light on the front comes on, but none of the programme buttons light up or work?? Have tried taking the panel off the front but all seems to be moulded in one peice and am unable to access the inside electrics...any ideas??


... Dishwashers

Have a 4 year old Kenmore Dishwasher Model # 74382. No problems at all until last week I went to start it and it would not turn on. Lights on the control panel were on with exception to the start light. I opened and shut the door to make sure it clicked and pressed the start button again and nothing. I tapped around the panel with the side of my fist and pressed it again and it began working. Well today different story I went to start it and it did the same thing. I tapped all over front of the


The problem is more likely the door switch is failing or out of adjustment/loose. You will need to remove the door panel. This is easy to do. There is a video at ... Kenmore 24 in. 74382 / 74384 / 74389 Built-in Dishwasher

I have a Neff built-in dishwasher and sometimes there is a heavy leakage of water from the front right-hand side. The unit is 3-years old and there is a build up of scale around the rubber seals. The long seal at the bottom of the door seems to have receded slightly behind the metal panel on the inside of the front door. Is the seal easy to replace ?


Hello,\015\012Check the rubber seal in the bottom of the door has not perished or split,also check the bottom spray arm has not split on the ends as this will direct the spray directly onto the door,causing it to leak.\015\012\015\0 ... Neff 24 in. S5443X2 Built-in Dishwasher

Hello I'm looking for advise on my 11 year old dishwasher. It's a kenmore ultra wash model # 15812. The problem is that when you push the wash button nothing happens. The drain funtion still works and all the lights on the front panel work but no water is flowimg into the washer. Do I try to fix this or just buy a new one?


Hello there:To be honest with you i would first try these solutions and see if they work cause a new machine would cost a lot of money.But if you can fix yours it would cost a lot less so plese try these solutions that i have provid ... Dishwashers

I have a Kenmore UltraWash QuietGuard Model # 16632. Yesterday after 8+ years of problem free operations, it stopped working. When I went to unload it, the dishes were completely dry, the inside of the unit was still warm but there was about 1.5" of water in the bottom of the machine. None of the front panel light or buttons work any longer and I have verified that there is power to the unit. Help?


... Kenmore 16632 Built-in Dishwasher

Have bosch SHE45 EVOLUTION PUSH BUTTON ON RIGHT FRONT PANEL. MY WASHER WILL NOT RINSE ALL THE SUDS OFF THE DISHES OR DOWN THE DRAIN AND HAD BAD SOAP RESIDUE BUILD UP. i HAVE USED LEMISHINE ONE TIME AND THE HARD WATER REDISUE IS GONE. BUT SUDS IS STILL IN BASE OF WASHER. HELP.


I started running the Hot water faucet till I got really Hot water then I started the dishwasher with No dishes in it and let it fill with hot water till it was almost full then I added a half a gallon of white vineagar to the water and let the dishw ... Dishwashers

I have a 9 year-old Maytag dishwasher. The front button panel has become so indented, I have trouble getting the machine to turn on. What to do?


Remove 2 screws on bottom take panel off fix indent...thumbs upVE6GAR 73 88 99 ... Dishwashers

My dishwasher (Maytag MDBH965AWQ quiet series 300 was purchased in May 2006 (making it just a little over 4 years old). The handle broke on it initially and now the control panel has gone out including the start button. The cost of the replacement parts is right around $200, so I don't think it is worth investing that kind of money into it since it seems to be a lemon anyway. I have always been faithful to Maytag. At the time of our kitchen remodel in 2006, we chose all Maytag appliances. I


Well Kathy, you may be in luck. There has been a safety recall on your model of dishwasher and Maytag will give you a considerable allowance to replace with another Maytag. You may contact them at 1-800-544-5513 with your model and serial number and ... Maytag Dishwashers

Problem: dishwasher (moel MDB6601AWW) will not run. The front panel has a light, between the "Delay 1-9" and "heated dry" buttons, and adjacent to small printed icon (looks like a tombstone with the number 3 inside). Last weekedn I shut off all the water in order to change a faucet, including the hot water feed to the washer. Now the fed to the washer is somewhat frozen -- I can only open it 1/8 turn. So, I wonder if my wife tried to run the machin with no water flow, and it shut itself dow


... Maytag 24 in. MDBH955AW Built-in Dishwasher

I have a Maytag quiet series 300, model # MDBTT60AWW. The front control panel have some green lights on but the start/cancel button won't work. The dishwasher will work for 5 days and quit for 2-3 days then work again. I tried to reset the main electrical panel hoping the dishwasher will reset too but it didn't work. I opened the panel on the front door to see if water is getting into the electronic panel but it is dry. I'm wondering if it is the front control panel itself is the problem. I want


... Maytag Dishwashers

Two LEDs continuously blinking on front panel. Will not reset when "cancel" button is pushed. Will not respond to any buttons pushed on front panel. What to do? Thank you.


Sound like you have a bad touch panel. replace your touch panel and this should solve your problem ... Kenmore 24 in. 15932 Built-in Dishwasher

Dishwasher GSD2030F03WWSA735136B Model Series number;Piece fell off inside front panel, making it impossible to turn on dishwasher at all..so I took off front panel screws, opened dishwasher and saw white plastic piece but can't find where it goes but it must have something to do with turning the knob to start dishwasher because the knob won't turn now..so it must attach inside somehow but I can't figure out where it goes...help!!


I think you need to get a new knob, write down the model number and make and take the pieces to your local domestic appliance supplier, there might be something similar in stock. Now I do mean the kind of small supplier that understands this kind of ... Dishwashers

When pressing any front button on the control panel nothing will light up or start up in any manner,does look like it did not finish draining,have water sitting in the bottom. Pulled off front access panels no signof burned wires or anything becoming disconnected? do have small childern in the house pressing buttons? power is good going to unit.??


1)check any fuse blown in board.\015\0122)check supply to the board. ... Kenmore Dishwashers

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

I bought a used 001355 asko dw. the front door panel and all under panels are naturally loose and I'm having trouble figuring out the reassembly order. And then as I was trying to install the main galvanized under panel, a short galvanized sheet metal part fell out of the door inside the unit. That's the part that now has me really stumped. Can I get a picture of the front of the unit, preferrably an exploded view? Thank you. Paul Cowden. (415) 777-9858 or (415) 302-0628.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1252 seconds