Having problems with your Smeg Dishwashers ?

I have a smeg st663 that has the delicate and normal wash buttons illuminated and the intensive button flashing after the last wash. Some water failed to drain and I can,t reset it. Any suggestions.


Answers :

Hi.

Try first to reset the error follow the procedures below.

1:
\015\012
    \015\012
  • Hold down program selection button for up to ten seconds
  • \015\012
  • Close the door.
  • \015\012
  • After approximately 1 minute the dishwasher will advance to the end
    of cycle.

2
\015\012
    \015\012
  • Turn off power from main circuit breaker.
  • \015\012
  • Dry water inside the dishwasher.
  • \015\012
  • Clean the filter unit (see Manual here, page 26 )
  • \015\012
  • Apply power back.

3) If that does not work, please try the following procedure, it should enter diagnostic mode and reset the error.

\015\012
    \015\012
  • Switch off the appliance
  • \015\012
  • Turn the dishwasher back on.
  • \015\012
  • Before any of the lights coming on press immediately the program button. Program button must be pressed 4 times within 4 seconds.
  • \015\012
  • The two last program lights (normal and intensive) should start flashing.
  • \015\012
  • Press again the program button once.
  • \015\012
  • The Normal light will turn off.
  • \015\012
  • The last light will keep flashing.
  • \015\012
  • Switch off the appliance.
  • \015\012
  • Wait 10 seconds.
  • \015\012
  • Switch the appliance back-on.
If error is still there, then the problem is water pump malfunction. This will turn on second and third light from the left (light wash and regular wash)

The appliance cannot pump out the water. Check that the drain hose is not kinked or crushed and that the siphon and filter are not fouled. Check height of the drain hose at the back. Clean the drain well and filter located on the bottom panel of the machine. If the problem persists, contact the after- sales service. The pump must be accessed, freeing the hose connected to the pump from blockage, and testing the pump motor.

Note if lights are instead first (soak) and third (regular), then the problem is water inlet. In that case check pressure from the house, inlet hose. If that does not fix the problem, then the inlet valve and water level switch must be tested.

If lights are Delicate and Normal (the one with glasses and the one with dishes), then the problem is drain.

Regards.

Ginko
Repair Help & Product Troubleshooting for Smeg Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a smeg st663 that has the delicate and normal wash buttons illuminated and the intensive button flashing after the last wash. Some water failed to drain and I can,t reset it. Any suggestions.


Hi.Try first to reset the error follow the procedures below.1:\015\012\015\012Hold down program selection button for up to ten seconds\015\012Close the door.\0 ... Smeg Dishwashers

Hi, I have a Siemens SE44 dishwasher with Aquastop, which I bought recently. It was doing great for first 3-4 wash cycles and then it stopped functioning :( Now all it does is let the water in, and then drains it out- it doesnt do anything else. I can hear the water going in and then the machine drains the water,and this repeats. I tired resetting the dishwasher, checked the drain pipe, aquastop etc, and all seem to be in order to me. Any suggestions? Many thanks, stonerockyy


... Dishwashers

I have a kenmore ultra wash mod# 665.13492k600 dishwasher that in the last couple of days will not drain the last cycle . If you push the cancel /Drain button after the cycle is finished it will then drain but all the dishes have soap spots on them and are very wet .I have checked for clogs but cant find any I have also run a lot of water throug our waste disposla because the dishwasher drains into it help ??


... Kenmore Dishwashers

I turned on my Whirlpool dishwasher last night before I went to bed. It is a model number DU915PwP82. Sometime shortly after that, a water line broke in my neighborhood. The water was off and caused some sort of problem with my dishwasher. There is some water in the bottom of the dishwasher. It won't drain or start washing. Do I need to call a repair man or is there a reset button of some sort. Thanks for your help. Rina


Hi.\015\012Often there is a lot of grit in the water supply after a pipe has been repaired, and this may have clogged one or more of the valves in your line, or the gauze filter in the inlet port on your machine. I would first turn off the wate ... Whirlpool Dishwashers

Whirlpool dishwasher ADP 4502 Water fills and stops repeatedly then its drains immediately without washing and then stops Cant use the dishwasher @ all. resetting it doesn't help I am 7 months pregnant, insulin dependent and really my dishwasher


Hello, ryklien\012 \012 I was trying to help\012 you out here. I was going back to some customers that asked questions \012in the past and it appeared that no one answered them, so I thought I \012would take som ... Whirlpool 24 in. ADP5962 Free-standing Dishwasher

I have a Siemens dishwasher serie IQ which has had water damage. There has been water pressure on the drain tube. Probably the mashine has been partly filled with drain water. Now it can start and pump out the water, but it never starts any washing program. Well it starts and the time left (e.g. 15 min on the shortest program) is displayed. But then it does not start to wash or count down. Any idea what is wrong or broken? Anyway I can repair or reset the dishwasher?


... Siemens 24 in. SL84A305UC Built-in Dishwasher

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Upon selecting a wash cycle and closing the door the machine starts normally (heating water stage) but never clicks to allow water in and wash the dishes. Fails to advance to the wash cycle and just runs without doing dishes. There was water in the bottom after the last wash, filters are clean?


... Bosch SHV46C03 Built-in Dishwasher

I have a Bosch "Classic Electronic" dishwasher that has been in use for only 18 months. If it helps - SGU53E05AU/30 is marked on top of the door.. my problem is that on the last cycle, the water won't drain so I am left with lovely clean dishes but there is water up to the drawer line present and it won't drain until the next wash. I have cleaned all the filters and ensured the pipes are not obstructed. It is odd that it only does it on the last cycle. Could it be the microchip?


Hi there,\015\012\015\012thank you for providing the model #, that helped me narrow down the troubleshooting.\015\012\015\012try the following to fix your problem:\015\012\015\012check for blockage or kink in the d ... Bosch Dishwashers

My Kenmore Elite dishwasher did not drain the water out of the bottom after the dishes were washed last night. Could I possibly have pushed a wrong button to keep it from draining, or do I have a problem? All the dishes were clean. Should I run it through another wash cycle? I've got water standing in the bottom of my dishwasher.


Yes , If the program controller has hung it would have skipped the drain cycle. So try to redo the cycle and see if the drain works, is not check the program controller and the drain valve/pump.- if there is food particles that have clogged and block ... Kenmore Dishwashers

We have a +11 year old Bosch SHU3006/UC/U06 that never leaves the wash cycle. We had to stop it during our last test run at 3 hours. Chat advise is suggesting a water temperature problem (I origionall thought the timer), suggesting that the cycle will not advance until it hits a set temperature (170 degrees). We checked and noticed that the water in the machine was only around 90 degrees during a wash cycle. We do not have exploded views or parts drawings, nor electrical schematics. I wou


Check continuity of the heating element to see if it is broken/open.\015\012\015\012The dishwasher prefers that the incoming water (water heater) be 120 degrees (F) ... Bosch SHU3036UC Dishwasher

Our dishwasher seems to be stuck in drain mode. My daughter put the wrong kind of soap in it. She accidently put Regular dish washing soap in rather than machine dish washing soap. We've got all the suds out. Seems to drain water just fine. However we cant seem to get it to add water. Does the soap have anything to do with it? Anything I can do from my end? Please Advise. Thanks


Plastic base is full of water. Need to remove whole unit to access bottom and dry it out. ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

Hum in Kitchen Aid Dishwasher Model 8531529. Stated last night. No hum when filling or draining - only during the wash cycle. Can still hear the water spinning inside during the wash cycle, but hum is loud. The water does fill & drain completely/correctly. Any ideas? Might this be an easy fix? or a likely repair man call? Thanks!!


Hi\015\012\015\012The hum sound that you hear is from the motor that is not\015\012working or is about to go out, the motor should be replaced. Hope this\015\012helps...please post back for further assistance.\015\012\015\012Dani ... KitchenAid Dishwashers

GE GSD4920Z dishwasher. Problem is that it does not drain completely at the end of the cycle--about an inch of water remains. After checking for clogs, etc, we followed a troubleshooting procedure which involves a hard reset (power off, then reset twice at beginning of cycle) and this procedure successfully drains the tub. However the next time that it's used on a normal cycle, water remains again. Suggestions?


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa.\015\012Dishwasher not draining properly or not draining at all issues can arise due\015\012to different reasons. Usually, these issues are related to kinked hoses,\015\012knocked o ... GE 24 in. GSD4920Z Built-in Dishwasher

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

My bosh dishwasher SHX55M06UC/46 will not drain. A new disposal was put in and the dishwasher drain plug was not punched out and the dishwasher was ran that way. Now it just holds water in the bottom. I've tried resetting or canceling the wash cycle but that doesn't work and the washing cycle works fine. I'm hoping there is a reset or a safety for the pump if it gets clogged.


... Dishwashers

My Kenmore ultra wash 6651736 dishwasher broke almost to the month it turned 6 years old and I'm trying to decide if I should fix it or buy new.It washed wonderfully up to the day it stopped .the water fills ,but no water sprays around.the water fills to the correct level and I can feel the water heat. I can push cancel and it will drain. Right before it broke there was a terrible grinding noise for a few loads.No water leaks.the newer models don't seam to last long.this one is replacing one t


Hello,very common issue on these units, the motor had failed, the motor did have a five yer warranty but we are beyond that.You can purchase the part from the link below, ... Kenmore Dishwashers

Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a haier dishwasher model WQP12 AFM, I've replaced the wash pump motor and drain pump (they had been damaged with water after last repair person didn't put widget around drain hose which split and water accumulated on bottom). It well for about two weeks, then it would not go through it's cycle and I noted water not heating up. Have checked element with meter, thats fine, I replaced timersince it wasn't going through its cycle and that has not changed anything. Any suggustions?? Cheers


... Haier Dishwashers

Frigidaire Dishwasher model # FDB520RHB2 Stopped prematurely last night while on light cycle, now will not respond at all. Noticed water at bottom of tub; tried draining manually through drain tube, removed lower arm, glass trap, and filter, and water remains; tried electronic reset by switching off breaker for several minutes; all to no avail. Electronic controls (cycle/option select) will not respond at all.


This is not a uncommon problem and it sometime's is the pc control panel but i find that it is more often the interlock ( latch assembly .) i would change // there has been a improvment and i belive this will solv ... Dishwashers

In between wash cycles, water seems to back up into the dishwasher. I had a plumber take a look at the drain and disposal in the kitchen sink to see if there was an issue there. He suggested to have appliance repair tech to come look and indicated that he believed that the issue may be the "cylianoid" valve. Does the this valve prevent water from backing up into the dishwasher after it has drained?


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

This is a past problem posted that I am now experiencing with my Kenmore Elite Model 655.17489300 dishwasher. Looking for any suggested solutions, Rick Past Problem: I have the same problem with my 2004 Ultra Wash Model 665...fills with water, sensing light comes, then stops for a second. Then you can hear another pump kick in (it hums) and just runs continuously but no water is spraying through the arms. When you cancel the wash, it drains perfectly. I've checked the filters, all is c


The symptoms you have mentioned could be linked to the soil sensor which some models come with. The purpose is to run the drain pump and let more water flow through inlet valve if during wash cycle the dishwasher detects soil collection in the accumu ... Kenmore 24 in. 16539 Built-in Dishwasher

Jackson jp-24b purchased this machine used, cant figure out how to work it. I flip the auto cycle on, and then the power switch. The fill light turns green and i assume water is filling up in the machine. In the meantime there are two small red external hoses that hot water comes and i currently just have those hanging in the sink. At the same time, nothing is happening during the wash cycle, the wash gauge doesnt even move only the rinse gauge. Also when i try to drain it nothing happends (begi


It needs a new drain relay box 120 volt the drain is stuck open the jp 24 were not very good machines the red lines are drain lines if you plug up the drian lines at fillup the machine will wash but now it will never drain a new drain box is not c ... Jackson JP-24B Built-in Dishwasher

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1941 seconds