Having problems with your Smeg DWI614 Built-in Dishwasher ?

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


Answers :

I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.
\015\012
\015\012I traced the fault to a broken wire between the electronic module in the door and the pump. The point at which the door opens and closes on the cables had frayed the insulation and broken through the wire. As this was the live feed to the pump and a potential short from 240VAC to the chassis its dangerous!!
\015\012
\015\012Repairing the wire break and re-insulating fixed the problem.
\015\012
\015\012Lee
Repair Help & Product Troubleshooting for Smeg DWI614 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

My deceased parents have a GE dishwasher (don't know the model number - can't find it on the machine and can't find the paper work) that stops working shortly you start it and displays a message on the front panel that says "Blocked wash arm - check for wash arm obstruction - restart". We restart it and get the same message shorty thereafter. This happens when the washer is COMPLETELY EMPTY, even when we remove the bottom rack. It first started after several month of inactivity. We'll just t


Could be false sensor input, could be that the arm is not turning, I am not sure how old your machine is, but age could play a part if the arm is "in fact", not turning. If you are not mechanically inclined, I would suggest that a qualified repairma ... Dishwashers

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


... Dishwashers

I get an E4 error message when I turn on the machine.


The first thing I would check is to see if you turned the water valve on under the sink. ... Danby DDW497W 22 in. Countertop Dishwasher

IDL700 wont start Kept getting error message to say there was a blockage. Checked all the pipes and pump, all fine. Now the blockage lights are out, but the machine wont start at all, just beeps when I press the start button, then nothing


Sorry to read about your problem, I hope this helps you out.the blockage, maybe inside the pump of the unit, or at the check valve.I suggest you contact a service company..I tried to help you. Please help me and Ra ... Indesit 24 in. IDL700 Built-In Dishwasher

On an AM15T the temperature goes to 130 degrees max and I was getting an error message (E2) I think. I replaced the rinse probe outside near the vacuum breaker. I don't get the error message anym


... Hobart AM15T Dishwasher

I get an LE error message on my LG Dishwasher. I replaced the pump. Still get the LE error. Replaced the main control. Still get the LE. No blockage in the pump. What now?


When you receive the LE error code, unplug the machine for approximately 15 - 20 minutes. This will reset the microprocessor.Oversudsing is the main cause of LE error codes. Using non-HE detergents or too much detergent will cause stress ... Dishwashers

I have an Electrolux EWDW6505G Dishwasher. Had started a cycle, then opened the door midcycle when water was in the tub -- and accidently pressed "cancel." When I try to start a new cycle now, I was getting an "Error 01" message. After trying to get out of it, I'm now getting a "water serv" message. How can I reset?


... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

I have LG dishwasher for 2 years now. Working perfectly until one day one glass gets broken during washing cycle. Immideatly we get EO error. We check possible reason of error in the manual then decided to try to fix ourself. We open bottom cover and drain outcoming part. Immideatly we discover a piece of glass that was preventing a small plastic piece to rotate. We remove that piece of glass. Put back covers and machine. We connected it back to outlets and run it. All was working again !!! This


In order to fix problem we disconnected dishwasher, put it on one of side, opened bottom cover - the one that is outside of dishwasher. We find out the part that is\015\012connected to the drain horse. We take of 3 screw and open that part too ... LG Dishwashers

Detergent error I keep getting add detergent message. The bottle is not empty, the pickup line is submerged in the detergent & it tests acceptable. i also get an E7 error code once in a while. Thanks


I'm a hobart tech---been away for awhile.What is the model lxih,lx30?Let me know if you still have a problem with it. ... Hobart 24 in. LXIC-5 Built-in Dishwasher

M/N PLD4555RFC3 I get blinking ER message with "wash" "dry" "clean" and "S" blinking icons All buttons have become non-responsive. Tried resetting by disconnecting power but error message comes back Only the Rapid cycle is now selectable. If I allow the unkt to cycle I end up with the error meesage above with the dishes only partially clean What could be the problem?


... Frigidaire PLD4555RFC Dishwasher

-keep getting error message LE -doesn't clean well if it does get through a cycle without error. -sounds like it starts and stops every few seconds.


Same problem as mine and unforutunety fix was a replacement motor which drives pump. Bearings were shot in motor. Lots of people have this problem. If you are good at repair you can buy motor on ebay for $60. Impeller will have to be removed ins ... LG 24 in. LDS 5811 Built-in Dishwasher

What does the F2 Error mean? I got that error thsi morning. The engine was buzzing so I turned the power off. I have cleared what appears to be calcium and/or soap build-up in the 3 filters and in the drain. When I turn the power back on I still get the F2 error. How can I restart the machine and turn off the F2 Error?


The F2 error means the tray underneath the unit has filled with water.\015\012You will need to pull out the dishwasher (remove 2 screws at top left/right when door open that prevent tilting).\015\012Unplug and pull out dishwasher.\015\012Remove 4 scr ... Asko D1876 Dishwasher

Error code OE; dishwasher stops with error message 2 min into cycle, drainage seems OK, water doesn't appear to pump into machine - any advice?


Hi,The most common cause of an OE error code on a modern LG dishwasher is: 1. Blocked drain hose 2. Obstruction in the sump area (beneath the filter, which needs to be removed to check for onstruction) 3. Failing drain motor.& ... LG 24 in. LD-12BW5 Free-standing Dishwasher

I cant get siemens dishwasher to work . An error E25 keeps appearing on the screen . What does this mean ? and how do I get rid of it and get machine to wash ?


... Siemens 24 in. SE20T590GB Free-Standing Dishwasher

No matter which cycle selection in pushed, the dishwasher only starts up in the "normal" 93 min cycle. If I try other cycle options, and persist, I get an ER message and the cycle stops prior to the soap powder door opening and never completes the cycle. Only with turning off power for several minutes and receiving the PF message, and resetting ONE TIME that message can I then select any cycle, at which time the machine "defaults" to the "normal" full cycle. If I do not disturb that cycle, it wi


Looks like you are having a good deal of problems with the dishwasher.\015\012\015\012It will be helpful if you provide the make and model no. of the dishwasher.\015\012\015\012At this stage I can speculate the controller (ass ... Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

I am getting an error message 002 on my Conia


... Dishwashers

SMU68 M05 AU/01 machine. I get an E-15 error & "check water" warning shows up. Have checked all hoses for kinks & all filters for blockages. All AOK


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

DW 955. F2 error still flashing after water has drained. Can't get machine to switch off this error.


... Asko Dishwashers

Hi i have a whirlpool dish washer - model : ADP4731/5 , AAA class . I keep getting a F7 error message and it is not allowing me to turn the washer on , if i hold the start button down it allows the washer to go for 30 seconds before the error comes back up and it stops working again


... Whirlpool Dishwashers

I'm having trouble starting my ge profile dishwasher; the machine locks but then when I push the start button one of three things happen: 1) I get error C3 and I do not have a user manual) 2) nothing happens 3 I get the screen indicating that the machineis a sensing soil level, washing' but in fact nothing happens - I do not hear the motor starting and no water runs, thank you!


... GE 24 in. Profile PDW7800 Built-in Dishwasher

I have a Bosch Apexx. When I turned it on all I get a is flashing message "Not started". The LED display on the top edge is not working - only the display on the face of the machine. I have tried holding the start button and pressing all the other buttons and the same message keeps flashing...what to do?


Looks like micro-controller problem. Contact service center. ... Dishwashers

IE message Getting an IE message on dishwasher. Water is coming into the tank and heating, but after about 5 minutes, it kicks into an IE error. We have checked the water inlet and the spray arms and everything appears okay. I have read the comments about checking the float, but how do you do this? Any other suggestions would be helpful.


My solution was, after LG sent me a second dishwasher that ALSO did not work, to demand a refund. Then I went and bought a KitchenAid~ it's awesome! ... LG LDF6810 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0755 seconds