Having problems with your Tecnik Dishwashers ?

The pump gets ride of water but wont turn off or start a new cycle


Answers :

You will have a leak in the sump of the d/washer. Pull it out and tilt it back about 50 degrees. water will form at the back on the floor. Place flat again then retry by starting a program. If it works, you know the leak is the problem. Mostly it is the main wash motor..
Repair Help & Product Troubleshooting for Tecnik Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The pump gets ride of water but wont turn off or start a new cycle


You will have a leak in the sump of the d/washer. Pull it out and tilt it back about 50 degrees. water will form at the back on the floor. Place flat again then retry by starting a program. If it works, you know the leak is the problem. Mostly it ... Tecnik Dishwashers

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

I have an Electrolux EWDW6505G Dishwasher. Had started a cycle, then opened the door midcycle when water was in the tub -- and accidently pressed "cancel." When I try to start a new cycle now, I was getting an "Error 01" message. After trying to get out of it, I'm now getting a "water serv" message. How can I reset?


... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

Bosch SMS4012 - E-NRSmS4012AU/11 FD7309041276not sure of its age but this dishwasher wont commence its cycle when I turn the left dial (but If I hold the handle latch up, it starts) there is no error code facility on this unit. Would it be worthwhile getting a technician to fix it or should i just buy a new one !! Thank you - Rena.


... Bosch Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Have a Westinghouse 905 dishwasher (guessing approx 5-10yrs old). When I turn it on it's starts is cycle as expected then stops after about 10mins and loses all power (can't turn it on or get any lights to light up for sometime almost like it needs to cool down) at this point the dishwasher is full of water. It is not the pump however as as soon as you can get power to it (sometimes some hours later) and turn it on the first thing it does is pump out the water. Any ideas??


It is likely the thermal relay is tripping. This could be because if you are feeding hot water to inlet the temperature of water is too high, or the dishwasher heater is faulty and overheating the water. Or it is also possible the thermal cutout is s ... Westinghouse Dishwashers

I have frigidaire dishwasher,starts cycle,can hear water entering dishwasher,checked level of water,does not get to 1",machine starts washing by the sound of motor, but dishes are not clean,water drains machine turns of,cycle complete.what do you think.


Depending on your dishwasher, it fills either by a timer or by a water probe or float. I will assume its a timer as a probe or float wouldnt exhibit this behaviour. I would say you have a restriction in your water supply line. Check your valves, an ... Frigidaire Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Brand new Hotpoint LFT 228 A. When I start a wash cycle, I get the initial beep, then can hear water intake, then humming (heater?) then get beeps once a second for 60 or so seconds, then then cycle seems to finish (drains water etc).


... Hotpoint Dishwashers

CI am having a problem getting our Miele G575 dishwasher to run through a wash cycle. It definitely has power, the water is on and there is no water in the bottom of the dishwasher. When you turn the dial to start a cycle, it hums but doesn't fill with water and doesn't progress through any cycle. We have tried all positions of the dial and have had no luck? Any ideas??


You said it does not progress...meaning the dial does not eventually move? it may be waiting on a water level sensor to be tripped. The dishwasher is just not filling. The water valve solenoid may be stuck or defective. or a wire may have come of ... Dishwashers

I have a Husky 2600 PSI power washer with the Honda GCV160 engine that I can't get to start. It was okay when I purchased it from Home Depot last spring but now I've tried putting new gas in it, spraying carb cleaner, new spark plug, and it still won't start. I only ran it for about 30 minutes when I first purchased it. The guy at the service desk at Home Depot told me that the water hose should be attached and turned on while trying to start. Is this true or would this be starting the motor und


You can eliminate the motor by unbolting the pump from it and then if it will start the problem is with the pump or the unloading valve.If it does not start with the pump removed then you check for spark and get the carb cleaned or have a kit put in ... Karcher 2500 PSI Pressure Washer

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

My dishwasher has power but does not turn on to any cycle when the control knob is in that position. It was adding water and starting to wash, but not going through the whole cycle and not rinsing and drying. Now it has water stuck in it. I hear sounds underneath like it's trying to go to the next cycle (a clicking noise), but then it doesn't. I put a new timer in it, but it was doing the same thing before that.


Hi just check out the following solutions that i provide u right now.. it will be a perfect fix for ur problem..\015\012\015\012\015\012\015\012\015\012\015\012first of all make this check\015\012 \015\012Door switch\015\012\015\012\015\ ... Dishwashers

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

Telmann dishwasher We have just moved into a new house with a Telmann TEL12DWMS dishwasher. The dishwasher will light up but wont start. Power and Rinse cycle lights light up but when you turn the dial it wont start. Any suggestions? Thank you


... Dishwashers

I have a Bosch dishwasher she44c05uc/40 It is 3-4 years old. Recently I noticed that the cycle times have gotten much longer. Since then there is a sewer smell in the washer especially when starting a new cycle it comes out of the disposal. I'm wondering if the pump isn't heating the water hot enough. I've also noticed that the dishes aren't getting near as clean as they were before all this started. Especially stuck on food. It used to clean everything now dishes almost need rinsed.


Hello,Welcome to FixYa ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Broken dishwasher It started when my dishwasher flooded my kitchen. I drained it and turned it on, it was fine. then it happened again. I have drained it then when I went to turn it on again it just sounds like it is running with no water. If I put water into the bottom it will drain but it will not fill up. I bought this house 3 years ago I am unsure how old the dishwasher, do I need to get a new one?


I have a kenmore model 665 168 29000 the mounting bracket have broken from under the cabinet, so when you open the door and pull the racks out the machine moves forward, how can i fix this????? ... Bosch 23 in. SHU33A Built-In Dishwasher

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed.


Do you have the manual?What is the exact model #?Thanks~! ... Dishwashers

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed. Model #SHU5314UC/U06 FD#8001


Test the door switch. It can be faulty or misaligned. You can also check the back of the unit and/or remove the rear panel and take a look at the thermal fuse. It may be bad not allowing enough current flow to operate the machine. ... Bosch SHU5316UC Dishwasher

My dishwasher was recently 'installed'. i don't know if the contractor made a mistake or if the water valve is not turned on, but the cycle tries to start but then no water is flowing into the dishwasher. everything appears to be hooked up, but I think it's the water issue b/c i also have a new refrigerator and the water dispenser/ice maker does not work because no water is flowing into the fridge either.


This sure sounds like a water valve issue, for sure. You will have to trace out the lines (not easy, but possible) and figure out where the valve is. They usually turn left to open, and right to close. I would call the contractor and tell them ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

DISHWASHER WONT GO INTO WASH CYCLES,WHEN I PUSH START GOES CANCEL/DRAIN,CAN HERE PUMP RUNNING THEN IT WILL TURN OFF,THERE IS NO WATER IN THE BOTTOM,SEEMS LIKE STUCK IN DRAIN CYCLE


... Whirlpool GU2300XTS 24 in Builtin Dishwasher

We have a GE GSD4000J00WW dishwasher, 2 yrs old. Suddenly seems to fill with water, but no motor engages when you start the cycle. When you turn the knob, it makes a clunking sound, but all that happens is water fills. Also, how do I get the water out of the bottom of the dishwasher now? Thanks!


... GE Dishwashers

I have a bosch SHU6802UC dish washer. Recently the cycles were getting very long (3+ hours) and now when you press power/start, the unit turns on and you can hear the rather loud hum (pump?) of the cycle starting but it does not do anything else, just continues the loud hum. No cycle, does not fill with water, nothing. I ran the diaognostic and it immediately came up "7" on the display. Any thoughts or direction would be greatly appreciated. FYI, I did thuroughly clean it which made no di


There are a few possibities...if you remove the lid and take the two t20 screw off the left side panel at the front you could check the pressure chamber and its hose are not blocked. Use the link and go to page 4, part 263834 and 361113. You ca ... Dishwashers

My De Dietrich dishwasher turns on but then turns off after a couple of minutes with no water entering dishwasher. I found some instructions and turned on and off 5 times (and unplugged). This worked once and full cycle ran but not the second time. Not sure if it is worth paying 165 call out charge or getting new machine as 7 years old


... De Dietrich 23 in. DVF110J Built-in Dishwasher

Hi, my beko DE 2542 FS dishwasher wont start a wash cycle when i turn it on it makes a noise briefly, then nothing. iv taken the hose off and the water drains out so its not blocked. any ideas??


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2194 seconds