Having problems with your Tricity Bendix 18 in. DH090 Free-standing Dishwasher ?

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


Answers :

Repair Help & Product Troubleshooting for Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

I have a problem with my Asko D3350 Dishwasher, can you help? On startup the diswasher does its normal cycle and pumps excess water out and then fills the dishwasher with water to the correct level of water, after this the machine has no dishwashing action at all for the duration of the program setting. The dishwaher then pumps all excess water out and switches off as normal but no washing action has taken place, there are no error codes during the entire operation. Is there any way to rese


Hi Tony,\015\012\015\012I have the same machine (D3350) and almost the same problem.\015\012\015\012Mine starts each cycle fine - pumps out - fills - rinses - pumps out tht first load and then does not fill again. If I manuall ... Asko Dishwashers

Smeg DWF612WH dishwasher has developed a leak. Water comes out of the rectangular hole on the side of the water softner used to mount what looks like a level or pressure switch. A few seconds after the fill valve opens water leaks out, not a lot just a small trickle. After the washer has filled and goes ito its cycle, it does not leak again. Over the past weeks the problem has got progressively worse.


... Smeg 24 in. DWF612WH Free-standing Dishwasher

Any of the programs start ok (water enters etc..) but the program does not move on, will stay at the same place early in the program cycle for hours. You can move the program on manually and the water ext will exit but the dishes are not properly washed. Changed program timer switch but still same - zdi6041x dishwasher - any idea why ?


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Zanussi 23 in. ZDI6041 Built-in Dishwasher

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

Got a Indesit Di620 Dishwasher that trips RCD after power up & immediateley as you shut door.Fault is definately related to pressure switch, disconnected pipe to switch and then able to start cycle, without tripping, small amount of water out of pipe,but cycle only lasts for a few minutes, then stops. ( blowing into pressure switch trips rcd )How can i test switch, or is it a water level problem ??Any help would be good, thanks S.C


... Dishwashers

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

Dishwasher Water is not going through upper and lower spray arms. Checked overfill protector switch, inlet valve, inlet valve screen, pump blades move freely, Pumb motor is working , Water enters into machine but does not go throught spray arms. Water heats up, Machine will go through all cycles but without water going through spray arms. 650 / 690 series gldb656jso


... Dishwashers

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Insufficient water during some cycles;drains prematurely at times


... GE Dishwashers

Dishwasher cycles with timer, won't fill with water. Motor runs fine, drain and fill valves test fine, float switch tests fine too. Water pressure fine. I'm thinking the timer is bad and won't send a signal to the water valve to open. What do you think? The system here doesn't know what a GSD2030F00WW is, so I had to pic one with a computer board, mine is not that sophisticated.


Remove the toekick plate on the bottom of the dishwasher.Remove the wires from the water valve. Insert the leads from a volt meter into the water valve power wires.Turn the washer on. After the initial pump out cycle the timer sends power ... GE 24 in. GSD2030Z Built-in Dishwasher

My Whirlpool Gold Series 980 dishwater no longer fills up with enough water to drive the washing arms, so the dishes do not come out clean. I cleaned the filter on the water intake valve (which was really clogged) and it still did the same thing. Replaced the inlet valve and still no change. The water does not reach the level of the overfill float switch, so that’s not it. Its been working fine for 4-5 years, what else could it be? Thank you.


I hve provided u with all details .read it carefully .it has all the resolutions for all possibilities ... Whirlpool Dishwashers

My dishwasher only fills half way and it dosn't go through the wash cycle. It pumps the water out and then go to the rinse cycle but has the same problems with the water level. We have checked the motor, pump and the water valve. It seems to be working fine. Thought it might be the timer.


Hi,\015\012\015\012This is an issue with the wash motor..\015\012There are two motors,a wash motor and a drain pump/motor assy\015\012The wah motoe must have been the issue with the case.Changing the wash motor will solve your ... Dishwashers

My Kitchenaid ModelKUDI01TJBL0 only leaks at initial start up. Just after the water fills, the first few seconds of the wash cycle. It pours out the front door for a couple seconds than no more for the rest of the wash. It is level, no cracked arms, or loose pumps.Splash guard is in place. The float seems to be working, not too much water in the bottom. I am stumped. Although I do feel that it has something to do with the level of the water being too high, when the arm starts turning, it makes a


Is the unit level or leaning back if leaning back it is morelikey filling too much if level make sure the float moves up/down easy if not clean ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Hi I have a Neff built in dishwasher s5453X1GB/70 about 4 years old. Never had a problem before. Came downstairs last night to find the kitchen floor flooded. Water also still in machine. But must have been near end of cycle as plates all clean. I have read other links and opened pump compartment in centre of machine and syringed out all water and cleaned fan. When i switch on machine it is still making odd humming noise (emptying cycle?) I have read about anti -flood valve etc. Any more tip


... Dishwashers

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

I am trying to fault find a Hobart AM15 ML-130038 dishwasher. Wash cycle does not start automatically after the water level activates the level switch & energizes the contactor? To get the wash cycle to start you need to open and close the door.


... Dishwashers

When I start the wash cycle it does not get any water, but will continue through the entire cycle. I have checked and replaced the water valve, check teh float and float switch. The handle is working correctly. The selector panel is all elcetronic and I do not know what else to do to trouble shoot. Any help??/


I would first check the water valve is it turne on? then are you getting power to the water valve ? if not problem might be in electronic panel. ... Dishwashers

Normal wash cycle- tub fills (?), then comes a loud hummmm and nothing happens. I noticed water level didn't reach heater coil and added water until limiter switch clicked. Still just a loud hummmm. Machine was well into its regular cycle when this first occurred, but now, won't even get past initial fill. Pushing the "Cancel/drain" button activates motor and pump: they work fine.


You are an expert enough reading this. But with a terrible complicated dishwasher. First clear the waterlevel problem.\015\012Rest is a result. You do not need me, join us. Next time buy something more plain. ... Dishwashers

Bosch shv57c dishwasher will not fill with water. Replaced the fill valve(no fix). Drain cycle works fine. When rain cycle ends clicking is heard but no water fill. Trying to locate float and float switch. can you help with their locations? San


... Bosch 18 in. SRS45E02 / SRS45E08 Exxcel Slim-Line Free-standing Dishwasher

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2026 seconds