Having problems with your Troy-Bilt XP 3000 PSI 2.7 GPM Gas Pressure Washer 020489 ?

Pull cord stuck Troy bilt 3000 - Troy-Bilt XP 3000 PSI 2.7 GPM Gas Pressure Washer 020489


Answers :

Repair Help & Product Troubleshooting for Troy-Bilt XP 3000 PSI 2.7 GPM Gas Pressure Washer 020489

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pull cord stuck Troy bilt 3000 - Troy-Bilt XP 3000 PSI 2.7 GPM Gas Pressure Washer 020489


... Troy-Bilt XP 3000 PSI 2.7 GPM Gas Pressure Washer 020489

Troy bilt 2600psi 2.3gpm model 160 pressure washer, I hooked everything up like normal, It cranked up fine, when I pulled the trigger on the gun it stalled. When I try to crank it back up the cord wont even pull like its stuck any suggestions would really help me tks..


This sounds like the pump has dead headed. I.e. the unloader valve is sticking. Unhooking all of the hoses should eventually allow everything to free up. Once it is free what you should do is add about 3 ounces of oil into the water inlet connecti ... Pressure Washers

Water in the oil - Troy-Bilt XP 3000 PSI 2.7 GPM Gas Pressure Washer 020489


Sounds to me lyk it needs a new gasket ... Troy-Bilt XP 3000 PSI 2.7 GPM Gas Pressure Washer 020489

Motor starts but shuts down immediately - Troy-Bilt XP 3000 PSI 2.7 GPM Gas Pressure Washer 020489


Hi ted6565\015\012Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.\015\ ... Troy-Bilt XP 3000 PSI 2.7 GPM Gas Pressure Washer 020489

My neighbor just gave me a Troy Bilt 020207 power washer. It is 2450 PSI and 2 GPM. He snapped the pull cord rope. I looked at the pull cord cover and it seems to have 3 rivets holding it to the main housing. How do you recommend to repair or replace the pull cord?


Sounds like a briggs engine, DONT remove the rivits, go down a little further and remove the 4 3/8 bolts that hold the blower housing on.Turn it upside down, prewinf the pulley in the direction that it turns when the rope is being pulled. When it sto ... Briggs & Stratton Pressure Washers

Troy bilt pull cord pressure washer recoil - Pressure Washers


... Pressure Washers

I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new


Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer

2500 PSI 2.3 GPM Gas Pressure Washer - Troy-Bilt Pressure Washers


... Troy-Bilt Pressure Washers

Gas leaking out of carbuerator - Troy-Bilt 2700 PSI 2.3 GPM Gas Pressure Washer CARB 020487


... Troy-Bilt 2700 PSI 2.3 GPM Gas Pressure Washer CARB 020487

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

Troy-bilt pressure washer 3000 max psi 2.7 gpm not getting gas


The carburetor ports and jets are likely clogged with gum from fuel that contains Ethanol. Avoid using any gasoline that contains Ethanol in small engines. Use only 100% gasoline. You can try the simple method first by adding some Lucas to the gasol ... Briggs & Stratton Pressure Washers

Troy bilt pressure washer deadheaded - Troy-Bilt 020528 Gas Pressure Washer


... Troy-Bilt 020528 Gas Pressure Washer

Troy-Bilt 2700 PSI 2.3 GPM Gas Pressure Washer will not start


... Karcher Pressure Washers

Troy-Bilt 2700 PSI 2.3 GPM Gas Pressure Washer (CARB) service manuel


... Karcher Pressure Washers

Need operators manual - Troy-Bilt 2700 PSI 2.3 GPM Gas Pressure Washer CARB 020487


Http://www.troybilt-gen-pw.com/manuals/index.cfm?rd=1go to link and download ... Troy-Bilt 2700 PSI 2.3 GPM Gas Pressure Washer CARB 020487

Troy-Bilt XP 3000 PSI 2.7 GPM Gas Pressure Washer


... Honda Pressure Washers

Replacement pump for Troy-Bilt 2600 PSI 2.3 GPM Gas Pressure Washer


... Troy-Bilt 020528 Gas Pressure Washer

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

Troy Bilt Pressure Washer Model 01902 Leaking Gas from Air Filter


Try banging lightly on carberator with block of wood or something to free up float and valve!!!! ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Troy-bilt gas Pressure Washers won't start - Pressure Washers


... Pressure Washers

Oil plug on troy bilt 020240 pressure washer - Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Troy bilt pressure washer 02033 gas tank - Honda Pressure Washers


... Honda Pressure Washers

2800 PSI Troy-Bilt XP pressure washer manual - Briggs & Stratton Prosumer 20324 Gas Pressure Washer


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

On off switch for troy bilt pressure washer - Briggs & Stratton Prosumer 20324 Gas Pressure Washer


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1150 seconds