Having problems with your Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher ?

TIMER DOES NOT ADVANCE

\015 Yesterday while running he dishwasher I smelled something burning comming from the doof of the dishwasher. The timer would not cycle ofter that. I replaced the timer $ 108.00 and installed it and it still does not cycle. I am getting 5.6 volts when the power is on and going to the timer. It doesn't see enough. Is there somthing else in the circuit that is preventing the timer from cycling. HELP!\015\012\015\012Thanks\015

Answers :

Mr. marconi,
\015\012
\015\012it looks like i have the same problem.
\015\012
\015\012at the end of the cycle the machine keeps draining and never finishing.
\015\012
\015\012where can I buy the timer for $108.- ?
\015\012thanks for helping.
\015\012
\015\012behmoaras
\015\012[email protected]
At the point where the wiring comes from the bottom of the tank and rises up the door is prone to burning. Before doing the following remove power from your dishwasher. By removing the kickplate at the front and inspacting the bundle of wires you may note that some of the wires are lumpy or burned. These wires need to be repaired. Failing that there is a cycling thermostat mounted to the bottom of the tank above the water valve. These cycling thermos will prevent the timer from advancing there should be a wiring diagram inside of the door that will help your efforts.
Repair Help & Product Troubleshooting for Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

I have a Bosch SMU2046UC/14 dishwasher that makes some noise but will not start the wash cycle. I found that the noise was from the timer motor by removing the front of the door. The timer continues to run and but only advances until half way through the wash cycle where it stops permanently. Is this a problem with the timer or could something else be causing this problem.


HI. The timer motor mechanism regulates the length of time power is to be routed to each component. If the timer motor does not advance properly, it can result in a wide range of problems. Common symptoms will usually include sticking in a cycle(fail ... Bosch 24 in. SMU40 Built-in Dishwasher

Dear sir In an attempt to dislodge a blockage of my sewer line using Draino and a plunger some of the Drano ended up in the dishwasher and now the dishwasher will not run. My dishwasher is a SHU3036UC/U12. When starting the unit up it empties the unit but the cycle newer ends, in other words the timer does not advance to the next cycle, I have determined that the timer motor works by removing it from the unit and supplying it with power. One thought is, can the water level switch be stuck in


HiCheck this video and clean the drain pump assembly: ... Bosch SHU3036UC Dishwasher

Timer Timmer dose not advance. I have replaced the timer and it still has the same problem.


Check the pin connector between the touchpad & control board and ensure that it's seated correctly in the slot on the control board. if this does not solve the problem replace the control board. ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Dishwasher has very very long run cycle. Dishes come out hot so I'm assuming the water is heated enough, & T stat tests ok. Seems if we advance timer manually it will finish otherwise seems to stay about in the center position on timer.


... Bosch SHU3036UC Dishwasher

Dishwasher timer stops at 28 min but dishwasher still run and timer does not advance


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Asko 1716, the program will not advance. I changed the timer mechanism but that had no effect. There is no water leaks and the if i manually move the timer it seems to perform that cycle: water enters the machine, it will wash and will also drain the water out. any clues?


... Asko D1716 Built-in Dishwasher

Dear sirs, we need to buy AKO timer 513 316. Our timer is damaged and we need spare part for washing machine. thank you in advance best regards Aleksandar Perinovic


... Dishwashers

Hello, my Hoover D7610 dishwasher has developed a problem, I would appreciate your advice.On starting a wash it appears to be working OK through what I believe to be a rinse cycle but then after about 20 minutes water pours out from the bottom of the door. Manually clicking the timer-programer forward stops the leaking but the machine needs manual advancement except for the last 2 cycles when the timer seems to work OK. After the 1st cycle there is no more water leaking from the machine but all


... Hoover Dishwashers

Dishwasher won't fill. replaced fill valve assy. checked float switch it's ok. timer seems to be cycling properly but i'm not getting power to fill valve solenoid. Is it the timer or advance module? and how do I test?


Since you are this deep into the machine, it would be easy to tell if that is the issue by using a meter to test for continuity THROUGH the switches on the timer. It might be the power supply is not working right to send the voltage to that switch. ... General Electric WD21X10013 TIMER

Bosch SHU3032UC/UC12 Timer won't advance and pump motor runs


... Dishwashers

Whirlpool dishwasher du912pfgq1, timer will not advance


Does sound like a timer issue, valve obviously works(fills in rinse) timer not advancing, ( sometimes can be from the timer knog hitting against he console itself, try pulling the knob out a bit, eprhaops its getting stuck.) looked up the timer 8 ... Whirlpool 24 in. DU900PCD Built-in Dishwasher

GE GSD2030 Dishwasher, Timer not advancing


... GE 24 in. Profile PDW7800 Built-in Dishwasher

Timer does not advance water stays cold model number kd12ww


... Kelvinator Dishwashers

Maytag timer won't advance.


... Maytag Dishwasher

The timer knob does not advance


Replace the timer\015\012\015\012 ... Kenmore 18 in. 14432 / 14439 Built-in Dishwasher

Dishwasher Timer won't advance


My timer has stopped functioning altogether. it was first an intermittent problem, but is now 100%. ... Dishwashers

GE Nautilus timer will not advance


... GE Nautilus 24" Built-in Dishwasher

TIMER DOES NOT ADVANCE


Mr. marconi,\015\012\015\012it looks like i have the same problem.\015\012\015\012at the end of the cycle the machine keeps draining and never finishing.\015\012\015\012where can I buy the timer for $108.- ?\ ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Viking Dishwasher Timer Dial not advancing


The timer has given it up.  The motor has probably stopped working or the gears are jammed.  You'll need to obtain and change the timer.  Generally, there are face mounted screws that may or may not be behind some covers.  Remove ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Washing machine stopped after wash cycle would not advance to rinse cycle. Tried all the cyclyes manually and it only makes a humming noise from the top part of the machine by the timer.


Could be a bad water valve. ... Kenmore Series 80 Creme Top Panel

Timer not advancing, heating element working


I would recommend replacing the timer ... Kenmore Dishwashers

Miele 868 dishwasher-water fills at begin of cycle,but pump/wash cycle doesn't engage(timer dial still advances,drains at end of cycle.dishwasher was workong,but was moved to a new location ans hasn't worked since.impeller moves freely and pump was rotated via 8mm hex key.is there possibly a reboot/reset, or is there possibly a water pressure issue?-I didn't think so as the dishwasher fills to the prescribed level.


... Miele Dishwashers

I have a bosch Exxcel slimline, nearly three years old. Last night it ran all night on a 119 minute programm. It was stuck on 1 minute. Now I acnt get it to start on any programme. It starts up ok nut the timer doesn't advance at all! I checked the pump, that's ok and cleaned out the food filters, reloaded salt and rinse aid.


I have a bosch exxcell about 3 yaers old the program gets stuck on 120 all night whats wrong ... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

My Bosch SMU2000 series dishwasher will not complete the wash cycle. Advancing the dial completes the cycle but it sticks again before completing the rinse cycle. I replaced the timer assembly and the symptoms are the same


Hi,It seems to me a Faulty Control Board. You need to pull up the control board and check the resistors on it. If found burned or swelled, needs to replace those.Note - It's better to replace control board than to repair as yo ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0316 seconds