Having problems with your Viking Designer Series DFUD140 (Ultra-Premium) Built-in Dishwasher ?

No water, sounds normal . might be silenoid switch on inlet valve? vud140 viking dw


Answers :

We have a Viking Designer Series 140. It appears the upper rotating arm is not rotating. We checked the basicsclogs, etc) but are unable to rectify the problem. Any ideas?
\015\012[email protected]
Could be the water valve silenoid connection clip to the power source has been disconnected, 2) water valve is clogged with debris, 3) water valve silenoid has gone bad. I think one of these three things may be your problem. Good Luck
\015\012
\015\012Dave
Repair Help & Product Troubleshooting for Viking Designer Series DFUD140 (Ultra-Premium) Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No water, sounds normal . might be silenoid switch on inlet valve? vud140 viking dw


We have a Viking Designer Series 140. It appears the upper rotating arm is not rotating. We checked the basicsclogs, etc) but are unable to rectify the problem. Any ideas?\015\012 ... Viking Designer Series DFUD140 (Ultra-Premium) Built-in Dishwasher

Power light together with 'Intensive', 'Normal' and 'Soak' lights all flash in unison towards end of wash cycle with a gurgling sound from the pump suction that doesn't stop until the power is switched off. Water inlet filters all cleaned with no affect.


... Hotpoint Dishwashers

Unit will not drain. It will fill with water in normal manner. Circulating pump also works normally. Float switch seems to be sound. But the wash water is not expelled as it ought to be.


Something simple to check is the drain hose. I am an installer and have seen this many times and people will buy a new dishwasher after putting in a new garbage disposal. If you did, did you remove the knock out plug from the disposal? Next, remov ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Hi, my dishwasher is a GE model PDW9280l00SS. Problem is water comes out of spinner arms but they dont spin, water presure is good too the sink. same hook up.I get thumping sounds from the inlet hose.I opened the door and pushed the switch in to watch the water to the arms hardely no water coming out.


... GE 24 in. PDW9280LSS Built-in Dishwasher

My Bosch Classixx (about 10 years old) dishwasher won't fill The problem has only started since I pulled it out and cleaned! The programme sounds are as normal but no water enters the machine. I detected a small leak on the inlet pipe and tightened that. The machine drains when I add water manually though it has made a lot of gurgling noises for some time now when draining. When tipped on its side water comes out of the bottom of the machine (not entirely clear but not dirty either). When upri


... Bosch SHU9915UC Dishwasher

My Dishwasher stopped working. When I switch it on there is a sound like a motor running, a kind of whirring sound. It sounds as if the machine is working normally but there is no water coming through it. Any ideas? Thanks, Paul


Hi There,\015\012\015\012That's the classic sign of water having leaked under the washing compartment/tub. This causes a "float" to rise, tripping the micro-switch which activates the anti-flood protection. This closes the water inlet val ... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

My Bosch diswasher water inlet work fine, when the wash motor or cycle need to start nothing happens. The timer is advancing normal. Water outlet(drain pump) is also working fine. There is no woosh sound (start of wash cycle) and arms is not rotating.


Hi,\015\012\015\012it sound's like the wash motor is either seized or just stuck, let's hope it's the later. Bosch had issued a service tip about this problem several years ago titled "Loosening Frozen Impellers" strange choice of word's considering ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

My Bosch Classixx is not filling with water and no sound of the pump trying to work either. I fiddled around with it as it was not cleaning bowls properly on the bottom shelf - plates and cutlery were fine! Think I might have disturbed the round dome thing - is this the "float switch"? There is also about an inch in the bottom of the filter area which I have cleaned out of gunk but still with water there. Any ideas please!


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

My Whirlpool ADP 553 dishwasher starts and time switch goes through normally but nothing happens. The only thing is it does try and drain previous water. I suspect the inlet valve to be faulty thereby not letting water in. Could this be the fault


... Whirlpool 18 in. ADP530 Free-standing Dishwasher

Hi there Why is my dishwasher not letting water in? I switch on the machine as normal and all sounds perfect except no water is entering the machine?


The most common problem is with the water valve. It may be defective, and hence not letting enough (or any) water in. ... Whirlpool Dishwashers

Bosch Exxcel Dishwasher model SGS56E02GB/47 When you switch it on no water is coming through - what sounds like the pump/motor sounds a lot rougher than normal and there's a very very faint electrical burning smell. The timer counts down, but it never appears to do anything and continues doing so after the counter has zeroed.


... Bosch Dishwashers

Dishwasher model: se6 tie1 Fitted under kitchen work-top. Problem: After setting a program & switching on & closing door ? there is a normal sound from within but if door is opened there is no evidence of water being pumped in. I previously cleared food debris from the drainage pump area (including under the pump cover), checked the spray arms and checked the water supply was getting as far as the long in-take pipe. As it seems problematic to remove the (screwed in) dishwasher, I have not che


... Dishwashers

Flashing then solid water intake light. I have cleaned the intake filter it seems to me the dishwasher is either got a bad switch to the inlet or the program the ends a drying cycle is stuck on. it sounds like that sound


I think your assumptions are pretty close. The filtersensor may be faulty too. If you feel up to it you can do it yourself, but it would be faster to have a appliance guy to do it., ... Dishwashers

Dirty dishes The dishwasher does not wash the dishes properly seems to make all the normal noises but when finished its cycles the dishes are still dirty. Reading some of the other reviews sounds like I might have a inlet valve problem. Is there any way i can test if the inlet valve is functioning properly.


If water comes into machine then valve is ok.\015\012open machine when in cycle and look to see if spray arms are rotating\015\012if not, then take out and clean.\015\012spray arms only rotate with water jetting out of angled nozzle ... Dishwashers

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

Telmann Dishwasher TEL 12DWM. Dishwasher started to make weird wooshing start-stopping sounds at the beginning of the wash cycle so I stopped it. Since then the lights are on but wont go regardless of where the switch is set to. Have pulled the pump off and the inlet pipes and blown to remove any blockage but still no luck. Cant get into the water jet part due to connectors that require specfic tools to remove and replace. Any thoughts?? thanks in advance, Michael


... Dishwashers

I have an kenmore elite "ultra wash" model 665. not sure the rest.. about 7/8 years old, making loud buzzing sound during wash cycles,starts about 5 minutes into the normal wash cycle. i removed the inlet protector and the chopper area and all was clear.clean...it's running now and seems to be pumping the water, but can live with this buzzing noise,,, any idea, is the pump on it's way out ? just stopped as it kicked into another cycle, at 42 minutes...but it will be back, any ideas ? (back alrea


Buzzing sound may be coming from a solenoid that is mounted under the dishwasher, below the tub ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

Hi :) We have a Bosch slimline dishwasher type SRS56A02 GB/08 - it doesn't draw in water - the timer counts down but nothing happens. We checked these pages and cleaned the filters on the inlet water line but no change :( I saw that it might be the inlet water valve - is this easy to get to - do we need to take off panels? if so, is there a manual available please? Over the past week or so it had got noiser - it was at its quietest while the water was draining out of the machine.


... Dishwashers

I have a problem with my Asko D3350 Dishwasher, can you help? On startup the diswasher does its normal cycle and pumps excess water out and then fills the dishwasher with water to the correct level of water, after this the machine has no dishwashing action at all for the duration of the program setting. The dishwaher then pumps all excess water out and switches off as normal but no washing action has taken place, there are no error codes during the entire operation. Is there any way to rese


Hi Tony,\015\012\015\012I have the same machine (D3350) and almost the same problem.\015\012\015\012Mine starts each cycle fine - pumps out - fills - rinses - pumps out tht first load and then does not fill again. If I manuall ... Asko Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

Dishwasher Water is not going through upper and lower spray arms. Checked overfill protector switch, inlet valve, inlet valve screen, pump blades move freely, Pumb motor is working , Water enters into machine but does not go throught spray arms. Water heats up, Machine will go through all cycles but without water going through spray arms. 650 / 690 series gldb656jso


... Dishwashers

GE model#vrb4119vw129 My water inlet valve wont stop pumping water after the tub is full. I have replace the water inlet valve and the float switch.


... Dishwashers

Dishwasher not taking in water and then huming sound and bleeping sound but it wont work. have switched water on /off in case of air lock and have replaced fuse in wall. was working and went through last cycle ok but left little water in the base of machine. soaked this uo and tried all of above. Please help!


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the l ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1746 seconds