Having problems with your Viking DFUD042 Built-in Dishwasher ?

Viking dishwaser turns on, but I can tell that it is not cycling.

\015 It turns on and doesn't cycle and shuts off in a couple of minutes. Water remains in the bottom of the dishwasher. I pulled the filter out of the bottom and it is clean. \015\012\015\012Tried all of the different settings, but nothing changed.\015\012\015

Answers :

Check the following to address this issue.


1. Air gap / Drain hoses
\015\012If there is an air gap (located in the sink, near the faucet), check to\015\012see if it is clogged. Unscrew the top cap and see if there is anything\015\012blocking inside. Note: If there is no air gap installed, the dishwasher\015\012might not drain properly.
\015\012\011\011\011
\015\012If the drain hose is clogged, the dishwasher would not drain. If there\015\012is an air gap installed, it is very common that a hose going from the\015\012air gap into the garbage disposer is clogged. Remove and clean the\015\012hose. Make sure to reattach the hose before starting the dishwasher.
\015\012\011\011\011
\015\012\011\011\011Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.
\015\012\011\011\011
\015\012\011\011\0112. Broken belt
\015\012\011\011\011Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.
\015\012\011\011\011
\015\012Note: Sometimes the belt would just come off the pump. Even though it\015\012might not be broken, it is recommended that you replace the belt,\015\012because it is probably too stretched out.
\015\012\011\011\011
\015\012\011\011\0113. Pump
\015\012Some models have two impellers inside the pump - one, wash impeller,\015\012takes care of the wash cycles, the other, drain impeller, drains the\015\012water out. If the drain impeller is broken (broken blades, shaft), the\015\012dishwasher would not drain. Replace any broken pump components.
\015\012\011\011\011
\015\012\011\011\0114. Drain solenoid
\015\012Some models (for example most GE dishwashers) use a drain solenoid to\015\012drain water out. Sometimes the solenoid gets stuck, preventing the\015\012water from draining out. Try to free up the solenoid. If unsuccessful,\015\012you might have to replace the pump assembly.
\015\012\011\011\011
\015\012\011\011\0115. Motor
\015\012\011\011\011If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.
\015\012\011\011\011
\015\012\011\011\011Replace the motor if defective.
\015\012\011\011\011
\015\012\011\011\0116. Timer
\015\012\011\011\011Replace if defective (note: uncommon problem).\015\012\011\015\012 \015\012\011
Repair Help & Product Troubleshooting for Viking DFUD042 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Viking dishwaser turns on, but I can tell that it is not cycling.


Check the following to address this issue.1. Air gap / Drain hoses\015\012If there is an air gap (located in the sink, near the faucet), check to\015\012see if it is clogged. Unscrew the top cap and see if there is anyt ... Viking DFUD042 Built-in Dishwasher

Re: bosch-integra-500-shx45p05uc PEASE, please, tell me how to turn off the annoying signal that comes on at the end of the cycle!!!!! Who had the big idea to add this feature and what is so important about being alerted when the dishes are clean? And if it can't be turned off, is there a way to disconnect the wiring and disable it? If so, how and if not, is it legal to shoot your brand new dishwasher or throw it out the window? Thanks so much!


... Bosch Integra 500 SHX42L15UC 24 in Builtin Dishwasher

My Viking dishwasher (~2 yrs old) won't complete a cycle - it continues to run unless I run unless I turn the power off. It also doesn't drain when I change cycles like it's supposed to. I've cleaned the filters and removed the dishwaher to check drain line for kinks and to ensure it not clogged. Any other suggestions?


If is continueously running because the unit is trying to get rid of the water in this instance shut off the water and shut off the electrical breaker disconnect the drain hose and assure that there is nothing blocking the end of the hose that goes t ... Viking DFUD042P Built-in Dishwasher

Hobart lx18h Our commercial Hobart dishwaser stops working after running a few cycles. After pressing start the LED display will continually blink and nothing will happen. We'll turn it off and on again a few times to reset it and it will start up again eventually. We've had an appliance guy look at it multiple times. He's replaced a part or two for it but the problem continues and he isn't much help. Anyone else had any similar issues with this model of dishwasher?


... Dishwashers

No water my kenmore dishwasher is not getting any water. when we try to select normal wash or water miser cycle, the motor turns on, I can tell water is getting to the dishwasher because i can hear it running under the sink and feel it in the flexpipe that feeds the dishwasher. It is not getting anything inside though. Just wondering if you have any ideas. Thanks


SOUND LIKE YOU HAVE EITHER A FLOAT THAT IS STINKING OR A WATER INLET VAVLE THAT HAS FAILED. THE FOAT IS THE LITTLE MUSHROOM LIKE DOME WHICH IS PLACED AT THE FRONT LEFT SIDE UNDERNEATH THE BOTTOM RACK PULL UP GENTLY ON THE FLOAT UNTIL U HEAR A CLICK ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Viking Professional Dishwasher - dfud142 pump continues to run during drain cycle will not shut off when door is opened have to unplug to turn off


More than likely the door saftey switch is broken, check your owners manual ... Viking DFUD142 Built-in Dishwasher

In normal wash dishwaser filles startes to wash but doesn't change cycles will pump out only when i turn to drain/off


... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher

I removed an old dishwasher and replaced it with this GE 24" Profile GSD533ODO1WW unit. It seems to run through the cycles like it should but it doesn't seem to run any water for some reason. I hooked up a new water line to it and turned it on. There where no leaks that I could see. Is there any installation manual that you could send me to make sure that I didn't miss anything or is there anything that you can tell me that I should look for? Thanks, Jesse


... Dishwashers

I have a Bosch SHX43M05UC Dishwasher. To wash, you select the cycle and then close the door to start the wash. Now when I push the on button, the pump turns on. I can't tell if it's pumping water or not but it's not supposed to start until the door is closed.


... Bosch SHX43M05UC Built-in Dishwasher

My haier compact counter top dishwasher model # HDT18PA turned off mid-cycle and wont turn back on


... Haier Best prices HDT18PA Space Saver Compact Countertop Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


Your touchpad is likely faulty. Sometimes called a control panel. You can get parts, manual, pictures, part numbers, and more at partselect.com or repairclinic.com ... Dishwashers

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


The electronic control board is most likely the issue. I would replace the pab that controls the dishwasher functions. The control board controls the cycles and the wash time selection as well as the on/off function of the dishwasher. ... Dishwashers

I turn on my dishwasher and press regular cycle and try to start a cycle but pressing start does nothing. I am unable to change cycles to anything other than the regular cycle and I cant start. Have turned off and on. Ideas?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

Hi. Our DS603I dishwasher starts on the Rinse cycle on its own - it beeps, red light flashing and no water entering the tub. It does this even if it is open. Similarly, when we try to turn it on to do a normal or heavy cycle, it starts (making quiet a loud noise) and then goes to the Rinse cycle, beeping, red light flashing, no water going into the tub. The pump wheel is turning. We can't find any blockages in the tubes. We have power-cycled it many times. Please help!


Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012\015\012\015\012\015\012 ... Fisher DS603W / DS603B / DS603I Dishwasher

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

Hi, I have a fisher and Paykel double dish drawer model DD605. A couple of days ago when we opened the top drawer all the lights flashed and beeped in sequence repeatedly and would only stop when the power was turned off or the dishdrawer closed. Today I went to turn the top dish drawer on and cannot change the cycle off rinse. I can push the eco button and the rinse cycle works no problem but I cannot change the cycle. The bottom drawer is running as I write this and appears to be fine. An


Hi\015\012\015\012\015\012Could you please let me know which all lights are blinking/lit solid in sequence from right to left. This could be an issue of drawer lock mechanism or flood switch issue. PLease post back with detai ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My dishwasher dial will turn but not by itself and it won't go through a cycle, it seems to be stuck on a wash cycle. I can turn it off but it has standing water in it because the cycle didn't finish.


... Kenmore 15529 Built-in Dishwasher

The dishwasher pump sounds like it is trying to drain, even when the stop button is pressed and the door is opened. The only thing that stops it is turning the power off at the power point. However, when the power is turned on the pump continues. The wash cycle icon flashes, but the usual cycle indicator is not lit at all. The dishwasher will not commence a new cycle.


... Asko D3122XLW / D3122XLB Dishwasher

Kenmore 17373 dihwasher overfills on prewash cycle only. I can turn off the water supply on the prewash, wait for the cycle to complete and drain. Then turn the water back on, and it runs fine for the rest of the cycles.


It is posible to have a presostat(presure gauge) for prewash and this is damaged(bloked) and another for wash, this may be positioned on a main board or in another place. i don't thick you wil fix this problem whit out the qualified personel. also ca ... Kenmore 24 in. 17372 / 17374 / 17379 Built-in Dishwasher

My Quiet Power 2 dishwasher does not let water go into the cycle and then it turns itself off. Is there a setting that needs to be turned on--or how do I reset the cycle so water goes into the various cycles.


Check to make sure the drain pipe of the D/W output drain water is higher than at least half way up the tub of the D/w. Just below the top point of the sink drain is best. ... Dishwashers

Asko D1706 Dishwasher will no longer respond to control knob, turning knob clockwise has no effect on cycle nor will this turn dishwasher off! Dishwasher appears to be stuck in some part of cycle but will no longer wash dishes, door must be left open or will not turn off!


I also had this problem.\015\012Support person couldn't tell me if the pump was supposed to run even when setting the control knob to 'off' (bar before (1)).\015\012After draining the pan, the control knob functioned normally. So apparently any power ... Asko D1706 Built-in Dishwasher

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

Haier hdw101wh.The dishwasher starts when you turn the dial the pump discharges waterto the outlet it clicks to next cycle but remains washing will not cycle through the wash cycle it keeps on washing . You have to turn it manually to get it finished any info will be appreciated.


... Haier Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1053 seconds