Having problems with your Westinghouse Dishwashers ?
Westinghouse virtuoso 922 showing FL in control panel
Repair Help & Product Troubleshooting for Westinghouse Dishwashers
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Westinghouse virtuoso 922 showing FL in control panel
... Westinghouse Dishwashers
When I try to start the dishwasher, I can get the light to show I want it do do a normal load. Then when I hit the start button, it lights up but the machine will not sstart. Then in a few minutes the lights on the control panel at the top of the door go out. What can I do to fix this? The model # is KUDS011JBS0 tHE 0'S HAVE A SLASH ACROSS THEM THE TYPE IS 577-0 SUPERBA
Hi,\015\012\015\012Your control board has gone bad... you will need to replace it.\015\012The replacement is not very hard, just make sure that you mark where all of the wires go before removing them.\015\012\015\012Here ... KitchenAid Dishwashers
PLD2560LCC1 Frigidaire Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.
... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher
Pld2560lcc1 Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.
Pulled the touch pad, go after the middle third with a very small screw driver, cleaned the flex circut with contact cleaner\015\012\015\012powered up fine seems to be working again ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher
Miele Optima Series 2470 Dishwasher sounds a beeping sound and flashes a F19 error on the control panel. Last week the beeping sounded and flashed a F13 error on the control panel. I looked in the manual and it said to clean the filter, which I did and put it back in place and locked it. Now the beeps sound and it is now showing a F19 error on the control panel. Help!!
FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.
Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher
The control panel does not function and therefore the dishwasher shows no power and therefore does not function at all. Can I replace the parts to the control panel myself?
... Maytag MDBH965AWS Stainless Steel Built-in Dishwasher
Our 2 door virtuoso has developed a problem where the control panel on the freezer door lights up and then beeps. Sometimes it beeps every 30 secs. It's driving us nuts. We have asked a couple of
... Westinghouse Servis & White Fridge Thermostat Hy260
An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C
1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher
Control panel showing count down number "999,888, 777, 666, ...."
You somehow got it in TEST/Maintenance mode. I think if you PRESS and HOLD Start for 15sec, it will go back to normal. If not, pull the plug and let sit for 1/2hrCheers! ... GE PDW9200N Built-in Dishwasher
Our Westinghouse dishwasher stopped working at the start of a heavy wash cycle. The light inside is working but the control panel is not. There is no indication of any power on the control panel.Your assistance will be welcomed
If there is no power to the control panel it must be a failure of the power supply in the unit.\015\012First of all ensure that the mains supply comes into the control panel from the power plug to the unit. \015\012The program controller ... Westinghouse Dishwashers
Gld2440req1 No power in control panel, some times shows PF, we clear and try to start a cycle, dishwaser stops and panel loses power
... Frigidaire Dishwashers
Model #PLD4555RFC0 The control panel lights on the front are all flashing and start cancel button will not change anything. flashing Er with wash, dry, clean, and and S showing. Top controls have China/Crystal light flashing and Low rinse agent light flashing. Nothing seems to work
... Frigidaire Dishwashers
Dishwasher problem Hi We have a Whirlpool GU 2300, the machine has stopped and is the clean LED on the control panel is showing a 7 pulse sequence which I guess is a fault alarm. I have tried resetting, checked the door switch and looked at the pressure sensor at the drain pump outlet. I changed the heating element and fitted an uprated control card earlier this year. Any ideas?
I solved the reset by pressing the air dry and reset buttons 6 times in sequence, the whole panel array lit and I was then able to reset. I have had no problems since and have used it 6 times. I initially thought that the chipset had a volatile memor ... Dishwashers
Kenmore model 665, cleaned around control panel with a brush and now only left side will flash now showing quick rinse flashing only and is locked can't change and seems as if right side of panel will not do anything
Not running at all. replaced control panel and still wont run, but panel lights up with only - - - show up. checked door switch and current is running through it.
Is the model number the 15173 Kenmore? The stainless steel version? Please let me know and I will keep checking here on the solution. ... Kenmore 24 in. 15173 Stainless Steel Built-in Dishwasher
F1 shows on control panel of both drawers,after a couple of startup.Even when machine is not being used both drawers startup on F1,only way to control is to shut off at main supply
Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You’ll need to reset it by poweri ... Fisher and Paykel DD605SS Stainless Steel Dishwasher
Kenwood dishwasher KDW60X10 showing error E1 on control panel.
... Kenwood Dishwashers
Got a secondhand Westinghouse SB920WE Dishwasher but the lettering has rubbed off the control panel... I was hoping for a user manual...
Asko D1796 control panel will not reset....it is showing 5 on it
Shut power off at breaker, look under washer there is a pan, if any water is in that pan, there is your problem, remove the water with a towel, plug washer back in ... Asko D1796FI Built-in Dishwasher
Thor dishwasher Model No. D3764FS purchased in 2004, can't find users manual and have a problem ... A red light is showing up on the control panel just above a symbol that looks like a element ???? Have tried on the internet for user manual but had no sucess... Are you able to help me... thank so much
Fisher Paykel control panel to far left side has a film on it that chipped off - showing a shinner stainless steal under it. I guess this is a coating of some sort. Dish draws are 4 1/2 yrs old. Mild det on them only. Only bottom draw has the cracking on it. -- can that be fixed or just has to stay ugly.
You can buys the parts that look chipped/ broken and replace them. Panel parts are very easy to replace.\015\012\015\012Check out which parts you need from the parts manual and order from the local fisher and paykel distributor.\015 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
The control panel on my dishwasher is showing a tap and E15
E15 means that unit doesn't think it's getting water. Make sure the water to the unit under your sink is turned on and the dishwasher is getting water. If so then start a cycle and wait until the error occurs. If there is not water inside the t ... Bosch 24 in. SHU43 Built-in Dishwasher
We had a problem with our garbage disposal and it resulted with water leaking from our dishwasher. The disposal is fixed, I removed the excess water from the dishwasher. I tried to run the dishwasher empty to clean it. It runs but then the E-2 alert shows on the control panel meaning high water level. I read in the book that I may have to have a service person do some sort of a reset. Is this correct?
Contacted the company and they e-mailed instructions to fix problem ... Asko 24 in. 1895 Built-in Dishwasher
Hi, I have missed place my manuel for my dishwasher. It is a single-draw stainless steel, model DS603. The problem I have is F1 is showing on the control panel and it has a beeping sound. How do I rectify this problem? Cheers
F1 means that your dishwashers have flooded. You can \015\012download the video in the link below to see how to get rid of the error and fix your dish drawer for numerous other problems.\015\012 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher