Having problems with your Whirlpool 24 in. ADP5962 Free-standing Dishwasher ?

Drainage I have a bosch slimline[13HIB], I have found stagnant water in it.All I have done so far is bail it out and then try and see if there is a blockage in the waste hose by detatching it from the waste pipe and running water back through it. There was no debris in the filters that sit at the base of the machine.Should I run a quick wash or is there a chance that it will fill with water and I'll flood the kitchen?


Answers :

Have you checked your drain hose? If it's not looped above the point that it enters the sink drain water will back flow from the sink to the dishwasher.
This normally shows blockage in hose , assuming you have checked and cleaned filter.Glass sherd was the problem with mine , first time then second was block outlet hose cause by backup of garb.Glass was in system at least 4 months before it moved in outlet hose and stopped full drainage.
Repair Help & Product Troubleshooting for Whirlpool 24 in. ADP5962 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Drainage I have a bosch slimline[13HIB], I have found stagnant water in it.All I have done so far is bail it out and then try and see if there is a blockage in the waste hose by detatching it from the waste pipe and running water back through it. There was no debris in the filters that sit at the base of the machine.Should I run a quick wash or is there a chance that it will fill with water and I'll flood the kitchen?


Have you checked your drain hose? If it's not looped above the point that it enters the sink drain water will back flow from the sink to the dishwasher. ... Whirlpool 24 in. ADP5962 Free-standing Dishwasher

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher

Hi, I have a Fisher Paykel DD603I (integrated) dishdrawer unit. The bottom drawer soap dispenser has water in it after it runs (and leftover soap), and there is a small amount of water sitting in the bottom of the drawer. The dishes don't get totally clean. I have removed and cleaned the spray arm, drain filter, filter plate and bottom of tub. Found nothing clogged or particularly dirty. Put all the parts back in and everything moves freely. Ran it empty, and same problem occurred.


Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doe ... Fisher and Paykel Dishwashers

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

DW fills up with water after sitting. When I turn off the water supply it does not fill up. Removed solenoid valve and cleaned the filter and check for possible blockage. Put back together and turned on water supply. did not fill up until we used it for the first time after my fix. Could the solenoid valve not be sealing off completly DW is a Bosch SH5316UC/U12


... Bosch Dishwashers

Dishwasher not draining E25 error code (Bosch exxcel) . I have cleaned filters & removed pump inspection cover to check / clean debris I have also checked the waste water pipe is not kinked, it runs for 1hr 15 mins last time and then cut out with the error code displayed.


Gr8 stuff klaudi & Nypmh - rocking it back 45% worked a treat. Bloody BonzaShell XX ... Bosch Dishwashers

Hi I have Bosch SKT 51 tabletop dishwasher, all has been well, came back to it one day and the cycle had stopped (its a dial). If i hold the power button in it still works. Any suggestions please. I have checked the Water feed in and the filter is not blocked, neither is the waste pipe


Hi.The problem is likely the switch itself. the switch should be part of the control pad, which I think is a single spare. A test on the switch can be done by reading impedance on the control pad wiring harness while operating the switch. ... Bosch 22 in. SKT5102 Free-Standing Dishwasher

Water sits in the filter area and tends to smell after a few days is this normal water to sit in the filter area?


... Whirlpool WDT910SAYM Gold Dishwasher

I have a Miele G892 SC dishwasher. When I start the cycle, it drains (except for a bit of water left below the triple filter). After that, the intake valve opens and water enters. It then does nothing for a period of time until the "intake/drain" indicator light starts flashing. When I open the unit, I find about 1/2in of water in the tub (above the tripe filter). I have 1. cleaned the intake valve filter (no blockage found) 2. Inspected the drain line at the base of the unit as well as t


The pump is running due to the float switch or the float itself either being stuck open or broken and showing a fault this is why you have water going in to a certain point but not the point required for washing the dishes and then due to the float s ... Miele Dishwashers

Smeg e2 error (water level tripped). Filter is clean and no rubbish below filter on inside of dishwasher. I have taken the front panel off but am not sure where the float device is located - I am wondering if it is just to the left of what looks like a solenoid. There is no water in the base of the unit in the front panel so would rule out any leaks. Reset program and turned off power at socket but still not using hot water. Possible PCB issue ? Any advice appreciated. Smeg DI612C Dishwasher.


... Dishwashers

I ran a load of laundry in whirlpoo[ duet ht, model ghw9400pl4, error code p-09 was indicated. water was overflowing from door, and water was continuing to fill the tub. I turned off the faucets, unplugged & restarted in drain mode it hummed but would not drain. I turned the faucets back on and retried to drain but it would only hum. I manually removed the water by losening pump filter. There was no debree in filter except for a little bit of hair. The pump & vain was free & clean, and I co


It is your mixer value that is malfunctioning. ... Whirlpool Dishwashers

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

I have a LG Dishwasher LD 14AW3 it fills and runs for about 30 min. It then appears that when it tries to rinse it cannot get water and flashes "1E". I disconnected the unit and when I moved it out of its position water was leaking from the bottom of the unit. after cleaning out the inside filter & the hard water filter I re-connected and found it worked. I ran a dishwasher cleaner through it at high temp. After a few loads the problem has come back. It is now located in MY garage waiting for me


Found a leaking component that was causing the foam float located and attached to the inlet valve to shut down the water inlet and the water inlet Solenoid was also sticking. I found out this simply by tapping it while it was trying to get water for ... LG Dishwashers

Kleenmaid DW8 top washer does not operate. Apparent blockage in the water supply tube which runs up from the bottom water supply. How do I remove the bottom assembly comprising the main filter, waste trap and micro filter? I appears that these must be removed to access the water supply tube mentioned above.


... Dishwashers

Hi I have a Meile G 685SC Dishwasher. It has a water inlet problem. It will not fill and just keeps cycling through the water filling process with the water inlet light flashing. I have taken off the inlet pipe and removed and cleaned the inlet filter and washer and put them back. The filter was blocked with a sand like substance. I have taken apart the antiflood valve also attached to the inlet pipe but it is gel sealed so unserviceable. The inlet pipe itself on removing from the vlave appears


Check that the stopcock is opened fully or whether the water inlet hose\015\012is kinked...Check that the water inlet filter is not clogged and clean\015\012it, if necessary, as described in the operating instructions....Check\015\012that the drain p ... Miele 24 in. Incognito G643SCVI Built-in Dishwasher

2 weeks ago, I had a plumber come and put in a new garbage diposer and since then somewhat old/dirty water seems to be sitting at the bottom after all cycles are done. I calle dhim back and he says that there is no problem in the plumbing but more with the pump. I even use the wt/dry vac and removed water and ran it but still comes back with water at the bottom. also the dishes smell like soap. Help!!!


The plumber did not make an air gap in the dishwasher drain hose when he reattached it to the new disposal. Look under your sink, does the hose (attached to the disposal) go down and through the cabinet? If so, that is definitely the issue. Simple ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Water drainage I have followed the manual instructions for clearing all appropriate filters on the intake and outflow side but the cycle does not complete and leaves a pool of water in the base. What next? I have the G568/858 Plus Incognito unit (thisis the closest part # to my actual unit--can't even find teh right # listed...), and aI m dealing with the sme issue. I have followed all of the recommended steps in cleaning the filters, traps, etc. There are no kinked hoses. The water drains to b


YOU NEED TO REMOVE THE LOWER SPRAY ARM AND REMOVE THE SHELL THAT IS COVERING THE PUMP AND FOOD SHREDDER ,HERE IS WHERE YOU LOOK FOR A CLOG. ... Miele 24 in. G892SCU Plus Built-in Dishwasher

At the end of the cycle the water is not draining out of the tub. I vac'ed out the water, removed the filters and checked for debris but found non.


Check drain hose first.If you do not find any blockage, then you will need to access the pump, remove pump hose and look for blockage in there.If there is no blockage at all, then either the water level switch, a faulty pump ( ... Bosch SHV46C03 Built-in Dishwasher

Hi there, The error code 'strong and economy light flicker fleetly' is showing. the manual says that this means too much inlet water. We have drained the machine, cleaned waste pipe and tried to operate with a reduced flow from the inlet pipe but it's still not working. I filled the base of the dishwasher with water to see if it drains properly. It seems to be draining, but also leaking out of the base as well..? Any ideas?.


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Baumatic Dishwashers

Machine just started leaving dirty water in bottom of machine. cleaned filters,had machine apart,removed and cleaned waste pipe. pump runs and impeller feels ok.only time i could get any water to drain into bucket was when shook waste pipe very hard?


Check that the pump is clean and not loose. Make sure pump, impeller, and waste pipe are in alignment with each other and are clean. If it works when you shake the pipe, then there is still a clog inside or the pipes aren't aligned correctly and some ... Dishwashers

Does not get my dishes clean, leaving a film on my glasses, not getting food off. tried to take apart to clean but could not figure out how to get bottom filter out with the large water bracket going up the back of the dishwasher to the top water bar. I bought as a store model, no instruction booklet. How do I clean out bottom filter?


The problem is hard water. www.dishwasherfilter.com has a product to solve this problem once and for all. It filters the water going into your dishwasher and removes the ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

The water is not draining from the bottom of the dishwasher. i have removed the filter and there is not much debris in the filter. there is however are pool of still water. what to do next?


May be float switch problem , try rocking the machine with power off, and try again,pete ... Jenn-Air 24 in. JDB1090AWS Stainless Steel Built-in Dishwasher

I have a whirpool Quiet Partner III, and the top layer of glasses is not getting clean. I had a technichian out some time ago, and the problrem was caused by food debris trppaed in the filter in the wash module. He saud it was easy to clean that out, so I have removed the lower spray arm, but cannot undo the 4th screw that will allow me to take the grey round filter cover off to remove the food or paper debris. It is under the white flat pipe that delivers water to the wash module, and I cannot


I had same problem, would not clean well and fixed it. . I cracked open the door during wash cycle and used screwdriver to defeat the door lockout. The water from the bottom sprayer was only shooting half way to the top of dishwasher. To fix I remove ... Whirlpool Dishwashers

Water Leak My dishwasher is an Ariston Advantage AF250: I have been told that internally its the same as a Hotpoint DF55. It intermittently leaks water onto the floor from the front at its base during use. At one time it ruined the motor which I had rewound and at the same time I made a new polystyrene float for the base pan overflow switch. All was well for months, but now its leaking again. I have blown through the tubes from the drain filter well to the pressure sensitive switch, but all


Hi there, dishwasher leaking might be due to either of these causes, check these:Main tub sealNote… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dishwasher, the foll ... Hotpoint 24 in. DF55 Free-standing Dishwasher

Our Kenmore dishwasher 665.1726 doesnt seem to be cleaning as well. LAst time this happened a serviceperson cleaned out a filter where food debris had clogged the water flow. We were able to take off the bottom wash arm but couldn't figure out how to get the filter off (there are 4 screws holding it in place and one is under the plastic arm that caries water to the sprayer.


I had the same problem!\015\012\015\012The arm WILL come off....you have to pull the screen off. ... Kenmore 24 in. 15689 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1625 seconds