Having problems with your Whirlpool 24 in. ADP5962 Free-standing Dishwasher ?

Machine starts to pump out then goes to f4 after 4 minutes

\015 Starting up then goes to f4\015

Answers :

Waste pump fault or blocked pipe
Repair Help & Product Troubleshooting for Whirlpool 24 in. ADP5962 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Machine starts to pump out then goes to f4 after 4 minutes


Waste pump fault or blocked pipe ... Whirlpool 24 in. ADP5962 Free-standing Dishwasher

My pressure washer starts fine, shoots water OK. After running for 5-10 minutes cleaning siding I shut off machine. I go to start it again within a minute or two and the thing feels like it's just about seized. If i wait until the motor is completely cool, it will pull start freely and start right up. I think something is wrong with the pump, not the engine.


Your pressure washer may not have an ez-start valve installed from the factory. Without the ezstart valve, you will need to hold the trigger on the wand open to release the pressure to easily start your engine. This link will show you wh ... Briggs & Stratton Pressure Washers

The start/pause button beeps when pressed to start a program and the machine gives a beep in response and appears to start its initial sump emptying phase but stops within 1-2 secs. Have checked pump and found no problem but start time is so short that in cannot have sensed a problem in the pumping circuit. If I persist in holding the start/pause button in, it can be released after the initial sump emptying phase (2-3 mins) and phase 1 of the wash program goes to completion. At the end of the


Hi\015\012\015\012Ronald...the beep sound itself indicates an issue with the\015\012membrane switch (control panel) and it should be replaced. I believe that the\015\012pump and motor is fine as its just beeping and doing nothing else. Ho ... Smeg 24 in. DWI612 Built-in Dishwasher

Some guys at the church was using this haracher 4000 psi, I was call and was told the machine stop working and would not crank up.I use a next machine to finish the charity jobs on saturday. Sunday the machine starts up but when I connect the garden hose and turn on the water it did not comes out, where the VALVE HOSE THAT GOES TO THE WAND ABOVE THE UPLOADER, I open every bolt and water comes out except the wand valve, pump was plush out and sprayed out, so we know that water enter the pump


Where the hoses attach to in the pump is a valve along with another valve inside of it. Remove both valves and clean and relube with Vaseline or equivalent. The inner valve will be the toughest one to remove and that its why it does not work if stuc ... Karcher Pressure Washers

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW


... Dishwashers

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle


... Bosch 607335 Water Valve Assembly For Dishwasher

Hi I have an F&P DW691 dishwasher (manufactured by whirlpool) the reser light is permanently giving two quick sucessive flashes and will not start the machine unless held on for 6 seconds, the machine then starts for a minute then stops and goes back to the two flash reset problem. Does any one know the fault code applications for this model.thanks Mike


Hi, I've got the same dishwasher but with a different fault, there's power down the cable to the d/w but no power lights on the front panel?Thanks. ... Fisher and Paykel Dishwashers

Have a Miele G1220SC dishwasher. It recently developed a strange problem: when switching it on ALL program lights come on and the machine starts taking water. after a while it stops taking water and starts to pump water, all the time all program indicators remain on. if you leave it on a while ( about 4 or 5 minutes) it is impossible to switch off the machine with the main switch, all you can do to stop it is unplug it. anyone experienced something like this and have any idea what part is malfun


Follow this steps and fix it. God bless you\012 \012 Heating Element\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Miele Dishwashers

Cycle counter goes to 1, but continues to agitate, does not pump the water out, nor does it go to zero. The counter will stay on 1 indefinetly, if I use the pump button, there is soap residue in the bottom of the machine. I called the Sears repairman, he was here about 10 minutes, unplugged the machine from the wall and said that probably I had a power surge and that would solve my problem. It did not. I live in a very small town, I will have to take my dishwasher to Las Cruces (101 miles awa


Hello, welcome to Fixya.\015\012\015\012I`ll start by saying how unfortunate it is to have too many so called "pro`s" trying to diagnose appliances who have no business doing so if that is how the repair-person you spoke of e ... Bosch Dishwashers

At start up the machine goes directly to CLEAN after about 2 minutes


I have a Bosch SHE4AM12UC, it keeps going from active to clean. I tried everything. I even tried some of the things listed here... then i was looking and seen where someone said about the latch on top to make sure it wasn't bent or something... well ... Bosch Dishwashers

Hi I have a LG LD-2052 dishwasher. It gives me an E 0 error - the water does not pump out when I open the machine after a few minutes when started to wash and message of E 0 appears? Have cleaned an


... LG Dishwashers

We have a Bosch Model SKT5102GB/07 and the problem is as follows; we load the dirty washing and start the washing process, the machine then goes through the full cycle of wash. Once finished you open the door and notice that the washing is still dirty and a large pool of water is laying in the bottom of the machine. We have had an independent engineer look at the machine and he has advised that the pump needs changing. Look forward to your reply, thank you. Regards Michael Ballard.


Replacement parts are available here\015\012http://www.repairclinic.com/SmartSearch/SmartSearch.aspx\015\012\015\012on the narrow ... Bosch Dishwashers

After starting dishwasher to do a normal wash with heated dry, the dishwasher stops and Clean light blinks 7 times, pauses and this continues until I reset the machine. After reset it goes to rinse only and goes for a minute or so and stops.


Hi\015\012\015\012Please check if the clean light is blinking 7 times. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To reso ... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

Dishwasher seems to start up as it should then after a few minutes it stops water is going in and pumping away it just doesn't seem to be pumping around the machine eco light is flashing


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

The dishwasher starts and water gies into the machine but after a couple of minutes it stops. Then a minute or so later it pumps out the water and beeps to show its finished. It does the same thing on all programmes. Any help much appreciated. BC.


What brand have you got? It could be the main spray motor because when the appliance has finished filling it should automaically start the water pumping around. ... Dishwashers

Hi there,i have a brand new but 3 year old,diplomat 8332,just fitted it,it does the pre was ok,pumps out the water,goes to next stage,you can hear water entering the machine,shortly after it has started the main wash,it starts to cut out intermittantly,then F2 code appears,and a bleep.i have taken the lower panel off and checked for leaks and to see if the valve was free,all ok,also relay click in front panel,safety cut out ? any ideas please.


... Dishwashers

Kenmore model 665.15829 Air dry lock button light is on. Washer won't start. tried different codes to reset. no luck. when I pushpots pans button and start it goes into sensor mode and tries to pump out. after one minute operation it stops. The tub is dry no water in unit.


I have reviewed your problem and have the fallowing for you to aces.\015\012First, believe it or not, in some cases, when you get a power urge the unit will lock out and continue until a full reset is completed.\015\012Try di ... Dishwashers

Hi, When I turn on my dishwasher, it fills as normal with water but is not pumping into the upper spray arm. the spray arms are not clogged, I have checked them. Anyway, I always rinse the dishes under the tap before placing them in the dishwasher. I have to switch the machine on/off several times then the pump starts at full force.Occasionally it goes through a complete cycle without havig to switch on/off. It's a Siemens Lady model, E-NR SN53300GB/08, FD 7201 058479. The dishwasher is used


... Dishwashers

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

Have a Kenmore dishwasher #665.1677993, approx. 13 years old. Upon starting new cycle the pump turns on for a few short seconds, then off, then after a couple minutes it goes on again for a few seconds then off, then later in the cycle it does stay on for a longer period of time. In conjuntion with this intermitent problem it has begun leaking out the bottom of the front door. I have checked drain line, check valve, strainer/screen and vent in the door. I assume it is an electrical issue?


... Kenmore Dishwashers

Dishwasher- three years old, wont wash. the pump starts making a straining sound after a few minutes in any cycle, and then I get the E1 code. the machine does not shut down. Tom


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Error E1 is a leakage error\015\012which occurs due to excessive RPM of washing motor during wash cycle due to\ ... LG 24 in. LD-12BW5 Free-standing Dishwasher

My dishlex dishwasher starts then every 2 minutes flashes 10 after restarting i have cleaned out discharge tube and pump no difference what could it be it does wash after awhile then goes back to beeping and flashing 10 water pressure all ok


... Electrolux Dishwashers

Hi - I have a Neff S5456X2GB/13 and it has decided to wash cold and doesn't dry. When washing in auto mode it seems to take forever but does eventually stop, and I've noticed that when opened the time to go indicator can vary quite a lot (sometime goes backwards in that if you wait ten minutes and look again, it's saying it's going to take longer than it did before) I have replaced the pump in the past so I know how to dismantle the machine. What are the possible causes of this problem and ho


Ok, really you have maybe three problems, that to me seem interconnected.\015\012\015\012First, IF connected up to the Hot water source, then either that has failed or the Inlet Solenoid has.\015\012\015\012Second, the heating element has ... Neff Dishwashers

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1403 seconds