Having problems with your Whirlpool 24 in. ADP5966 Free-standing Dishwasher ?

My whirlpool dishwasher is flashing 8 times - I pressed and held the start button to reset and then pressed start again, it kicked in and started to fill with water and stopped again - any ideas.


Answers :

Hello, I have a Whirlpool DWF A10. The machine starts then stops after a short while and the indecator light flashes 7 times. What does this mean? Any body come across this?
Some times the Tech sheet for the machine is located on the back side of the kick plate.
\015\012
\015\012This sheet sometimes will give you the blinking error codes. as log as someone has not removed it.
\015\012
\015\012This is the first place a tech will look for help with your machine.
Repair Help & Product Troubleshooting for Whirlpool 24 in. ADP5966 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My whirlpool dishwasher is flashing 8 times - I pressed and held the start button to reset and then pressed start again, it kicked in and started to fill with water and stopped again - any ideas.


Hello, I have a Whirlpool DWF A10. The machine starts then stops after a short while and the indecator light flashes 7 times. What does this mean? Any body come across this? ... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

I started my dishwasher this morning. It started to fill with water, then stopped. I can hear a very slight hum sound as if the motor is running. The start/reset light flashes but does not reset upon pressing the button. Any ideas for a self-help resolution?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... GE Nautilus 24" Built-in Dishwasher

My Maytag MDB5600AWB quiet series 100 dishwasher starts, fills with water and then makes three "clicking sounds", after the third click the machine stops and turns itself off. I can get the water to drain by restarting the machine and pressing start/cancel. Anyone have any ideas?


... Maytag Dishwashers

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

My aeg favorit 35085 dishwasher starts it program fill with water then stops if i drain the water out and restart the program it starts again fills with water then stops any ideas


... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

I have the Kitchen aid KUDS01DL dishwasher. It was working fine until last week. When starting a cycle, the washer fills with water. Once filled, the motor makes a humming noise and does not circulate the water. I end up stopping the cycle and the discharge pump empties the water. I took apart and cleaned the basin this morning. I did find some random garbage but it did not seem blocked. Do you have any ideas?


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Neff 4456 water resevoir not filling. Checked float switch and all OK. Checked water supply and all OK. Filled resevoir manually from top of resevoir and program cycle starts but stops when rinse is required.Have stripped down and cleaned switch with float switches as I have had that problem before getting clogged. Any ideas


... Neff 24 in. S4456 Built-in Dishwasher

Triton dishwasher (GSD5110) won't fill with water. Unit is getting power and pressing start opens the soap dispenser, but water doesn't fill. Any ideas?


... GE 24 in. GSD5110 Built-in Dishwasher

So, it was working fine for 4 years. Then last week it started getting louder after the initial fill cycle. Now, all it does is fill the bottom with water, clicks (where the motor used to kick in), then just hums. Nothing happens, but when I hit the cancel button, it empties the water from the bottom. Any ideas?


Your spray pump motor has become blocked or ceased - do you have the tools and skill to dis-assemble the machine? ... Whirlpool GU2455XTS Built-in Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Asko d3100 dishwasher still giving problems after replacing inlet valve. When you press the start button all of the lights come on and there is some pumping sound with a dribble of water coming through from the right hand side. When you take your finger off the start button everything stops, no lights, no pumping. Anyone got any ideas?


Hi.To start, disconnect power and ensure that there is no water in the tub when you restart the dishwasher.It looks like the overfill switch is preventing the machine from filling. The overfill (water level) switch is either a ... Dishwashers

Our dishlex global 310 will start to fill with water and then will get to the pre wash stage, then will completley stop and start flashing rinse? I have no idea whats going on please help!


This is an error code and means the wash motor has failed & needs to be replaced. ... Dishwashers

Hi, Dishwasher problem: When a programme starts, the machine fills with water then stops and the "check water" light comes on. To empty the machine, I used the reset programme which does empty the machine. Any ideas of about what might be causing and the solution to this? Many thanks, Richard


You will need to check the inlet valve and the water level pressure switch. It can also be a low pressure in the pump that is giving out the signal for the control board to shut off.\012So first of all check the water line throughly to confirm. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Kenmore dishwasher model # 587.15103800 wash cycle won't start. It fills with water and stops. A few minutes go by and it drains. Motor is working. Any ideas why the wash cycle won't start?


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Dishwasher not getting enough water in either drawer, although top drawer gets more. Dishwasher keeps beeping during cycle and reads not enough water and then stops running until you press the start button. Need Help, any ideas?


This sounds like a hard water deposit problem.Check your water inlet valve for a screen and see if its clogged. Also it may just be a water valve/solenoid problem. As in, it's too crusted up to float up and down.Some models have a water f ... Fisher and Paykel DD605FD Stainless Steel Built-in Dishwasher

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

We have a Maytag MDBH950AWS Dishwasher that won't start. When you press the start button the cycle light, washing light , heated dry, sanitize and extra rinse lights all come on the dishwasher fills with water and after a couple of minutes it shuts off. Any ideas what is wrong? Thanks


I have Miele incognito that when I shut the door it does not turn on? Not sure why it stopped working all the sudden ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

Kenmore dishwasher model # 587.15103800 wash cycle won't start. It fills with water and stops. A few minutes go by and it drains. Motor is working. Any ideas why the wash cycle won't start?


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Hobart lx-g HI there, I have a weird problem with my dishwasher... when I press the off buttom, instead of staying off... it restarts by itself. Also, when it starts filling up, water overflows from the machine ( when it filling up the temperature rises alot more then usual it reaches 190f) and then i turn off the machine to stop the flooding... can you help?


The problem with the machine restarting is with your keypad, the on button is stuck on and needs to be replaced or you can continue unplugging it. Your other problems are most likely caused by lime build up, is the inside of your machine white. I ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I have an kenmore elite "ultra wash" model 665. not sure the rest.. about 7/8 years old, making loud buzzing sound during wash cycles,starts about 5 minutes into the normal wash cycle. i removed the inlet protector and the chopper area and all was clear.clean...it's running now and seems to be pumping the water, but can live with this buzzing noise,,, any idea, is the pump on it's way out ? just stopped as it kicked into another cycle, at 42 minutes...but it will be back, any ideas ? (back alrea


Buzzing sound may be coming from a solenoid that is mounted under the dishwasher, below the tub ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1986 seconds