Having problems with your Whirlpool 24 in. DU1050SS Built-in Dishwasher ?

My Whirlpool is only a couple of years old too and it does the same thing. It stays on the wash cycle and the timer stays at 79 minutes. I have to cancel the wash to get it to stop and drain. Anyone know what is wrong with it?


Answers :

If the timer does not advance. It is most likely a timer motor.
Repair Help & Product Troubleshooting for Whirlpool 24 in. DU1050SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Whirlpool is only a couple of years old too and it does the same thing. It stays on the wash cycle and the timer stays at 79 minutes. I have to cancel the wash to get it to stop and drain. Anyone know what is wrong with it?


If the timer does not advance. It is most likely a timer motor. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

I have a SHU43C05UC/22 Bosch dishwasher that runs fine till it gets to wash then it seems to stick there. the timer times down to 1 and it stays there for a really long time. it doesn't appear that the washer ever gets out of the wash cycle. when you stop/open the door there is still soapy water in the tub. You can cancel the program and it will drain the tub fine then you have to select rinse and hold to clean out the soap out.


... Bosch 24 in. SHU43 Built-in Dishwasher

My Bosch SHE45M built-in dishwasher is suddenly taking an extra-long time to go through its cycles. On Regular wash it will countdown from 117 minutes to 31 minutes. When it hits that time it resets to 87 minutes, then counts down to 1 minute and will not stop. I have to hit the cancel-reset buttons for it to drain. I have tried to do a hard reset by cutting the power at the breaker for 20 minutes or more. I'm interested in potential parts and a description of how to fit it! Thanks in advance.


... Bosch SHE45M06UC Built-in Dishwasher

My Bosh dishwasher now runs well past the 105 minutes as stated in the manual, over three hours before I intervene. It gets stuck on the wash mode, it wont drain or rinse, just runs and runs in the wash mode (I know it's in the wash mode because when I open it up, theres suds inside). It will do the wash mode until I reset the wash mode to "Rinse & Hold". I appreciate whatever information you could provide.


Hello, welcome to Fixya.\015\012\015\012The problem you're describing is unfortunately a common one with B/S/H/ built dishwasher's. That includes Bosch, Thermador, Siemens, and Gaggenau. ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

I have a kitchenaid dishwasher model kuds24se with a problem. I MUST hit cancel before I hit start. Note that it doesn't matter how long it's been since the last cycle. It could be a few minutes or a day or more. I have to hit start to get a complete wash cycle. If I don't hit cancel, the washer goes through some sort of cycle and stops. It seems like a normal cycle but of course it is not because I don't hear any water and, upon completion, when I open the door there is heat but the soap dispen


... KitchenAid KUDS24SE Built-in Dishwasher

My dishwasher is not draining unless I hit the cancel drain buttons. I also noticed that when time gets down to 1 minute it stays there and keeps running


Most likely it is not completely level. This will stop the cycle every time. The drain/cancel just overrides the sensor, but you need to level it up completely, this should solve the problem ... Dishwashers

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Both spray arms of my DU943PWKQ0 do not turn or spray. The motor is moving and the it drains without problem. During the wash and rinse cycle I can hear the sound of water, however it doesn't clean at all and the sprays arms stay where they were. It seems the motor only creates no spray, but wave. I powered cycled the dishwasher, the problem remains the same. Anyone know what's wrong with it? Thanks James


Try rotating the spray arms by hand. It should rotate freely. If possible clean the arm rotating place by removing them.Arms rotate by by pump pressure only. finally check the water pump also. ... Whirlpool DU943PWK - Multiple Color Built-in Dishwasher

The door wont stay shut on frigidaire 4300. I have cleaned all around including gasket. Halfway through the wash cycle, cycle stops and we get CL code for open door. If we push on door, it goes for another few minutes.


Something is wrong with the door latch. Replace or make adjustment. ... Frigidaire Dishwashers

Kenmore 17369 When cycle starts... it sounds terrible (crackly sounding).... doesn't sound like the water is coming into the dishwasher. If I add water to the machine during a rinse cycle...it will wash and drain on its own.... Then I hit cancel. Please help.. I can't locate the owners manual.. Do you know where I can get one.. I understand that you can open the bottom up and see if there is anything lodged in the bottom of the dishwasher. Please help! thanks Cheryl


The problem is your water inlet valve. If you remove the panel at the bottom of the dishwasher you will see\015\012either a copper hard pipe, or a flexible steel hose leading into the\015\012water inlet valve.BE SURE TO CUT OF ... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

The detergent dispenser [Main Wash] door doesn't stay closed. It seems like there is something wrong with the latch, but we can't what. We've cleaned it, but don't know what else to try. There don't seem to be pieces missing or broken. But no matter what, when we put in the detergent [we use the cubes] the door always just pops open and the detergent ends up falling to the bottom on the dishwasher. The dishes are still getting relatively clean, but we want to solve the problem with the door


... Frigidaire FDB1200RG 24 in. Built-in Dishwasher

I got the pressure washer started - lots of smoke etc after not having used 3 years. I then poured in wrong oil to top it off - my brother's chain saw bar oil. DARN. After 3-4 minutes it started rattling and stopped. Can't pull the chord to get started. Did it seize the engine? I have drained all oil. Can I try using a cleaner, light weight oil to try to unlock it?


Nope! you have blown the seals and most likely the cylinder is full of water. You will need to take it to the repairer to have it cleaned checked and new seals fitted. $200 ... Karcher 1750 psi Electric Pressure Washer

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have an SHU 4322. It displays "2H" in the countdown window. It will drain-cancel properly, but all of the programs display "2H" instead of the normal # of minutes for each cycle. How do I get the wash cycle to start normally?


Just reset the unit by unplugging the cord from the wall for 4 hours. The purposed for this is to drained the current stored in memory IC . So it will works normal again. Plug it again after 4 hours to see the result..Good luck: ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher hums I have a 2003 Kenmore Elite Ultra Wash Dishwasher model #665.17469300. I started the wash today. The water came in the unit and started washing then I heard it stop and it just started making a humming noise. I was afraid it was going to overheat or something so I cancelled the washed and it drained out. I started the unit up on a different cycle and the water came in the unit but did not wash it just hummed so I cancelled and drained it again. I did that on all cycles and the sa


... Kenmore Dishwashers

Gaggenau GM 915-710 UC6 dishwasher will not fill and wash. Close the door, turn lever. Empties water from sump. (drain hose was not clamped above disposal outlet nipple, fixed that) Machine empties sump, but will not stop after sump is dry. Will not initiate fill and wash. Manually stop machine. Can't get control board to do the diagnostic to get an F #. Pressing button 1 and 3 at the same time. A couple of the plastic tabs on the circuit boards plastic support housing that link the


... Gaggenau GI936-760 Dishwasher

My bosch excell dishwasher won't drain it stops during the wash and won't restart until I have emptied the water then it will wash ok until it gets to the drain part of the programme then it stops again. The red warning light comes on for check the water


A clog in the drain line or air gap (if there is one) is the usual\015\012reason that a dishwasher won't drain. Often the problem is at the point\015\012where the drain line attaches to the garbage disposer or household\015\012drain line. If you remo ... Bosch Dishwashers

Kenmore dishwasher 665.17534202. something is wrong with either the timer or the motor. On a normal cycle it starts at 78 minutes and gets down to 48 minutes and it stays stuck at 48 minutes for appro


Http://www.allrepairmanuals.com/kenmore-dishwasher.htm?model_number=+665.17534202 ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1954 seconds