Having problems with your Whirlpool 24 in. DU1055XTP Built-in Dishwasher ?

I have a Whirlpool DU1055XTV08 Will not start

\015 No indicator light. Will not turn on\015

Answers :

Repair Help & Product Troubleshooting for Whirlpool 24 in. DU1055XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Whirlpool DU1055XTV08 Will not start


... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

I have the Whirlpool Quiet Partner 1 the wash cycle starts and about 20 Min.'s into it the clean light starts flashing or the the start light, one or the other each time and it wont dry the dish's anymore we have already replaced the panel once and it has always popped when it is filling with water or changing cycles. HELP!!!! I hate washing dish's and I am beginning to hate all Whirlpool Appliances.


If the clean light blinks 7 times thats you heating circuit. Test the heater with an ohm meeting to see if it has open. If so order the heater kit and it comes with the control board. ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Whirlpool model GU2400 Whirlpool Gold dishwasher and it will not start. There are no flashing lights just dashes across the time remaining box. I tried to push hi temp wash/heated dry 3x but it only allows me to hit it twice and displays 88 in the time remaining box. Then it says d3 in the time remaining box. It will then start running a drying cycle for 12 minutes. If I push cancel it won't do anything. I have to hold in cancel for about 30 seconds and it will drop down to 6 minut


... Whirlpool GU2400XTP Built-in Dishwasher

Whirlpool dishwasher whirlpool ADG7440 dishwasher is starting then after about 5 mins it stops and the start button is flashing 2 times then pausing then flashing 2 times again


Hi,\015\012\015\012I can't guarantee to solve this but we had flashingh light problem and in the end all I did was to set the dial to the wash I wanted and kept my finger on the start button for about 10 to 20 seconds and it suddenly woke up an ... Whirlpool Dishwashers

I have whirlpool diahwasher ,model DU1055XTSQ3,quiet partner -1. when i start the machine the folowings things happen: 1.the machine does not start . 2.Start /resume light starts blinking ,after few seconds ( 40-50 seconds), the pots and pans light also starts blinkng .after some time ( 1 minute ) the normal light also starts blinking .All three lights start blinking 3. I have done the following to rectify the problem from the book : alnernatively pressed heated dry and normal keys for


... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

On my whirlpool ADP962 dishwasher the start light is flashing but nothing is working. I can change the programme type (ie rinse, wash etc) but the programme will not start. I can't select either half load or a time delay. By holding the start button it will start the pump but when this stops it goes back to a flashing start light. The programme progress lights are not lit. What is this telling me and how can I reset it?


... Whirlpool Dishwashers

My sound conditioned Whirlpool dishwasher is real old. It fills up completely with water. It looks like it will overflow, so I stop it. I thought it always started washing from the start. Do they always fill completely up with water, then start washing. I never noticed. I am afraid the water will overflow. Can it? Last time I ran this, it had a real loud motor. I used to hear the motor running from the start, but now I don't, just water filling up to what looks like overflow if I let it. I baile


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

My built in Whirlpool adg 9340 washer won't start a cycle at all. It seems to start a cycle and after 1 minute it stops and it starts beeping. Also water remains on the bottom. As soon as the cycle starts it drains that water and brings new water in which stays there. It won't work for more than 1 minute....


... Dishwashers

We have the Whirlpool dishwasher ,Model: ADG6 955. used it smoothly last night but this afternoon, it just will not start up. The green 'START" button keeps flashing and the dishwasher just does not start operation. I tried to reset it by holding onto the start button for a few seconds. The dishwasher stops and nothing more. KIndly advise


... Whirlpool Dishwashers

I have whirlpool Dish washer model GU 120 ES (bought in 2001). When we start the dish washer cycle the unit starts for a minute, then the "start indicator" light flashes. As indicated in the instructions, we press the "start button" for five (5) seconds, at this time the washer clears the water out and stops. If you can assist this would be greatly appreciated. Thanks Jeff


I called the service tech.... ... Whirlpool Dishwashers

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My dishwasher, a Whirlpool ADP 931, has stopped working. Possibly because the door was opened during operation, right after it was started. There is some kind of error condition indicated through a blinking Start light, but I don't know how to analyze this. This is a quite simple model with very few buttons to press. When I turn the program knob right to start it, the only thing that happens is that the green Start lights begins to blink continuously. There is also another green light


Hello & Welcome to FixYaThis light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence:High tem ... Dishwashers

I have an ADG7550 whirlpool dishwasher. Am experiencing a fault when placing on a normal 65 degree programme it starts to fill and then defaults to pre-rinse and the start button and light flash eleven times. Can you explain what type of fault this could be ? I have had a similar problem 12 months ago when it was described as a water pressure problem which again was in the winter and wonder if this is the same. I would add that if I re-set the start button by holding it down and then re-start


... Whirlpool Dishwashers

We have a Whirlpool ADG 7560 dishwasher which has recently started playing up. When switched on for a normal wash, after a short time the machine starts to beep. If you open the door the green programme light is on the pre rinse and the start light is flashing. After starting the cycle the few times eventually it works normally. Have cleaned all the filters etc.


... Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I have a ADP 4502/5 Whirlpool Dishwasher, when I start a programme it starts normaly but after a few seconds begins to pulse with the green start light coming on and off with each pulse, anyone help?


... Whirlpool Dishwashers

Door interlock appears faulty on my whirlpool awm 321 . It wont allow program start when door closes . Needs a lot of coaxing , banging with palm of hand , knee etc .Door itself appears fine , catch looks ok , finishes and runs ok once we finaly get it started .Hve tried pressing the interlock slider in with a pencil , but cannot succeed in pushing the contacts into place and starting the program . HELP PLEASE


Only solution is to replace the interlock - it is just held in by 2 screws ... Dishwashers

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

I have a Whirlpool GU2275XTVY0 when I start the cycle on normal it will run for about 5 minutes then the power button starts flashing and wont run. It drains fine and starts fine just wont finish the cycle.


It might help if the wash arm had started moving when it shut off.\015\012\015\012Unless it is always exactly 5 minutes I would say perhaps the door switch is out of alignment. It might start ok when you engaged at time of closing door bu ... Whirlpool Gold GU2275XTV Builtin Dishwasher

Whirlpool dishwasher Will not start. the clean light keeps flashing when i push the normal and then start button it will not start.


Look behind the lower acess panel( toe kick) for the tech sheet, there is aspot cleary labeled "clean light ' blinking 7 times. ... Whirlpool GU2400XTP Built-in Dishwasher

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

I can't start any new cycles on my whirlpool adg 7960 dishwasher. Everytime I close the door the beeping starts and the cycle returns to 40 with start button flashing.


\015\012Hi,\015\012\015\012The reason for the washer not going into cycles is bad or the heating element itself is bad .I would suggest you start by checking to see if the element gets hot during operation. If no, ohm test the eleme ... Dishwashers

Whirlpool disher whirlpool dishwasher clean light blinking all the time cannot start whirlpool dishwasher


Run diagnostic by pressing Normal, heated dry, normal, heated dry, normal heated dry. a total of 3 times in 15 seconds. The dishwasher will reboot and run a test load. ... Dishwashers

My whirlpool dishwasher is flashing 8 times - I pressed and held the start button to reset and then pressed start again, it kicked in and started to fill with water and stopped again - any ideas.


Hello, I have a Whirlpool DWF A10. The machine starts then stops after a short while and the indecator light flashes 7 times. What does this mean? Any body come across this? ... Whirlpool 24 in. ADP5966 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1062 seconds