Having problems with your Whirlpool 24 in. DU1100XTP Built-in Dishwasher ?

There is power to the unit, but there is no power to the touch pad


Answers :

This could be the door switch. Its located behind the control panel. Shut off the breaker to your dishwasher and remove the screws on the inside of the door behind the panel. Locate the door switch and check.
\015\012Replace if needed. On some units there are two switches to check side by side.
Repair Help & Product Troubleshooting for Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Amana model ADB1500AWW, start/cancel touch pad does not work...power to unit...wash cycles can be selected. Could it possibly be a door switch?..touch pad or circuit board?


... Amana Dishwashers

The unit is a Maytag model MDB5601AWW which it has recently began to lose power at the touch pad. The electrical breaker has been checked to confirm normal voltage. Additional investigation suggests that the unit can be reset by (1) disconnecting the power at the breaker, (2) disconnecting and reconnecting the ribbon cable that interfaces the touchpad with the control board. However, the problem reoccurs after a few normal wash cycles.


It sounds to me then that the display board or touchpad needs replacing,you havn't said that it's not doing it's cycles.so it's not causing any washing or cycle problems.i would replace the display board. ... Dishwashers

There is power to the unit, but there is no power to the touch pad


This could be the door switch. Its located behind the control panel. Shut off the breaker to your dishwasher and remove the screws on the inside of the door behind the panel. Locate the door switch and check.\015\012Replace if needed. On some u ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have power to the unit and the door switches or working fine but nothing will work ?? i think it might be the touch pad or the circut board . can you confirm ?


... Maytag MDB8851AWS Stainless Steel 24 in Builtin Dishwasher

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


The electronic control board is most likely the issue. I would replace the pab that controls the dishwasher functions. The control board controls the cycles and the wash time selection as well as the on/off function of the dishwasher. ... Dishwashers

I have unresponsive touch pad, blinks, but the dishwasher does not come on. do I need to replace the control board? or the touch pad? it's a new machine and we have only used about 10 times since we had it. This is the second dishwasher we have purchased. Could it be there's a power serge burning out the boards? Should DW be on a GCFI outlet?


If it's new(less than a year old) it should be under manufacturers warranty. if not under warranty b4 replacing any parts try killing the breaker for a minute or two ... GE 24 in. GLD5860LSS Stainless Still Built-in Dishwasher

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


Your touchpad is likely faulty. Sometimes called a control panel. You can get parts, manual, pictures, part numbers, and more at partselect.com or repairclinic.com ... Dishwashers

After a power surge the dishwasher does not work at all. It just beeps constantly. There are no lights on the touch pad at all. The only thing that stops it from beeping is to remove the 2 pin black and white wires. I replaced the control module. Nothing changes. Do I need to replace the touch pad? What about the 3 digit clock? These parts together cost 145 dollars. I do not want to buy these parts and put them in to find out that did not fix the issue. I also unplugged the


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

No Power I have a bosch shx33 dishwasher. I just replaced the water valve because of a leak and now I can't start the dishwasher. It's like there is no power to the unit. I know there is power because I get a shock if I touch the two wires that are connected to the water valve. Is there another trip switch or something somewhere?


First let me say that using parts of your body to test for mains electriciy is a VERY VERY bad idea. You are lucky you are not dead. Please do not touch live parts again, get a multimeter or a mains tester.\015\012\015\012If there is mains across the ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

There is power to the main circuit control board, but no power exiting. unit will not run. no power to display.


There is a possibility that it could be a thermal fuse located in series with the hot side wire. If you are able to find it, and own an ohm meter, find out if it is open. ... Dishwashers

Kenmore Ultra Wash dishwasher model number 665.1374 or 665.1384 I am a technician. This unit does nothing. It has power and ground. I have tested the door switches. They test good. If I unplug the unit and plug it back in then it will run a drain cycle, at least that is what I think it is doing. The motor runs for about 4 minutes. Once it shuts off, there is no further response. No control indicators illuminate. No response from pushing any of the touch buttons.


... Dishwashers

My Bosch SHE98M will not respond to pushing the Cleartouch buttons. It is just stuck displaying the normal wash. It will not respond to pressing any of the touchpads. When the door is closed it displays "not started". I have powered the unit down by switching it off at the supply, then restoring power but there is no change. It appears as if the cleartouch panel is no longer sensitive to touch?


... Bosch Evolution 800 SHE98M05UC Stainless Steel Dishwasher

Can't get unit to start.I have power to unit.


Some open the door in mid cycle ? Try shutting the breaker off and restart the unit. ... Maytag MDB8601AWB Built-in Dishwasher

Lock on led keeps flashing. Can not cancel it, when pressed it also starts flashing. Control touch pad not functioning. When able to get going usually after turning off power for a while, it does not complete the cycle and the lock on led starts flashing again. Thanks


Hi,\015\012The flashing lock light problem might be caused by a stuck key on the touch panel console.If the control board detects that a key is stuck, then the dishwasher will suspend operation until the key is unstuck. If a key without a ... Dishwashers

As soon as power is turned on to dishwasher there is a beeping noise and F1 is lighting up on touch pad screen. What do I need to do?


Hello, welcome to FixYa.\015\012\015\012The first question I can answer easy, what you first need to do is provide a make and model of the unit in question :0)\015\012\015\012I will watch for your reply.\015\012\015\012\015\012macmarkus :) ... Dishwashers

I have a Kitchenaid Kudioflss2 dishwasher.The normal cycle light on the display will not go off. None of the other lights will go on. I've completely disconnected the key pad from the unit and have shut off the power. None of the buttons are stuck down. I tried alternating between two buttons normal ,cancel,normal, cancel etc. and a few other combo's.The manuel under the kick plate is missing.Should i just buy a new keypad(part that lights up) or could it be the interface(part where all the wire


... Dishwashers

Have model ADB1500AWB3 Will not turn on have checked power source tot he machine and will not turn on has touch pad panel and will not activate please advise,


... Amana 24 in. ADB1500AWZ Silver Metallic Built-in Dishwasher

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

Maytag Dishwasher I need the reset sequence for my dishwasher. The power comany had turned off the electric to the house to make chages elsewhere in my house. When the electric was turned back on all appliance came back on except the dishwasher. The dishwasher has a front panel touch pad and three of the panel lights are flashing. I know there has to be a sequence to reset the machine. I also need the peace and quiet in the house since I am the husband and am suppose to know it al


We have a model mdvtt53aww1 and you can push three buttons and will light up the hi temp wash, heated dry and sanitize is there a code make it start ... Dishwashers

My Kenmore 665.15962990 has just quit working. There is water in the bottom that did not drain. The panel is just dead, none of the digital spaces will respond to touch. The stock #15962. There is power to the unit. The door switches check out OK. What should I check next and how?


You have a blown thermal fuse. You can change this by unscrewing the the inner door from the outer door and changing the fuse part#3376359 here is a picture to help you see how to open the unit up.\015\012 ... Kenmore Dishwashers

See below Hi, Disconnect the Power Supply for Few Minutes, say 10 minutes and then Turn it ON. Do you see any Error Message on the Display? Do you see any Other Light Blinking? Have you tried to Press Cancel / Any other Button on the Touch Pad? Is it Working? Do you hear any Beep? Let me know, if needed further assistance. Hope i helped you. Thanks for using ' Fixya ' and have a nice day!! Comments: Apr 02, 2010 - Thanks for your response!! One more detail, i wanted to ask - Is that Wash Li


What's going on here? ... Dishwashers

Maytag dishwasher, has dead control consul, does have power to the board and the latch swithes are good. is there a way to troubleshoot the touch pad? replace the console or the board, or both? thanks, Bruce


The only way possible to see if the touch pads are working is to test the voltage of the control pads when it contacts. The input of the Microprocessor should be checked for the pad control inpulse to come in. If there is no trigger voltage to the mP ... Maytag Dishwashers

Thermal fuse Dishwasher konked out mid-cycle and now no power to control pad. We've already had the thermal fuse replaced once (machine is only 2 years old!) and this appears to be the same issue. I tried to open the front and I think I can see where it is but not sure how to get it out and replace it AGAIN. I wasn't able to get the inside panel completely apart from the front of the unit so I was somewhat limited. I'd rather save the service charge if I can and there's n


Http://www.partselect.com/MultiModels.aspx?ModelNum=KUDS35FXSS&SearchTerm=fuse&RefineSearch=0Maybe this link will help ... KitchenAid KUDS35FXSS Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0777 seconds