Having problems with your Whirlpool 24 in. DU1100XTP Built-in Dishwasher ?

Lights are blinking and nothing happens when you push buttons


Answers :

Have you tried pushing and releasing the sani rinse button, then the heated dry? go back n forth several times. If that doesn't work try the soak and scour and hi temp wash buttons and re post results
Repair Help & Product Troubleshooting for Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Quiet Partner II dishwasher. The clean button is blinking with a green light. When I try to start is over, nothing happens. When I push the cancel/drain button, I hear something happening for maybe a minute, then it reverts back to the clean button blinking and won't take any other commands. What should I try next?


... Kenmore 24 in. 16222 Built-in Dishwasher

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

The clean light keeps blinking and the dishwasher will not start. I pushed the cancel button and it runs for about 30 seconds and just shuts off. Nothing happens when you push the start button.


HiIf clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If ... KitchenAid Dishwashers

The dishwasher won't start, its stuck, pots/pan button is blinking, & the timer has (2)_ _ bars blinking. I tried to reset/pushed the start/resume button nothing happened. I pushed the cancel/drain button still nothing happened. I close the door tight..nothing. I check the trays if there something stuck inside..nothing. I unplug/replug the power cord nothing? my wife was using it when this got stuck about 3 weeks ago.


Did you hold the start/resume button for at least 3 seconds if this works the dishwasher will start ok but if there is a fault it will fail again best you contact your nearest service agent good luck ... Whirlpool GU2400XTP Built-in Dishwasher

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

DU1055XTPQ3 built in Dishwasher... panel has power "cancel" button when pushed you can hear the pump running but on wash the light blinks about 3 times and goes out, nothing happens. Is there a sensor or something in the panel that needs replaced? Jim


Hi\015\012\015\012First try resetting the dishwasher by pressing the AIR DRY button and hold it for 15 seconds. After this if it blinks again 3 times then the control needs replacement. Hope this helps...please post back for further assistance. ... Whirlpool Dishwashers

Quiet partner IV will not start. green light keeps blinking. pushed button, nothing happens.


Hold Air Dry button down for 4 seconds and it will unlock the other buttons. Mine was accidentally locked and therefore none of the cycle buttons would work. ... Whirlpool Dishwashers

Kenmore dishwasher Mod 665 13852K601. MANUAL WASH and CANCEL lights are blinking simultaneously. I unplugged washer and plugged back in. Same thing. Nothing happens when any button is pushed. What's going on?


... Kenmore Dishwashers

Lights are blinking and nothing happens when you push buttons


Have you tried pushing and releasing the sani rinse button, then the heated dry? go back n forth several times. If that doesn't work try the soak and scour and hi temp wash buttons and re post results ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a kenmore dishwasher mdl#665.16022401the clean light blinks all the time and i push the cancel button and then wash and the start and the start button light blinks 3 times and nothing happens.the clean light is still blinking.


... Dishwashers

Maytag dishwasher mdb7601 will not run- light doesn't come on and nothing happens when you push the buttons. Earlier it would work but if you pushed the light cycle button the longer cycle would light up and it would run. Then the time running light did not light up.


... Maytag MDB7100AWB Dishwasher

Lights on Dishwasher light up but nothing happens. When I reset power it lights up the high temp and sanitize button light up and LED displays PF. After I open the door they stop flashing. the far left five buttons light up when I push them and a corresponding number displays on the LED screen. the only lights that do not come on are the Delay button and power button. Don't know if they are working or just don't light up. No matter what lights up the unit does not turn on....:( ? help can't fin


Pf is power failure\015\012 your loosing voltage to the unit \015\012it may just be the door switch or it could be in the control\015\012 try starting the unit but keep your hand on the unit pushing the door in place,, its not a g ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

I have the kitchenaid dishwasher model #kudv03ctss0.the clean light stay blinking and when i hit the start it just blinks and then stops but the clean light stay blinking constantly.if i hit the cancel button i hear a um noise as if it going to turn on but nothing happens and the light stays blinking. what do you think might be the issue .


Dear friend,\015\012ngfam at you service! happy to assist!\015\012It's an electronic problem!The lights are called codes and need to be diagnoed by a factory service person!!We sell appliances for 65 years an ... Dishwashers

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

Dishwasher lights up when Normal Wash is pushed, also heat dry - but when start is pushed all three lights (Normal wash, heat dry and washing) blink then go out and nothing happens. This occurred after a 2 hour delay was attempted last night and no washing ever happened.


What is the make and model so we can better assist you? In the mean time shut power off to the unit briefly, then turn it back on and try a normal cycle. Will be watching for a make and model here. ... Dishwashers

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Kenmore elite model 665.1669 or the 1769 model. All lights are working except for the start button light. When i hit the start button nothing happens. No blinking light, it's like it is dead. Cannot start the washer.


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Bosch SHE43F02UC/50 Lights on, but won't start any cycle....Regular Wash light only one on with timer showing 188.....pushing other buttons does nothing.....no noise, no water fill, just those two light remain on and nothing happens?


... Bosch Dishwashers

I have a smeg free standing dishwasher model df612sdx you turn it on and it bleeps once with a green light on one of the programs. If you push the p button nothing happens along with the start button. If you turn it off and on a few times the program light moves and occassionly it will start then stop a few mins later. Any ideas. Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Dishwashers

Have whirlpool gold dishwasher made in Mexico, the control lock light stays on, when i push it and hold it just blinks three times and then stays on steady and then does the same over and over, before it did this I noticed the lights for different cycles flashing randomly, and even pushing cancel button once in a while would start the machine up....I have tried to unplug the machine and then plug back in, but nothing is helping....any ideas??


... Whirlpool Dishwashers

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

I have a 1 year old maytag dishwasher and it has the touch buttons on top of the door . When you touch the buttons to turn it on, nothing happens. It will light up the type of wash you want e.g. heavy,light...., but it won't start when pressed. It will cancel when pushed, but can't get it to start. HELP!!!


... Maytag Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0825 seconds