Having problems with your Whirlpool 24 in. DU1100XTP Built-in Dishwasher ?

The clean button keeps blinking off and on and will not go to any cycle to clean.


Answers :

Hi
If clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To resolve this error try pressing this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High Temp - Air Dry - High Temp - Air Dry or Hi Temp Scrub, energy saver dry, Hi Temp Scrub, energy saver dry. Now let the unit run for 2-3 minutes and then you press the Cancel/Drain button and allow it to completely drain and reset.
If this doesn't work then it's an issue with the wash pump not pumping the water past the heater efficiently or due to lack of water to heat. Please make sure that heater is not open circuited and is heating the water efficiently. You'll have to check the heater using a multimeter; the meter should read between 3000 to 3300 ohms (Use multimeter on Rx1 ohm setting). If heater is fine then make sure water pressure is optimum and fill valve is working fine. Hope this helps... Please post back for further assistance.
Repair Help & Product Troubleshooting for Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The clean button keeps blinking off and on and will not go to any cycle to clean.


Hi If clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

"Clean light" keeps blinking; dishwasher won't start new cycle


Thank you Daniel Scott. The solution you posted worked for me and saved me calling a technician. My clean light was flashing and I followed your solution to press Heat Dry - Normal twice. And it worked! Thanks so much! ... Frigidaire 24 in. GLD2150RCC Built-in Dishwasher

Cannot start a cycle. The "Steam Clean" button keeps blinking.


... Jenn-Air JDB3200AWS Dishwasher

"Clean light" keeps blinking; dishwasher won't start new cycle


I had the same problem and was told to unplug the dishwasher, wait, and then plug it back in. That didn't work; but I decided to try again. So I unplugged the dishwasher, wiggled the heating element in the bottom, made sure it was in the right positi ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Clean light keeps blinking. Will not start a new cycle. pushing cancel or other buttons does no good.


If this is a Whirlpool manufactured dishwasher (such as the one pictured), the blinking clean light is an interru ... Whirlpool DU1055XTV 24 in Builtin Dishwasher

Clean light keeps blinking and I can't start a new cycle


That is a comon problem with that model. It is not sensing a temperature change in the water. Push i believe it is heated dry and sani rinse going back and fourth between the two to clear the code and see if you can get it to complete a c ... Kenmore 24 in. 15932 Built-in Dishwasher

"Clean light" keeps blinking; dishwasher won't start new cycle


Close the door and to cancel that just press hi temp and hetaer dry again hi temp and heater dry and all the lights is gonna light up, it getting into test mode.\015\012After that press cancel \015\012Now get somebody to replace the therm ... Kenmore 24 in. 17032 Built-in Dishwasher

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

M/N PLD4555RFC3 I get blinking ER message with "wash" "dry" "clean" and "S" blinking icons All buttons have become non-responsive. Tried resetting by disconnecting power but error message comes back Only the Rapid cycle is now selectable. If I allow the unkt to cycle I end up with the error meesage above with the dishes only partially clean What could be the problem?


... Frigidaire PLD4555RFC Dishwasher

Dishes not coming out clean, water is coming out of arms but doesn't appear to be rotating (either top or bottom). Trying to figure out the test cycle on the shu3302uc model (when I hold down pwr scrub and reg wash) the pwr scrub and rinse/hold light will keep blinking when complete, when I use pwr scrub and rinse and hold, both these will keep blinking after cycle is run.


There is a recall repair notice for this model (and several other models) on the Bosch website. There is a faulty controller which may cause a fire! They have an 800 number for setting up a recall repair appointment. Check it out! We just found o ... Bosch 23 in. SHU3302UC Built-in Dishwasher

I have a blinking cancel light on model GU1200xtlt1 and will not start in any cycle. Also if I push another button it flashes rinse button and cancel button. Before this it ran in Sani Clean over and over again and I could not change the cycle. I emptied out a bit of water from the bottom because it did not drain also and the water was not smelling too good.


... Whirlpool Dishwashers

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

Clean light blinks 7 times pauses 1 second and repeats. will not work. the light above the clean cycle indicator blinks 7 times. I can not run the dishwasher, When I press start the light above the start button blinks and will not start


Hi there,\012Well first of all you reset this by pressing - High Temp Wash, Heated Dry, High Temp Wash, Heated Dry, High Temp Wash.If you don't have a heated dry then use "air dry"This sequence help you to reseting the e ... Whirlpool GU2400XTP Built-in Dishwasher

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

WHIRLPOOL ADP 8540 dishwasher has blinking light on all the time (blinking in cycles of 4). When you turn it on (by holding the button down for around 4 seconds) it wont complete the cycle and you need to keep restarting it. can anyone let us know what the problem may be


See this step: ... Whirlpool Dishwashers

Pots/pan light blinks alternately with the normal wash button. Sometimes the cycle will start and then the lights come on. Once they start blinking, the cycle stops and I can't get it to start again. Unplugging it for a few days has worked a few times. But it just keeps getting more frequent. If it does start up, it heats fine and washes perfectly.


... Whirlpool DU1055XTSQ Built-in Dishwasher

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

WHIRLPOOL ADP 8540 dishwasher has blinking light on all the time (blinking in cycles of 4). When you turn it on (by holding the button down for around 4 seconds) it wont complete the cycle and you need to keep restarting it. can anyone let us know what the problem may be. Thank you TD


WHIRLPOOL ADP 8540 dishwasher has blinking light on all the time (blinking in cycles of 4). When you turn it on (by holding the button down for around 4 seconds) it wont complete the cycle and you need to keep restarting it. can anyone let us k ... Whirlpool Dishwashers

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

My maytag mdb6650aww clean button and dry heat button keep blinking do I reset something?


... Maytag Dishwashers

Clean button keeps blinking and no other buttons work except drain button.


... Whirlpool Gold GU2275XTVy Dishwasher

Talking about a kenmore 665.16389300 dishwasher. the "normal wash" button is blinking, but none of the other buttons seem to work and the cleaning cycle will not start when i press the "start" button. any ideas?


Hi\015\012\015\012Open the door.\015\012Within 3 seconds press the following sequence --Try pressing normal wash,\015\012heated dry, normal wash, heated dry, normal wash, heated dry three times within\015\0126 seconds and the ... Kenmore Dishwashers

I have a whirlpool model KuDSO1FL and the clean light blinks and won't start after the cycle has been selected and the start button is pressed. I have tried canceling the cycle but it won't work. The dishwasher was working yesterday and today it drained once we cancelled the cycle and then pressed start but that is all that we could get done. I don't know what the problem is.


Your appliance's clean light blinking will require a service call. It could be several things indicating a problem that are not serviceable by the home owner. You can try turning the power off at the breaker box, then turn it back on and see if this ... Dishwashers

Clean light blinks continuously on and off and dishwasher cannot start a regular cycle or any cycle but when I keep pressing cancel/drain it will begin that for 2 minutes and then right back to same problem


This may or may not help in your situation, but the following link explains how you may be able to clear the blinking clean light problem: ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1395 seconds