Having problems with your Whirlpool 24 in. DU1100XTPS Built-in Dishwasher ?

Hi, Where is the reset button on the Whirlpool Gold Quiet Partner 111 Dishwasher /Model GU1200XTLT3, Type 575-0. When I had my sink faucet replaced, the Control Lock light came on and I couldn't run anything on my Sensory Wash Cycle panel. I tried unplugging it for a while, no luck. All the circuit breakers are fine. THANKS FOR YOUR HELP! Kathy Bonner


Answers :

Hi kalybon,\015\012
\015\012  There is no "RESET" button on Whirlpool Gold Partner 111 dishwasher. :(\015\012
\015\012Regarding your issue, it seems to be a case of Control Card.Sorry to be bearer of bad news, you need to replace that.\015\012
\015\012 The cost of the card in the market is $250. So, i would not advise you to change that.Rest on your's.\015\012
\015\012Any further help, let me know.\015\012
\015\012Thanks for using Fixya.\015\012
\015\012Do rate this solution as "Fixya".
Sorry - there is no reset button on a dishwasher - you likely have an internal problem that needs to be serviced by a qualified repairman.
\015\012
\015\012CLICK HERE for your owners manual in PDF format.
\015\012CLICK HERE for your parts list in PDF format.
\015\012
\015\012It simply may be locked??
\015\012Taken directly from the manual....
\015\012
\015\012Control Lock
\015\012Use the Control Lock to prevent unintended use of the
\015\012dishwasher. You can also use the Control Lock feature to prevent
\015\012unintended cycle or option changes during a cycle.
\015\012
\015\012When Control Lock is lit, all buttons are disabled.
\015\012NOTES:
\015\012**The dishwasher door can be opened while the controls are
\015\012locked.
\015\012** You can turn on the Control Lock while the dishwasher is
\015\012running.
\015\012
\015\012To turn on Control Lock
\015\012
\015\012Press and hold for 4 seconds.
\015\012Control Lock glows.
\015\012If you press any pad while your dishwasher is locked, the light
\015\012flashes 3 times and the selection is ignored.
\015\012
\015\012To turn off the Control Lock
\015\012Press and hold AIR DRY for 4 seconds. The light turns off.
\015\012
\015\012
\015\012If the control panel is faulty - you are looking at $239 for the part plus labor to install.
\015\012
\015\012Thanks for using FixYa !!
Repair Help & Product Troubleshooting for Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, Where is the reset button on the Whirlpool Gold Quiet Partner 111 Dishwasher /Model GU1200XTLT3, Type 575-0. When I had my sink faucet replaced, the Control Lock light came on and I couldn't run anything on my Sensory Wash Cycle panel. I tried unplugging it for a while, no luck. All the circuit breakers are fine. THANKS FOR YOUR HELP! Kathy Bonner


Hi kalybon,\015\012\015\012  There is no "RESET" button on Whirlpool Gold Partner 111 dishwasher. :(\015\012\015\012Regarding your issue, it seems to be a case of Control Card.Sorry to be bearer of bad news, you need to replace ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Hello. I have a Frigidaire model GLD2250RDS0 that starts a wash cycle normally, then stops mid cycle with the 'washing, drying clean and sanitized' lights all blinking. There is no service sheet behind the panel so I don't have a dianostic to run. I have tried the normal things such as unplugging power and looking for obstructions.


This is going to be a electronic control problem. Part #154540101. art can be purchased online at foxparts.com ... Frigidaire Dishwashers

I have a KitchenAid dishwasher model#KUDC25CH.The problem that I am having is the touchpad control panel all of a sudden is lit up like a Christmas tree. Just about every red indicater light is lit. The DW will run but I dont know what kind of wash it is performing or at what stage the cylce is in. I have tried canceling the cycle,I have tried child lock/unlock,I have cut the power to the unit for a few minutes hoping the computer panel would reset itself. I am affraid to run the unit in fear th


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a Diplomat ADP8242 Dishwasher that continues to run during its wash cycle. The machine starts and heats up correctly but will not switch to its rinse cycle and just keeps running with 2 intermitent beeps. I have tried to reset the programe which does pump the water out and resets the control panel, but unfortunatly does not clear the fault. Can you help?


... Dishwashers

Eurotech Model EDW254EWXX runs a 13 minutes cycle before washing like usual, but now it is getting stuck and not doing anything during that 13 minute cycle. No water is running, and it makes NO noise at all. We are not getting any errors displayed. I have unplugged it, and shut off the circuit breaker for 20 minutes, but the problem is still there.


... EuroTech 23 in. EDW254E Built-in Dishwasher

Frigidaire p/n 154493101 was flashing all the cycles and wouldn't reset then when I thought it did I would wash for a min and when I hit the regular wash cycle the no dry light came on couldn't get to the plug so I flipped the breaker and now nothing's lite no power at all tried unplugging and it still has no lights on


... Dishwashers

My KitchenAid Model KUDE70FXSS 2 dishwasher is new to us today and has never been used before. It was hooked up professionally, but I assumed it would work, so tonight when I tried to run it, it lights up on panel, but it won't run any cycles. It will start putting water in the machine, but then cuts off. It starts making a grinding noise underneath the machine, and it clicks like it is trying to work, but the water doesn't wash. Hmmm. Anyone know what to do?


... KitchenAid KUDE70FXSS Builtin Dishwasher

Dishwasher malfunction MOST OF THE TIME it shuts itself down before fully filling with water - SOMETIMES it doesn't shut down until the minute the wash pump starts - SOMETIMES it washes for 10 or 20 minutes before shutting down - SOMETIMES it will even run a whole cycle, BUT it doesn't open the soap dispenser door - tried doing a diagnostic run but after it turned on all the lights on the panel it started to fill with water and shut itself down......... HELP


Follow this steps and fix it. God bless youFloat Switch\012\012\012The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. Check the ... Dishwashers

Maytag dishwasher model MDB7609AWW2 has a blinking clean light. I followed the advice on fixya (thankya!) and by alternating the normal and heated wash buttons I was able to return the lights to normal. However, once I tried to run a normal cycle, it didn't do anything other than fill and drain. I then ran the hot water faucet in the sink until hot and tried another new cycle, but no luck. Any advice is MUCH appreciated!


... Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

We have a Kenmore Ultra Wash Dishwasher Model number 665-13859K601. The Normal wash and the Cancel (drain) buttons are flashing red on the control panel. No matter what we have tried, we have been unable to correct this problem. Obviously the dishwasher does not function. When you close the door the lights keep flashing and no button combinations seem to do anything. I have looked at the troubleshooting guide that came with the dishwasher, however there is no


... Dishwashers

Kenmore Limited Edition Ultra Wash Dishwasher. Model 665 15892100, Ser. FL4910642 E71195, Stock #15892. Loaded dishwasher, started it, and went to store. When we came back, it appeared cycle had not completed (greasy and wet dishes) and the dry cycle had definitely not run. Bottom of dishwasher is filled with water. Tried to cancel/start the machine but control is completely blank and does not respond.


Hello,Welcome to FixYa.The issue with your dishwasher is more than likely the "thermal fuse" inside the control panel...it is all too common with those machines unfortunately.I've at ... Dishwashers

My dishwasher (kleenmaid brandt super silent DW121TB) appears stuck in a wash cycle; how do I reset the program? I have read the instruction book to no available, tried unplugging power overnight, tried a combination of simultaneously holding buttons in and switching on, letting the machine run all night, drained the water and added clean unsudded water, and none have corrected the situation. There is also a selection lever inside the machine that is not identified in the instructions, it appea


When you say it is stuck in a wash cycle, do you mean the wash arms are continuously running?\015\012Is there water in the base when you open the door?\015\012\015\012Can you try to run the dishwasher in any other program like rinse ... Dishwashers

Whirlpool DU1145XTPPB7 Whirlpool DU1145XTPB7 model. Normal cycle light started blinking sometime during end of wash cycle. It will not do anything. Things I have already tried and not worked: 1. Unpluged and pluged unit back in. 2. System reset w/ heat-dry button, etc. Any help would be greatly appreciated


These dishwashers normally have a "Control Lock" mode.  It's in the manual.  It is provided for child safety.  It's often controlled by holding the "No Heat Dry" button for 4 seconds or more -- same procedure turns it on or off. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Kenmore Elite dishwasher Model #665 1597 2992 Machine fills with water but thereafter it neither washes nor drains. Machine will not drain when I advance the cycle by pressing the Cancel/Drain button. There was a report that there was some noise when the machine first failed. I do not hear anything when I try to run a cycle. What might the problem be? How does one turn the motor manually to see if it is bound up by something? If it is the motor do I want to pay an extra $70 to $100 and


... Dishwashers

Kenmore 74362 My model# is 665.74362400 this unit is only just over one year old. My problem is it shut down and the quick rinse light started blinking. I have tried some of the button-reset procedures that were on some other responses but to no avell I even left it unplugged for a while. Any impute would be appreciated. I have a Kenmore Dishwasher Model #74362. After we run a cycle for a normal wash and heated dry the dishes are all very dirty and greasy. It is as if they were never washed. Th


I had the same issue and you will never beleive the solution.\015\012Steps to follow:\015\0121) run one full cycle with no dishes or soap\015\0122) run one full cycle with a dishwasher cleaner like Jetdry\015\0123) run one ful ... Dishwashers

I have a Kitchenaid Dishwasher, model KUDM01TJWH0. It runs through the washing cycle properly, but then the Rinse Only light begins to flash and it does not drain. I have tried hitting the Cancel/Override button (also tried hitting all other buttons, but they were ignored too), but it also begins to flash with the Rinse Only light together. If I unplug it, wait a few moments, plug it in and all the lights are off when it comes back on, wait a few moments and hit Cancel/Override, it empties and s


... KitchenAid Dishwashers

I am stuck on the rinse cycle. it wot allow me to set it to anything else including a normal wash. Have tried unplugging but its still only rinsing. Please help!


Unplug, remove tub by rextending out fully and uncliping lock tabs at front of slider. lift tub out and support on a chair. the circuit panel on bottom left floor area needs to be dried out underneath, there is a water sensor below this panel and if ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dishwasher just started leaving food residue on dishes after washing. We usually don't rinse beforehand but even when we do this it's still happening. Can I run something thru a cycle to give the washer a good clean out? I've cleaned the filter (nothing there), tried to clean the spinning arm as well as I could and looked for any other food that might be clogging things up. Dishwasher came house - think it's about 6-8 years old. Otherwise works great.


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... GE Nautilus 24" Built-in Dishwasher

Built in model MDB5601AWB- about 3 years old. The touch panel stopped working..no lights would come on when touched. Tried it a couple of days later. Lights came on..finished a cycle. after satying in the wash mode for a few hours. Then lights started flashing on and off. At that point I shut it off at fuse box since I couldn't get lights to stop blinking and haven't trusted to use since


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. From what you have described it seems to be the ... Maytag Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2108 seconds