Having problems with your Whirlpool 24 in. DU1100XTPS Built-in Dishwasher ?

Clean light flashing off and on dishwasher will not start

\015 The clean light keeps going off and on...i cancel and it still goes off and on....ive tried to start as usual...but when i hit the start button it goes off.\015

Answers :

This may help in your situation. The following link explains how you may be able to clear the blinking clean light problem:

http://www.fixya.com/support/r417123-blinking_clean_light_kenmore_whirlpool

Now...keep in mind all dish washers are not alike and have different panel options. If you do not have the same set up as I have referenced, the tech sheet for your dishwasher will explain. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting.

NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.

Sometimes this can be a momentary glitch in operation. However, if the problem keeps reoccuring the number of flashes is an indication of which circuit is causing your problem. Again, refer to your tech sheet to determine this.

If you have any questions, please let me know. I hope this helps you solve your problem.
Repair Help & Product Troubleshooting for Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

Diswasher malfunction - won't start clean light flashes 7 times The clean light keeps flashing green. Can't get the washer to start. The only operation it will do, is drain when the cancel / Drain button is pushed This unit is: Stock # 16029 Type # 575-0 Model # 665.16029.402


This information may help in your situation. This can be a common problem on some Whirlpool manufactured dishwashers. The following link explains how you may be able to clear the blinking clean light problem: ... Kenmore 24 in. 16029 Built-in Dishwasher

Allan Dishwasher won't start. Clean light keeps flashing. I have tried cancelling a couple of times, and it goes through a 2 minute process and goes right back to the flashing clean light and not allowing it to start.


Turn off the power at the breaker to the DW and wait 15 seconds and then turn it back on and see if problem is fixed. Reboots the controller. ... Dishwashers

My Miele intake/drain light is flashing. It seems to be an intake problem, because water drains out fine, but seconds after water starts going to the machine, it stops and the intake/drain light starts flashing again. We've cleaned the filter in the inflow hose, cleaned the arms, and it still doesn't work. Any suggestions?


... Miele Touchtronic G892 Built-in Dishwasher

Dishwasher won't start. Clean light keeps flashing. I have tried cancelling a couple of times, and it goes through a 2 minute process and goes right back to the flashing clean light and not allowing it to start. I have already tried shutting off the breaker as suggested by someone but it did not solve the problem. Any other ideas?


Hi\015\012 \015\012Thanks for using FixYa. If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks t ... Dishwashers

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

First 2 weeks ago i put an electric control module into the upper section. what comes on is the green flashing light for clean. in checking connections i found the paper for trouble shouting. i did what they said to do. they said hit the time saver - high temp - time saver - high temp. from there all the lights went on & the wash cycle started and ran. then it just stopped & the green light for clean just flashes. the water is still in the bottom & won't drain.


The error indicates that the machine has taken too long to drain the water. Do the following.\015\012 \015\012\015\012Switch off the machine, unplug or disconnect the ma ... Kenmore 16874 Built-in Dishwasher

Hotpoint BC145 Dishwasher not cleaning starts to kick in but then just sticks on the "R" light flashing and cannot reset even after turning off. Itbeeps when pressing the select button sound weaker and shorter than they used to and the light does not move from the "R". On a couple of times I have tried it has reset and then the dishwasher starts but after about 3 minutes there is a low beep(not the usual beep when a programme finishes) and the washer stops and the light is flashing on the "R" ag


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

Kenmore 665 17033400 Elite dishwasher clean light flashes 7 times and it wont run. i used the reset combination, all lights lit and stayed lit until i pressed reset. Then it started a wash. now the wash seems to be finished, though i am not sure and the clean light is flashing 7 times, pause, 7 times, etc.


That signals an issue with a faulty heater &/or heater drive circuit.(that info comes from their troubleshooting guide)I ran into it this weekend and discovered that the heater coil in the bottom of the washer was broken. ... Kenmore 24 in. 17032 Built-in Dishwasher

The CLEAN light is flashing on my Kenmore QuietGuard3 , but it won't clean anything. It starts a cycle for a few minutes, stops and starts flashing clean again. Any suggestions?


You will have to reset the dishwasher. First try and turn off the mains power and back on after a short time. If the clean light flashing starts again then you go through the hard reset procedure. press NORMAL WASH then HEATED DRY buttons on ... Dishwashers

Kitchenaid kudso1flss1 is stuck in clean mode. clean light flashing on and off. tried to reboot by unplugging, when i hit cancel it goes into "empty water left" mode, then goes back to "clean" light flashing on and off. Can't get it to go back to "start ready" position.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This is the first thing I'd try, based on your description. ( the clean light is an error code in this case ) On your control panel, If you press these buttons in sequence then close the door it ... KitchenAid Dishwashers

The CLEAN light is flashing on my Kenmore QuietGuard3 , but it won't clean anything. It starts a cycle for a few minutes, stops and starts flashing clean again. Any suggestions?


... Dishwashers

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

Model #PLD4555RFC0 The control panel lights on the front are all flashing and start cancel button will not change anything. flashing Er with wash, dry, clean, and and S showing. Top controls have China/Crystal light flashing and Low rinse agent light flashing. Nothing seems to work


... Frigidaire Dishwashers

I have a kenmore dishwasher mo. no.665.17039401 the clean green light flashes 7 times and it keeps doing that if i try to start the dishwasher on the start button a red light flashs three times what do how do i fix it .i made shure the door was locked


... Dishwashers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Kenmore dishwasher 665.16029402./ clean light flashes 7 times. i did the push button sequence to reset. started to wash for awhille and during the wash it stops and green light starts flashing again


... Kenmore 24 in. 16032 Built-in Dishwasher

Whirlpool dishwasher Clean light is flashing, we just bought it last week and after the third wash, the Clean light started flashing and it won't go off, which stops it from doing anything else. User manul says to have it serviced, but that seems unneccessary. It doesn't seem to be draining completely, so there may be a knk in the pipe, which may be related, just not sure


The blinking clean light is an interruption in the dishwasher program that either indicates a malfunction, or a simple program glitch. The following link explains how you may be able to clear the blinking clean light problem: ... Dishwashers

Zunussi ZDT6252 dishwasher will not start The number 3 programme light flashes and clicks and the on/off indicator light flashes. Water pressure and electricity fine and filters have been cleaned. Cycle does not start at all.


Hi. Do this. Go to your electrical panel for the house and turn off the breaker or remove the fuse for your dishwasher. Leave it off for 5 minutes. This will cause the machine to reset. After the 5 minutes pass, turn the power back on and check ... Zanussi 23 in. ZDT6252 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1345 seconds