Having problems with your Whirlpool 24 in. DU1148XTP Built-in Dishwasher ?

Water not draining in the bottom of the dishwaser,no power at all

\015 Water not draining in the bottom of the dishwaser, no power, it is plugged in and the circuit breaker is on.\015

Answers :

If you have a row of buttons on the left side for heat cycles check them a shorted switch will cause a loss of current situation so that the drain solnoid wont activate
Repair Help & Product Troubleshooting for Whirlpool 24 in. DU1148XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

I have a kenmore 665.13719k601, i used the delay switch and now i found water in the bottom of the machine. the cycle most have stopped while i was away. when i returned there was water sitting in the bottom of the machine. The water is clean... I can not drain due to no access to power on the machine. I checked the breaker but it was on, so i reset it anyway... nothing.. any idea's


... Kenmore 13719 / 13712 Built-in Dishwasher

Not draining we have a ge quiet power dishwasher it started not draining fully, I took the hose off under the sink and seemed to be lots of water running when i put it on rinse cycle but when I opened it up still water in bottom just wondering what it could be?


Are you sure your drain system is not clogged or restricting water flow ? When you say youtook off the hose off under the sink and it seemed to be lots of water running on the rise cycle .. that suggests that you may have a restriction af ... Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Water not draining in the bottom of the dishwaser,no power at all


If you have a row of buttons on the left side for heat cycles check them a shorted switch will cause a loss of current situation so that the drain solnoid wont activate ... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hobart LXIC under counter comerical dishwasher. Delime lled keeps comeing on every time power up. Checked sensors on bottom in the water drain area senser on right (there are 2 next to each other on this unit I think other is water temp) the wire had wire burn completely off. I reconnected the wire and started to burn up the wire again. Question: 1) Is this sensor for the Delime sensor? 2) does it sond like the sensor is shorted to you? or sending wrong voltage to sensor? 3) If no


... Hobart 24 in. LXIC-5 Built-in Dishwasher

I have the Triton Triclean Wash System Quiet Power II fro GE and it will not drain after the cycle. About 2/3 inches of water sitting at teh bottom. How do I get the dishwasher to drain?


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Dishwasher LFK-011S: First it occasionally gave four beeps (overflow) but no water in bottom or under. I then noticed that with lower water pressure machine worked ok few months. Now last week in the middle of program, drain pump started to run, machine gave four beeps and pump kept running even main switch off. Now when I plug in power cord, the pump starts to run immediatelly


... Fagor LFA013 SS 23 in Builtin Dishwasher

The problem started with it not draining correctly and leaving water in the bottom - my husband took it apart and found a bolt in the drain. He removed it and now it won't start. It appears to not have power to the electrical panel- we have reset the breaker several times - left the breaker off for 10 minutes thinking it might erase the memory - I've asked for instructions to reset and I keep getting info that is very far removed from this model. I know it has a protocol because a repair


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012The reset on your dishwasher is as follows, ( I can't locate your particular model number...but its madw be whirlpool so there are only a couple of possible sequences ) however depending ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a GE Quiet Power 3 dishwasher and water is not draining completely after the wash cycle completes. There is about an inch of risidual water in the bottom of the washer after the wash cycle is done.


... General Electric Adora GHDA670N Built-in Dishwasher

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

Our Beko DE6340 has stopped working. We turned it on as usual and left it to run. Several hours later we opened the door and the was water in the bottom. This has happened before so I slid the unit out took out the drain and reattached. Now it won't turn on. I have taken the top panel off an there is power to the switch but no lights are coming on. Any ideas?


... Dishwashers

My Kenmore 665.15962990 has just quit working. There is water in the bottom that did not drain. The panel is just dead, none of the digital spaces will respond to touch. The stock #15962. There is power to the unit. The door switches check out OK. What should I check next and how?


You have a blown thermal fuse. You can change this by unscrewing the the inner door from the outer door and changing the fuse part#3376359 here is a picture to help you see how to open the unit up.\015\012 ... Kenmore Dishwashers

When pressing any front button on the control panel nothing will light up or start up in any manner,does look like it did not finish draining,have water sitting in the bottom. Pulled off front access panels no signof burned wires or anything becoming disconnected? do have small childern in the house pressing buttons? power is good going to unit.??


1)check any fuse blown in board.\015\0122)check supply to the board. ... Kenmore Dishwashers

Dishwasher restart Please help! I started a cycle and about 1 hour later I went to check and it was no longer working- no power at all. There is water at the bottom inside but I can't make it drain. This happened once before and the technician people gave me a way to restart the dishwasher by pressing certain buttons - I can't remember which ones. Does anyone know??? I need help!!


I don't know about a button sequence but I would suggest that you turn off your breaker and then back on. That will reset most electronics. ... Kenmore 15129 Built-in Dishwasher

There are no lights on the control panel and water in the bottom of the washer that will not drain. AC power is good.


... Whirlpool 24 in. GU2548XTP Built-in Dishwasher

No Power? I opened the dishwasher one day to find that it had only run half of the cycle. There was still water at the bottom of it. When I drained it, I attempted to turn it on...nothing. I have turned the breaker off and on, but still nothing. What could be wrong?


I would start at the junction box at thee bottom of the d/w behind the access panel to see if a wire nut may have burnt off. Be sure to turn the breaker off before you check this. Next I would check the door switch. ... Dishwashers

I have a Kenmore Elite dishwasher (model 630.17303406) and it just stopped working. Doesn't drain what's left in the bottom and just makes a humming sound when turned on. Power is good, sounds like the motor is working. Doesn't seem like it is drawing water in. I want to check the pump and motor, anybody have any advice?


If nothing obvious like blocked / obstructed outlet pipe\015\012You need to check if the outlet pump motor in line with the outlet hose is spinning when in the outlet mode. First check if it is spinning by looking at it and see if the small fan ... Dishwashers

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Magic Chef DU4K is not draining all the water. There's at least a gallon of water standing in the bottom. I have cleaned the air gap assembly and drain line completely. They were even sanitized in hot water. I do not hear the water draining like it use to. When it worked properly you could always hear water draining into the GD. Now I can hear any draining. Again, there is no clogging anywhere in the drain line assembly. Is it a bad pump. I don't know where to go next with this.


... Magic Chef Dishwashers

I have a Bosch Diswasher that is not draining. I have disconnected power for 35 minustes and used shop vac to excess water out of drain line. i also pulled all water thru the drain line from the tub itself. i assume that because i could pull the water, all baffles and lines are clear as i emptied the tub from drain line. you can hear the pump come on to drain water but no water is moving. What would be my next step. If it is to replace the pump, how do i easiest access the pump to remove and rep


Either the selector switch or pump is faulty. If there is not any clogs anyways. The system may need to be reset. Most resets are done by entering a series of numbers on the touch pad to enter diagnostic/test mode where the machine can be reset. This ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1480 seconds