Having problems with your Whirlpool 24 in. GU1200XT Built-in Dishwasher ?

Clean light blinks. It blinks 7 times, the pauses before blinking 7 times again. Code? Cancel starts the dishwasher, but shortly turns it off. No other control works.


Answers :

Hi,

This machine was made by Whirlpool and the flashing clean light is a common error code for them.
If\015\012the clean light is the one flashing then your dishawasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder than it is used to getting.
Repeatedly press the Heated Dry and Hi-Temp Wash(scrub) which ever yours has untill all the LED lights come on, press cancel twice and\015\012try the dishwasher again making sure to run the water at the kitchen\015\012sink till it is hot before starting the dishwasher, if this trips and\015\012locks you have a problem with the heating element, or temp sensor.
Press\015\012the heated dry button followed by the normal cycle button, and then\015\012repeat once. You should see all of the lights come on for a second or\015\012two, and then the dishwasher will work again.
If you haven't\015\012already, take a look under the kick plate in front to see if there is a\015\012schematic tucked in there somewhere. Whirlpool has put their\015\012diagnostics for specific models on these.
I don't have the specific repair manual for you model.
So, if the above combination does not work here are two more that have worked for me.
HiTemp Wash + Air Dry + HiTemp Wash + Air Dry in less than 5 sec
or
Hi Temp Scrub/Scour + Air Dry + Hi Temp Scrub/Scour + Air Dry in less than 5 sec



Let me know, if you need further assistance.


Hope i helped you.


Thanks for using ' Fixya ' and have a nice day!!
Repair Help & Product Troubleshooting for Whirlpool 24 in. GU1200XT Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Clean light blinks. It blinks 7 times, the pauses before blinking 7 times again. Code? Cancel starts the dishwasher, but shortly turns it off. No other control works.


Hi,This machine was made by Whirlpool and the flashing clean light is a common error code for them. If\015\012the clean light is the one flashing then your dishawasher could have a\015\012heater circuit problem (depending on t ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.\015\012So remove the panel and disconnect the wires, check all lead ... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

I have a Miele Dishwasher 2430 Sci. It's been not used for 5 months and when I returned it worked fine for several times (at least 6). NOW the intake/drain light keeps blinking. I have already cleaned out the drain and replaced it properly (there was nothing in there and it was clean). No water is coming into the dishwasher?however I know that the water hook-up is on (the first thing I checked). I turned the water on and off several times and AM SURE it's on now. What else could be


The usual course of events is to check and clean the filter, check and clean the water pump and well, check and clean the waste pipe and any connection to a sink or waste disposal system, then check the inlet warer pressure, then the machine level / ... Miele G2430SCi Dishwasher

Hi. I have an innovation Fagor dishwasher. worked perfectly the first time. Next to the display screen is a place "op" and "fin". when i turned it on the second time the "op" light blinks continiously and no other button such is the operate button works. thanks


... Fagor LFA-013 Stainless Steel Built-in Dishwasher

I have a 6th sense dishwasher purchased new October 2004. It has been working properly and then has just stopped the next time I tried to use it - it will not turn on no matter what buttons I push - no response. I have checked the power out let with another appliance and that works so it is not the power supply from the power point. I can only think it must be a fuse or the controller. Can you please advise best course of action? Thanks Helen


I rang the appliance man to fix the problem.\015\012\015\012Thanks anyway Helen ... Westinghouse Dishwashers

One day the diswasher was working fine...the next time it turned it on it ran for about 3 min. then shut off and seemed to have no power. I checked the breaker...it was fine. A few days went by and all of a sudden the lights were blinking on the panel. So I pushed the cancel drain button. The water drained out and I then proceeded to load the dishwasher and turn it on again thinking it was just a fluke when it shut off earlier in the week. It did the same thing...ran for about 3 min and then shu


... Whirlpool GU2200XTSS Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Helloo! Dishwasher candy futura cdf 312A not work. On button 50 and 1/2 at the same time flashes controls light. I hear drain pump how to boot. When I turn dishwasher off-on defect not disappears. Please help me.. Thanks


... Dishwashers

Hobart lx18h Our commercial Hobart dishwaser stops working after running a few cycles. After pressing start the LED display will continually blink and nothing will happen. We'll turn it off and on again a few times to reset it and it will start up again eventually. We've had an appliance guy look at it multiple times. He's replaced a part or two for it but the problem continues and he isn't much help. Anyone else had any similar issues with this model of dishwasher?


... Dishwashers

I've had a Miele G892 SCU PLUS dishwasher for a long time. Today a problem started that results in a flooded floor. Water keeps flowing into the dishwasher - even when the unit is turned off. It seeps in very slowly, but within15 minutes there is enough to overflow & flood the floor. My guess is that there must be some kind of sensor that isn't working, or the coresponding mechanical switch that shuts off the water is worn or slightly stuck open a bit? Anything I can do / check, short of the re


... Miele Touchtronic G892 Built-in Dishwasher

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


... KitchenAid KUDC10IXSS Builtin Dishwasher

My Maytag dishwasher goes for long stretches when it won't turn on even though I push the proper buttons. The buttons won't light either. It turns on by itself after a couple of weeks of sitting idle. Some of the lights may blink on the start panel while the dishwasher doesn't work, but only on occasion will it fully operate. I have turned off the power and turned it back on, hoping to reset the computer part of the dishwasher. It didn't work.


The Control Touch Panels like to fail on may brands - especially Maytag. They are sensitive to humidity - and a lot have the vents out the front - right by the control panel.Please reply using "continue with this expert ... Maytag Dishwashers

Every aspect of the dishwasher works except that it wont drain. After a short time on the drain cycle it turns itself off.


There could be something stuck in the pump. If you have a wet vac, you can try vacuuming out the water from the drain hose (it probably connects to the drain under the sink). If you try getting it back to the drain part of the cycle, and vacuuming ou ... Frigidaire Dishwashers

Dishwasher would not work and clean light would blink seven times. Asked an expert and they said to hit saniwash and heated dry two times. This work for a couple of times but now the dishwasher acts like there is no electrical power goimg to it. I tested the power with a voltmeter and there is power going to the circuit board.


Normally this happens when the dishwasher electronic control does not detect a water temperature increase during the main wash cycle. The issue could be in the heater element, the thermostat or the wiring that is connected to those or on the electro ... Dishwashers

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

I have a Kitchen aide dishwasher Model KUDI01ILWH6 that will not turn on..there is a control lock light on and I have tried pushing the cancel button but all that happens is the control lock light flashes 3 times and the dishwasher still wont turn on....Please , how to I disengage the control lock


... KitchenAid Dishwashers

My De Dietrich dishwasher turns on but then turns off after a couple of minutes with no water entering dishwasher. I found some instructions and turned on and off 5 times (and unplugged). This worked once and full cycle ran but not the second time. Not sure if it is worth paying 165 call out charge or getting new machine as 7 years old


... De Dietrich 23 in. DVF110J Built-in Dishwasher

The control panel keeps on blinking and the dishwasher won't work


It seems likely that the machine is trying to tell you that something is wrong and that you should do something.The most likely thing is that the filter or pump is clogged and needs cleaning.There is an internal filter which ... Whirlpool GU2400XTP Built-in Dishwasher

Ever since it was brand new, About once in every four or five times I try to turn on my KitchenAid dishwasher, it won't start. The start button blinks and beeps. I have to open the dishwasher an


... KitchenAid 24 in. KUDM25SH Built-in Dishwasher

FDB834RFS0 FRIGIDEAIRE DISHWASHING M# FDB834RFS0 Precision Wash System.... All control panel blinking.... Main power turn of and repower then ONLY HI TEMP WASH and NO HEAT DRY LIGHT ON. How do I enter control panel mode to clear blinking lights? Could it be faulty element inside dishwasher? Any suggestions gladly appreciated. Tks .. AA


... Frigidaire Dishwashers

The contol lock LED is illuminated on the front panel of my Maytag dishwasher. (Neither my wife nor I pressed the control lock for 3 seconds!) We've tried to extinguish it by pressing it for 3 to 5 seconds, but it remains ON. We've turned off the breaker to the dishwasher overnight, but when we turn the breaker back On, the contol lock LED comes on. We simply can't unlock the control panel. We can tell that all of the other buttons work just fine because pressing any of them causes the 3 Sec LED


If by pressing the control lock button for 3 seconds does not solves the problem.then there are 3 possibilities due to which this problem may occur\015\0121)the door is not closing properly. the dishwasher door latch is either cracked internally or t ... Maytag Dishwashers

I have a whirlpool dishwasher DU915WKSO: when I turn the dishwasher on, the heating element comes on but no water comes into the unit. I recently replaced the garbage disposal and th dishwasher worked fine for a time or two. Since then I have only been able to get water in it once. Like I said, the heating element works but no water in the dishwasher. Thanks for any help.


... Whirlpool DU1055XTS Built-in Dishwasher

My Hoover dishwasher HFI 3015 is not working. When you turn it on, the P1 and 'out of salt' light is flashing and bleeping constantly. I believe that it may have run out of salt yesterday, but I have filled it this morning and there is plenty of Dishwasher salt in the compartment now and it is overflowing with water. I have tried turning the machine on and off, but each time I turn it on I get this bleeping and flashing and can't stop it. Any ideas?


... Hoover Dishwashers

My Kenmore 15652 dishwasher has the Pots/Pans light blinking. When I try to press cancel the quick rinse light also blinks, as well as the cancel light and the pots/pans light. When I release cancel the pots/pans light still blinks and the other two turn off. How do I reset dishwasher so it works normal?


... Kenmore 24 in. 15652 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2389 seconds