Having problems with your Whirlpool 24 in. GU1200XT Built-in Dishwasher ?

Dishwasher starts mysteriously by itself. No one was near the machine or pressed any buttons. What would cause this problem?


Answers :

Repair Help & Product Troubleshooting for Whirlpool 24 in. GU1200XT Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher starts mysteriously by itself. No one was near the machine or pressed any buttons. What would cause this problem?


... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Hi there. I have a Matsui MF145 slimline dishwasher and having a problem. When I press the on/off button I would usually then press the program indicator button (usually the first indicator - pans) and close the door and the dishwasher would start. Currently i press the on/off button and try to press the program indicator button and the on/off button flashes and there is a continuos beeping sound....and nothing more happens. Do you know what the problem is?


Try to clean the unit, ofetn when the machine is dirty, some sensors are fooled thinking there's some problem. be sure there's no jam on mechanical parts. ... Dishwashers

Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

Have a KUDS24SEAL5 superba and no lights come on after pressing any of the buttons. Power to machine is good. Several months ago it would not start properly by pressing 'start'. Would go directly to 'drain' cycle. Then found that if we pressed 'rinse' before 'start' it worked fine. Now, almost a year later...no lights, no one home...any thoughts?


I had a KUDP02CRB and there is a hidden transition connector on the front panel under a black plastic cover that was pulled out a little. It connects the flex cable from the controller board to flex circuit of the panel. I just pushed it back in al ... KitchenAid Dishwashers

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi


... Maytag Dishwashers

The start/pause button beeps when pressed to start a program and the machine gives a beep in response and appears to start its initial sump emptying phase but stops within 1-2 secs. Have checked pump and found no problem but start time is so short that in cannot have sensed a problem in the pumping circuit. If I persist in holding the start/pause button in, it can be released after the initial sump emptying phase (2-3 mins) and phase 1 of the wash program goes to completion. At the end of the


Hi\015\012\015\012Ronald...the beep sound itself indicates an issue with the\015\012membrane switch (control panel) and it should be replaced. I believe that the\015\012pump and motor is fine as its just beeping and doing nothing else. Ho ... Smeg 24 in. DWI612 Built-in Dishwasher

I have a F&P dishwasher model DW60CDX1 (around 5 years old) which we cannot start a cycle. The dishwasher turns on (power button and all programme indicators light up) but when you press a programme button nothing happens - the lights don't change. We have switched the power off at the powerpoint and on again a few times but this has not rectified the problem. It was playing up before this in that sometimes the programme would not start when a button was pressed but I just closed the door mor


The micro switch in the door which senses the door closing has probably failled. This is accessible once the inner door cover is removed. Switch should be under $10 from electrical store. Or buy through appliance manufacturer. ... Fisher and Paykel Dishwashers

I have a zanussi tempoline dishwasher, I have loaded this as I usually do, turn the knob to the right and select the 2nd programme the light next to this comes on, I have pressed this to start the machine although it seems as if it is going to start this light flashes and the top arrow on the right of this flashes intermitanly, but the machine does not start the wash programme. The 3hr delay button if I had pressed this by mistake which I am sure I have not would light up. When I found it did no


Hi Ruth.The machine can be in error mode. In this case one or more lights in the control pad will stay on or flash and the cycle will not start.One of the most common fault in your situation, and at start of the cycle is no wa ... Zanussi Dishwashers

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace. ... Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

The start button light is very dim and the machine will not start, all other buttons and lights seem to be fine. The problem came about gradually some times it would work other time not, now not at all. the machine is about three years old.


... Amana 24 in. ADB1500AW Built-in Dishwasher

Have a 4 year old Kenmore Dishwasher Model # 74382. No problems at all until last week I went to start it and it would not turn on. Lights on the control panel were on with exception to the start light. I opened and shut the door to make sure it clicked and pressed the start button again and nothing. I tapped around the panel with the side of my fist and pressed it again and it began working. Well today different story I went to start it and it did the same thing. I tapped all over front of the


The problem is more likely the door switch is failing or out of adjustment/loose. You will need to remove the door panel. This is easy to do. There is a video at ... Kenmore 24 in. 74382 / 74384 / 74389 Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

I have a Kenmore Type 575-0 Dishwasher, model number 665.16033401, Style 16033. It runs trough the cycle, once the cycle is complete the clean mode light is on but most dishes are still dirty. I had someone here to repair this about a year ago. All he did was press alternating two buttons, which I have tried, it resets and lets you start a new cycle. However, the problem remains. Last time there was only button pressing involved, no need to replace anything. So, I would hate to have to pay ag


You need an electronic control and heating element ... Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

The standard procedure to start the machine is to select a cycle (normal, dry heat, etc) then press the start key. Currently when I select the cycle and the cycle LED is on, pressing the start key does not start the machine. I can press cancel, then start and then choose the cycle and it will work. Also, if I first press the start key, the machine will start and the previous wash cycle selection LED will light up and that cycle will run. Do I have a problem with the keypad or the con


... Kenmore 16632 Built-in Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

The hidden control panel has only about half the lights showing what function is pressed. A couple of days ago the washer would not start. The only function which would work was the far left sensor light. After trying to cut power and pushing other buttons, to no avail, we let the machine sit a couple days. It now works again with only half the lights on function pad working. It acts like there was a electrical short.


First retrieve the tech spec sheet behind the toe-kick panel located near the floor and run the diagnostics if it will let you do so w/o the full operation of the keys on the pad,then if it wont the touchpad or keyboard on the front that you use to s ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Dishwasher flooding Hi my Asko D1716 Super Cleaning System Dishwasher has started to have a flooding problem. When the cycle finished last night it seemed fine then in the morning the machine was full of water, I scooped out the water and by this evening the machine had flooded onto the kitchen floor. I tried other solutions I found on this website but they didn't suit my dishwasher as it doesn't have the appropriate buttons. Any suggestions would be appreciated!


When you say that you tried other solutions.. it's hard to know which you've tried and which you haven't so I will suggest some basics first.. ( if you've tried them, then disregard)...\015\012Have you checked or addressed the following:\ ... Asko D1716 Built-in Dishwasher

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

Initially It started washing, completed the entire cycle, then while drying began re-washing the load. Then it would start washing nothing, without any buttons pressed. Then it woldn't allow any buttons to be pressed for any cycle.Then the lights would flash, but nothing would progress through the cycle.


For replacement parts - head on over to PartSelect.com or \015\012RepairClinic.com and enter in your full model number for a full parts \015\012listing.\015\012I recommend both sites because ...\015\012\015\012\015\012FixYa ha ... Whirlpool GU2300XTVQ Builtin Dishwasher

I have Whirlpool dishwasher about 3years old it is the ADP7966 AAA 6th sense. When I put it on and turn the temperature knob, only the first temperature green light comes on althou I can turn the knob all the way round none of the other lights come on, my rinse aid and salt programmes light up thou ,and when I press the start button it flashes twice stops a bit then flashes twice again, and thats all it keeps doing. I would be very grateful if you help to solve the problem. Many thanks to you.


... Dishwashers

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1670 seconds