Having problems with your Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher ?

Kenmore Dishwasher installation

\015 New Kenmore dishwasher, with legs unscrewed and removed and back wheels at highest setting, measured 33 1/2 inches high. Opening under counter measures 33 1/2. Installers say it won't fit. Any solutions? Thanks\015

Answers :

It sounds like you either replaced your floor or your counter tops/cabinets.
\015\012
\015\012Your 2 options are to:
\015\012
\015\012
    \015\012
  1. Remove the flooring, (i.e. tile) to the toe kick of the cabinet allowing the dishwasher to drop in. I recommend reinstalling the legs on the dishwasher if you have the room after removing the flooring.
  2. \015\012
  3. Trimming the cabinet/counter top. This is assuming that you have room to trim.
  4. \015\012
  5. Shimming the counter top up to raise the countertop up 1/4" to 3/8".
\015\012I recommend having the legs on the dishwasher. This helps in leveling. Be sure to attach the dishwasher to the counter top. This will keep the dishwasher from moving.
\015\012
\015\012
\015\012Please rate this solution
Taking astab at this but your kit floor has been replaced and to close to counter now????, your either shimming up counter or removine the floor from under d/w
Repair Help & Product Troubleshooting for Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am installing a Kenmore dishwasher model 13743. I have direct wired the washer?s terminal box wires to the wall power via a BX wire and the washer doesn?t respond. None of the panel buttons are active. With a multimeter, I find that there is voltage on the wall wires and on the dishwasher end of the BX cable wires that hard wired to the wall current. Even though, when I connect the dishwasher?s terminal box wires to the BX wires as directed in the Installation Instructions (white to white,


Next step to check the door switch...the door must close and the switches on the door must close to send power to the control...let me know ... Dishwashers

How to install a gasket on a kenmore dishwasher. I have a Kenmore dishwasher and have put the gasket around the door but there's extra pieces on both ends and can't figure out where to attach them on the underside of the door.


... Kenmore Dishwashers

I just installed a Kenmore Elite Dishwasher. The Dishwasher will not run and is not responding toany commands. I checked the powersource and water supply to the Dishwasher and everything is working fine. We are confused and need some help toget this dishwasher working. It is brand new and just out of the box.


If there is an assembly manual, check it! There are sometimes hold downs and protective strips placed on the machine at the factory to prevent tampering. There is probably one that is stopping the power from reaching the control panel. It may even ... KitchenAid KUDD03STSS Stainless Steel 23 in. Built-in Dishwasher

I have a Kenmore Elite Ultra Dishwasher and the cleaning light is flashing. I have tried pressing the start/resume button and closing the door within 3 seconds. I am not able to turn on my dishwasher. I have tried turning off the power for 20 minutes but when power was restored the green light continues to flash and the dishwasher will not work. This machine was installed in May 2008. Help!


If the clean light flashes 7 times, pauses, then repeats...When\015\012the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non ... Dishwashers

No water is coming thru the water valve to fill the dishwasher. The water is turned on. I had a Kenmore portable dishwasher and we just converted it to a built-in. The electricity is on and the water line installed. When I turn on the dishwasher, it comes on ok but no water is coming into the machine.


Most probable cause a faulty intake solenoid. OK start simple and go from there.If your have power and light etc come on then we know you are good for power. I'll assume that is OK. If\012you are not getting any li ... Dishwashers

Installing a seal kit to kenmore dishwasher, model


... Kenmore 18 in. 14432 / 14439 Built-in Dishwasher

Kenmore Dishwasher installation


It sounds like you either replaced your floor or your counter tops/cabinets. \015\012\015\012Your 2 options are to:\015\012\015\012\015\012Remove the flooring, (i.e. tile) to the toe kick of the cabinet a ... Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

Cannot find a hard install side mount kit for a Kenmore dishwasher


... Kenmore Dishwashers

Moved Kenmore dishwasher to new house. Installed it. It will not start. Is there a reset switch? Model 587-1541590. Electrical installation checked OK. Water connection checked OK. Is there something I should do before I call for repair person to come


You say "electrical installation checked OK"...is the machine hard wired into a junction box or does it plug into an outlet?\015\012\015\012If in a wall socket the new house circut may be on a wall switch which is currently off. If it is ... Kenmore Dishwashers

Want to know how to install dishwasher Kenmore model 630.77942011 I have no manuel how to install


... Kenmore Dishwashers

Installation manual Would like installation information on a new Kenmore 587.1541 dishwasher


... Kenmore Dishwashers

Kenmore Elited Ultra Wash dishwasher Model No. 665.13859K601 The normal wash button is flashing. I pushed the cancel/drain button and it stayed on. I've turned off the circuit breaker and tried pushing some button sequences as recommended on the internet. I can't access the tech sheet because of they way the dishwasher was installed.


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Installing model 665 kenmore dishwasher with granit counter top.The side bracket we are trying to use need to be snap of at the line to get dishwasher to fit right.The problem is we cant get to the screw the side of the washer is in the way and no hole is in the side of the washer.Need a real fix.


... Dishwashers

We recently installed a Kenmore dishwasher, Mfr Model# 13943. We have used the dishwasher approximately six times since Thanksgiving. Each time, after the wash cycle is complete, when we open the door, water has collected on the interior of the door, and water remains standing on some of the washed dishes. Is this normal?


... Kenmore Dishwashers

I have a Kenmore dishwasher that was installed 2 years ago. (587.1514). It is taking longer and longer to wash dishes, sometimes 3-4 hours and it has a funny sound. Please help!


... Kenmore Dishwashers

My kenmore dishwasher 665.1302 just instaled has electric but cant get it started


... Kenmore Dishwashers

The power cord in my install kit for the Kenmore 1344 dishwasher, isnt color coded. The power cord is 3 leads of course but the manual says nothing about which lead to connect to the color coded wires coming from the DW. halp?


It does not matter what lead goes to the white or the black. You just need to make sure that you have the ground in the right place. If it is a flat cord then the center wire is the ground and if it really matters the lead on the right of the ground ... Kenmore Dishwashers

Installing kickplate... no instructions - Kenmore 13869 / 13864 / 13862 Dishwasher


... Kenmore 13869 / 13864 / 13862 Dishwasher

Just bought and had installed on 9/25/10, Kenmore Elite dishwasher model #665.13929K010. Start light on the front panel flashes, then runs through all lights and ends on the complete light which contnues to blink. It will not actually start the wash process at all. Before I call Sears to come out, what is the reset sequence for this model? Any other solutions you can think of?


... Dishwashers

I just installed a new Kenmore Elite dishwasher but the water does not completely drain out after the cycle is done!!!! There is about 1/2 inch of water remaining in the bottom.


It is supposed to be in the bottom.it keeps the seal wet if the seal dries out you will develop a leak around the motor ... Kenmore Dishwashers

I need an installation manual for Kenmore Elite dishwasher 665.13423K701. How can I download a free one?


... Dishwashers

Trying to install Kenmore dishwasher model 13744 in under cabinet space. How does it fasten into space?


How is Kenmore Model 13749 dishwasher installed? ... Kenmore 13742 / 13744 / 13749 Built-in Dishwasher

Trouble re-installing parts - Kenmore 16639 Built-in Dishwasher


... Kenmore 16639 Built-in Dishwasher

We just installed a new Kenmore Elite #13123K dishwasher. It has power and water but does not run. The lights light up and all but it does not seem to be getting any water.


Is the water inlet valve open? ... Kenmore 24 in. 15173 Stainless Steel Built-in Dishwasher

Kenmore Dishwasher model 363.16212100 installation manual


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1872 seconds