Having problems with your Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher ?

After the wash & dry is complete, the next time I try to use it, won't turn on. I tried cancel and that starts and finishes but can't get any thing else to work. I turned off the circuit breaker but have to wait 6-8 hours before turning back on. Once this is done the machines runs normal again. I have to repeat this process every time I want run. Any suggestions on what might be causing this???


Answers :

I have the same problem. The only temporary solution I have so far is \015\012to turn off the circuit breaker and wait between 10 & 30 minutes \015\012before resetting the breaker. The the dishwasher will work for one \015\012cycle.
Repair Help & Product Troubleshooting for Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

After the wash & dry is complete, the next time I try to use it, won't turn on. I tried cancel and that starts and finishes but can't get any thing else to work. I turned off the circuit breaker but have to wait 6-8 hours before turning back on. Once this is done the machines runs normal again. I have to repeat this process every time I want run. Any suggestions on what might be causing this???


I have the same problem. The only temporary solution I have so far is \015\012to turn off the circuit breaker and wait between 10 & 30 minutes \015\012before resetting the breaker. The the dishwasher will work for one \015\012cycle. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

I have a Whirlpool ADP 5777 WH dishwasher I need to know if I can reset the dish washer, it is the timer which is stuck, so you can change the dial on the left for the various washes, eco, etc. but the time of the wash does not change!! Stuck at 2 hours 47 minutes!! I have tried turning the machine off at the powerpoint and turning it back on but that has not fixed it


... Whirlpool Dishwashers

My dishwasher skips the final drain cycle. The lines are all clean and there is no clog. It drains just fine in the beginning of the wash cycle. Every time I do a load of dishes I have to run the full cycle, then leave the machine open for 3-4 hours and start the cycle again and listen for the drain at the beginning of the wash to drain the machine from the initial wash and stop the machine after it is done draining so it won't fill up again. Sometimes we have to unplug it and wait about an hour


... GE Nautilus 24" Built-in Dishwasher

Kuppersbusch IGV 645.0 built in dish washer has started to make its audable intermitent beep alarm, with start light flashing, have checked the (rubbish) instruction manual it suggests filters are blocked but they are not, turn it back on and it sounds as if its working but just keeps beeping, can you advise pleas?, The last time this happened I turned it off at the mains for three hours then turned it back on to find the alarm had cleared


... Kuppersbusch Dishwashers

I've tried to use this new machine 3 times. Each time it was never turned off until I pushed the cancel/drain button. Once I let it run for 2 hours before turning it off. This evening I tried the rinse only button and when I checked on it,it had switched to the normal wash cycle. Then I pushed the cancel/drain button.


If this is a new machine and it's under warranty, Have a technician come out and repair it as soon as possible. then fully test it's operation after he is done fixing it . It sounds to me as though it ... Whirlpool Gold GU2275XTV Builtin Dishwasher

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


The electronic control board is most likely the issue. I would replace the pab that controls the dishwasher functions. The control board controls the cycles and the wash time selection as well as the on/off function of the dishwasher. ... Dishwashers

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


Your touchpad is likely faulty. Sometimes called a control panel. You can get parts, manual, pictures, part numbers, and more at partselect.com or repairclinic.com ... Dishwashers

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

Elite 665.13933K010 The touch panel is inactive. There appears to be no power to it. It has done this before twice...the first time I bumped the top of the door and the lights came on and it worked. Second time, I took it out of the cabinet, turned it upside down and examined everything looking for a loose wire or blown fuse. When I put it back together it worked. Any idea what is happening?


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I just bought the Kenmore Ultra Wash Dishwasher model # 665.1389. It worked about 4 times then before the it finished it lost power while it was running. Now it won't turn back on at all. I done everything in the trouble shooting manual and nothing worked. It's not the circuit breaker either. Everything else on the same breaker works fine. What could it be?


... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

Hi I am in an emergency situation with an ikea whirlpool dishwasher. I have no idea what model it is since it's built in and I can't find the manual in my rental apartment. The machine works normally until the part where it's supposed to pump the water out after rinsing. At this point it starts to beep, once, and then 3 times. On and on and on. If I open it, there is water stagnated there. If I try to turn it off and back in, it will go through a whole new program and then I get the same problem


Can you feel the pump operate during the last wash cycles? if not either theres a bad pump motor or lack of power to the pump during that cycle,if this is ok,then remove the drain hose to the main drain to see if this is plugged up with food debris ... Whirlpool GU2400XTP Built-in Dishwasher

I have a brand new Blanco dishwasher but im unsure if it is a DWF6XP, DWF4X or DWIN7 model. It does not have a salt dispenser if that helps. Last night when running for the first time i had a plumbing issue where the drain pipe was not set high enough as it states it has to be 500 to 100cm of ground height. Also had a leaking sink drain pipe. Fixed all that and turned machine back on and it pumped all the water that was inside to drain. I have cancelled the program and restarted but now it is ru


Unplug it and wait 5 minutes. Plug it back in. This will reset the machine. Put it on full cycle and allow it to do a full cycle. It should work just fine. ... Dishwashers

My dishwasher will start any program, it drains, fills, empties & beeps continually within a few minutes. The rinse light stays on until the machine is turned off & re-set. Aditonally, the ater heating has been hit & miss for some time! A service guy cleaned the water sensor with hot water fro a ketle + tooth brush, but the problem came back after a couple of weeks. Having removed item he cleaned, it looks fine and appears to switch OK. Not sure if its actually faulty. Is the themperature sensor


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Hi My dishwasher started washing by itself and it kept going nonstop for a few hours, I stopped it and realized the panel did not light up , I shut it off and waited a while before turning back on again and this time started draining. I'm unable to use the panel to reprogram the dishwasher because it doesn't light up, do you have any solutions? please help


... Viking DFUD042 Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

I have a Braun combimax 650--it is fairly new. It was working fine last time I used it, but this time, the dial that turns the machine on seems to be stuck. The little button for the pulse does work. I read the instructions, which said that this might happen when the machine overheats and to wait fifteen minutes, but it is definitely not an overheating problem and the last time I used it was weeks ago.I love this machine and now need to use it for quite a number of things--any help you can provi


... Braun K-650 CombiMax Foofs Processor FOR 110 VOLTS

My De Dietrich dishwasher turns on but then turns off after a couple of minutes with no water entering dishwasher. I found some instructions and turned on and off 5 times (and unplugged). This worked once and full cycle ran but not the second time. Not sure if it is worth paying 165 call out charge or getting new machine as 7 years old


... De Dietrich 23 in. DVF110J Built-in Dishwasher

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

GSD2200G00WW. When starting washer, part of the time the machine will not start, other times if machine has been running for a while and you open the door and try to restart the machine it will not restart. You can hear the motor humming as if it wants to go but it will only restart if you turn the motor shaft even just a little. I am wondering if the electric motor is dying??


... GE GSD2200G Built-in Dishwasher

It does not matter which cycle is chosen, once "start" is pushed on our Asko D3120W the drain pump comes on empties the machine, then it fills for the first time, and turns off. It happens on all cycles. We have turned off the power thinking that would re-set the machine, but it has not worked. Do we need service or is there something we can do at home?


Hello &\015\012Welcome to FixYa\015\012\015\012The problem\015\012seems to be with the frozen main pump or the pump seal/impeller gone bad. To\015\012solve this the pump and motor has to be removed and then the part rep ... Asko 24 in. D3120 Dishwasher

The last time I used the pressure washer was running fine. A few minutes later I tried to start it up and could barely turn it over. I removed the recoil and could turn it a little easier backwards. The motor is a Honda GC190 on a karcher pressure washer and has 20 -30 hours of running time. Thanks Clint


... Karcher 2500 PSI Pressure Washer

Our Miele DW just keeps going through cycles constantly and will not shut off on its own. It has gone all day. When we turned the dial manually to "OFF", the water keeps filling until it overflows the machine onto the floor. So far, our only option has been to turn the machine back on and let it keep running. Any suggestions?


Hi,\015\012\015\012sounds like a faulty electronic unit as i have seen this before where the unit continously fills with water. \015\012you will probably need a service call to repair the unit unless you are happy to fix it yourselv ... Miele 24 in. G865 Built-in Dishwasher

Our dishwasher won't start (model number 665.16049401). We had a similar problem last summer and a repairman came and fixed it. The problem was that the water level had gotten too low and so the machine locked itself off. This made sense as, at the time, I remembered filling the pool, running laundry and someone taking a shower all at the same time that I turned the dishwasher on. I am guessing this is the same thing that has happened now. The repairman put in a code and the machine worked. Can


Hello,\015\012\015\012ahhhh, you're taking about the reset sequence.\015\012okey dokie :)\015\012\015\012Here it is:\015\012Push the NORMAL WASH then HEATED DRY buttons in that sequence two to three t ... Kenmore Dishwashers

Maytag Dishwasher I need the reset sequence for my dishwasher. The power comany had turned off the electric to the house to make chages elsewhere in my house. When the electric was turned back on all appliance came back on except the dishwasher. The dishwasher has a front panel touch pad and three of the panel lights are flashing. I know there has to be a sequence to reset the machine. I also need the peace and quiet in the house since I am the husband and am suppose to know it al


We have a model mdvtt53aww1 and you can push three buttons and will light up the hi temp wash, heated dry and sanitize is there a code make it start ... Dishwashers

Good morning. I have a KitchenAid KUDM01TJ with a constantly flashing "Rinse" light. when I hit the "Cancel" button, it too flashes in the same time with the Rinse light. I left the machine alone, came back a few days later and saw that the issue had resolved itself - but I didn't use the machine. A few days later, the "Rinse" light was flashing again and naturally, I hit "Cancel" to see if the same thing happened and it did. This time the lamps are still flashing. I read through the other repo


No its not the problem of button secquence.its the problem of keypad circuit this is creating this problem.as the circuit is getting overheated and it stops working.the key pad sometimes functions and sometiomes doesnot.in this case the key pad circ ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1256 seconds