Having problems with your Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher ?

Dishwasher does not start, on any cycle selection. the only button that works is the cancel button which tells me the unit has power. this has happened before and a service tech was called and it "magically" started after he pushed the cancel button, not so this time??


Answers :

Make sure the floor is dry where you are standing.
\015\012
\015\012Push the cancel button twice in quick succession to attempt to turn the washer off.
\015\012
\015\012Open the door all the way and look over the inside of the dishwasher. You will be looking for obstacles that keep the arms from turning/ objects in the bottom of the dishwasher/ a break in the seal, etc. Is there any standing water in the dishwasher?Check the drain. If you have a filter, open it up and check it for debris. Be careful what you touch to avoid hot surfaces inside the dishwasher.
\015\012
\015\012Sometimes, opening the door all the way, and leaving it for a few minutes will reset the dishwasher. Don't give up try this a few times.Be patient, though and wait a while between each try. Avoid pushing buttons other than the cancel button until you are sure that the dishwasher has been reset.
\015\012
\015\012Do you know whether your dishwasher is hardwired or if there is an outlet either on the wall behind your cabinets or hanging behind your cabinet or counter where it is actually plugged in. If you find that it is actually plugged into an outlet you can unplug it, wait a few minutes for it to reset, then plug it back in. If it is hardwired do not attempt to do anything with the wiring. If it is on a separate circuit, and you are knowledge about your power box, you can actually turn the circuit breaker to the DW off, wait a few minutes and turn it back on.If you are not knowledgeable about this you may have a friend who is. Again, be sure you are standing in a dry place, and that you are dry and not wet from working on the dishwasher.
\015\012
\015\012If you cannot find any reason inside the washer that is stopping it from operating and you cannot reset it, you will need a service call, or if you explain the circumstances of your past call to them, they may have suggestions for your particular model to reset it.
\015\012
\015\012Good luck to you. I know this can be frustrating. I have had a similar problem in the past.
Repair Help & Product Troubleshooting for Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher does not start, on any cycle selection. the only button that works is the cancel button which tells me the unit has power. this has happened before and a service tech was called and it "magically" started after he pushed the cancel button, not so this time??


Make sure the floor is dry where you are standing. \015\012 \015\012Push the cancel button twice in quick succession to attempt to turn the washer off.\015\012 \015\012Open the door all the way and look over t ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

I own a Maytag MDB5100AWB three lights are flashing on the panel, the clean button, rinse only and heavy wash. I've tried turning off the breaker for 20 minutes, pushing the buttons in sequence, holding them down, nothing seems to work. It's done this before and a repairman pushed the buttons and it worked. Is there anything I can do to avoid another service call?


... Dishwashers

The clean light keeps blinking and the dishwasher will not start. I pushed the cancel button and it runs for about 30 seconds and just shuts off. Nothing happens when you push the start button.


HiIf clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If ... KitchenAid Dishwashers

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Hi I have a bosch diswahser smu 7000. No power when I push button. Manual says its could either be fuse or circuit breaker. Checked breaker its ok. My manual does not say anything about location fuse. Called bosch. And they said they cant tell me. I nee to have a service call. Any help. Thanks.


... Dishwashers

I have a 1 year old maytag dishwasher and it has the touch buttons on top of the door . When you touch the buttons to turn it on, nothing happens. It will light up the type of wash you want e.g. heavy,light...., but it won't start when pressed. It will cancel when pushed, but can't get it to start. HELP!!!


... Maytag Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

My GU2475XTVY0 built-in dishwasher has the "Normal" light flushing since yesterday morning. We pressed "Cancel" button, other buttons, and finally turned the power off and on, but it didn't do anything. Do we need to call for a service? It's less than 1 year old. Thank you!


Whrilpool Gu3600XTSB1 \015\012\015\012After a power surge the control panel pot scrubber and\015\012normal lights were flashing. I replaced the circuit board, thermal fuse and\015\012control panel. However, the lights are still flashing. what i ... Whirlpool GU2400XTP Built-in Dishwasher

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

I recently replaced the chopper in my whirlpool quiet partner III. now it won't drain. I can push the cancel drain button and hear the pump running, but nothing happens. I tried reversing the wires to see if I had switched them around when I was trying to figure out why it wasn't cleaning the dishes and that didn't work either. I checked the hose for cloggs and nothing. I am left scratching my head. model # gu1200xtkt0


It sounds like you've done a lot to try and fix your dishwasher. Make sure your air gap is not plugged up and double check the drain hose. If those are clear change out your drain hose. Part#8270145 the elbow connector sometimes have a bad chec ... Whirlpool GU2400XTP Built-in Dishwasher

Kitchen Aid model KUDS01FLSS3, water gets pumped into bottom of dishwasher but when the cycle needs to change to shoot the water over the dishes nothing happens. When the cancel button is pushed all the water will drain.I have cleaned out the bottom drain compartment that was jammed with calcium build up and guck. Would this be a pump /motor problem or electrical circuit board problem?


... KitchenAid Dishwashers

My Maytag dishwasher will not start. I have a concealed touch pad on top. This is the third time it has done this. Every light works but the start button. If I wait a day or two it will start working again. I have arranged a service call twice and had to cancel both times because it was working. HELP


... Maytag 24 in. MDB8951AWS Stainless Steel Built-in Dishwasher

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Bosch dishwasher has standing water doesnt drain out, repair man pushed 2 buttons cancel drain and it drained last month, but happened again today and it wont work for me


Fixed mine very easily... After checking and cleaning the filters by the tub's drain, I checked the air vent atop the sink -- it had a small bit of gunk trapped in the outlet. Cleaned it out, ran a "rinse & hold" cycle and it drained the tub beautif ... Bosch Dishwashers

My Haier dishwasher ESD300 constantly runs and tries to pump out water that isn't there and nothing happens when I push wash cycle or cancel buttons. Does anyone have any suggestions?


... Haier Dishwashers

I have a Kitchen aide dishwasher Model KUDI01ILWH6 that will not turn on..there is a control lock light on and I have tried pushing the cancel button but all that happens is the control lock light flashes 3 times and the dishwasher still wont turn on....Please , how to I disengage the control lock


... KitchenAid Dishwashers

Kitchen Aid model KUDS01FLSS3, water gets pumped into bottom of dishwasher but when the cycle needs to change to shoot the water over the dishes nothing happens. When the cancel button is pushed all the water will drain.I have cleaned out the bottom drain compartment that was jammed with calcium build up and guck. Would this be a pump /motor problem or electrical circuit board problem?


... KitchenAid Dishwashers

Kenmore dishwasher Mod 665 13852K601. MANUAL WASH and CANCEL lights are blinking simultaneously. I unplugged washer and plugged back in. Same thing. Nothing happens when any button is pushed. What's going on?


... Kenmore Dishwashers

DU1055XTPQ3 built in Dishwasher... panel has power "cancel" button when pushed you can hear the pump running but on wash the light blinks about 3 times and goes out, nothing happens. Is there a sensor or something in the panel that needs replaced? Jim


Hi\015\012\015\012First try resetting the dishwasher by pressing the AIR DRY button and hold it for 15 seconds. After this if it blinks again 3 times then the control needs replacement. Hope this helps...please post back for further assistance. ... Whirlpool Dishwashers

When I push the start button nothing happens, all the other buttons work


... Whirlpool MDBH979AWB Builtin Dishwasher

Kenmore Elite Dishwasher, Model 665.15979992 No Heat Dry Button/Light: The dishwasher will not work. Have tried to no avail the various alternatives listed in this thread and others. Here's what the dishwasher is doing: To start off, the red light on the "No Heat/Dry" button is on - sometimes it's on steady; other times it blinks depending on whether other buttons have been pushed. Pushing any other button also causes the "Lock On" red light to come on. Pushing the "Cancel" button causes all


Have you checked the thermal cutoff switch located inside the door by doing a continuity test to it if this is sounding like where your problem are is coming from on this diagram ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a Whirlpool GU1100 built-in diswasher that will not clear the pot & pans selection. It is stuck with the pots & pans and the cancel buttons lit and blinking. It will not start or clear. I have tryed to shut the power off for awhile and this has not helped. Other buttons can be pushed and will light but the other two remain blinking. If the clear button is pushed it will clear the other button but not the pots & pans or itself. Is this a problem I can fix myself?


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0965 seconds