Having problems with your Whirlpool 24 in. GU2500 XTP Built-in Dishwasher ?

Water isn't draining

\015 There is a small amount of water sitting at the drain when washing is finished\015

Answers :

Check all the possible causes below to address this issue you are having. replace any part or device if found to be faulty


1. Air gap / Drain hoses
If there is an air gap (located in\015\012the sink, near the faucet), check to see if it is clogged. Unscrew the\015\012top cap and see if there is anything blocking inside. Note: If there is\015\012no air gap installed, the dishwasher might not drain properly.
\015\012\011\011\011
\015\012If the drain hose is clogged, the dishwasher would not drain. If there\015\012is an air gap installed, it is very common that a hose going from the\015\012air gap into the garbage disposer is clogged. Remove and clean the\015\012hose. Make sure to reattach the hose before starting the dishwasher.
\015\012\011\011\011
\015\012\011\011\011Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.
\015\012\011\011\011
\015\012\011\011\0112. Broken belt
\015\012\011\011\011Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.
\015\012\011\011\011
\015\012Note: Sometimes the belt would just come off the pump. Even though it\015\012might not be broken, it is recommended that you replace the belt,\015\012because it is probably too stretched out.
\015\012\011\011\011
\015\012\011\011\0113. Pump
\015\012Some models have two impellers inside the pump - one, wash impeller,\015\012takes care of the wash cycles, the other, drain impeller, drains the\015\012water out. If the drain impeller is broken (broken blades, shaft), the\015\012dishwasher would not drain. Replace any broken pump components.
\015\012\011\011\011
\015\012\011\011\0114. Drain solenoid
\015\012Some models (for example most GE dishwashers) use a drain solenoid to\015\012drain water out. Sometimes the solenoid gets stuck, preventing the\015\012water from draining out. Try to free up the solenoid. If unsuccessful,\015\012you might have to replace the pump assembly.
\015\012\011\011\011
\015\012\011\011\0115. Motor
\015\012\011\011\011If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.
\015\012\011\011\011
\015\012\011\011\011Replace the motor if defective.
\015\012\011\011\011
\015\012\011\011\0116. Timer
\015\012\011\011\011Replace if defective (note: uncommon problem).
Repair Help & Product Troubleshooting for Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My garbage disposal badger 1 was just replaced with the same badger 1 disposal. my dishwasher will not drain water anymore. the old one had a hole where the attachment to the dishwasher hose goes but ther isnt one for the new 1 but the hook up is there. Do i have to drill a hole in the new 1 for the water to drain out


I THINK NO :\015\012 THE DRAN PATH MAYBE BLOCKED\015\012 ALL YOU DO 1ST TO SURE THE PLUMPING IS OK OUT SIDE THE M/C\015\012 THEN IF IS OK BE SURE FILTERS INSIDE M/C AFTER YOU OPEN THE DOOR OF M/C PERIODICLY CLEAN AFTER E ... Dishwashers

When the washer drains it comes out of the, what i thought was just the vent, on top of the sink next to the fouset knob. isnt the water supposed to drain into the existing drain for the garbage dissposal under the sink. we just bought this house with this problem. not sure of the model but figured that the drain would be the same concept.


... Kenmore 16529 Built-in Dishwasher

The dishwasher isnt draining the water away after the wash cycle ,and the water is leaking trought the bottom of the machine, its model is beko dishwasher dwd 4310s


Need make and model they are very model specific. ... Dishwashers

Haier dishwasher Hi my Haier dishwasher is flashing 3 of the 4 leds and beeping 10 times while the suction pump drains the filter then will not start. Can you tell me what this fault is? water pressure OK ,drain isnt blocked,none of the buttons have any effect. Any info would be helpful thanks.


I useto have same problem. For some reason there was water under machine, then i tilted machine, clean water and problem solved. This is built-in dishwasher that is why water acumulates under machine and "leak cut off switch" turn off machine. You ca ... Haier ESD200 Built-in Dishwasher

I have a hotpoint hydrocare de luxe 7843 model it isnt plugged into the mains or any water flowing through it but when i was filling up the salt container some water split out and drained away and then leaked from the bottom just by the connection for the waste pipe


... Dishwashers

It isnt draining water. checked waist pipe and it isnt blocked Looks like the problem is in the machine. regards Brian


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Dishwashers

Water isnt draining


Check your drain line and/or drain pump. The drain line should have a high loop at the point prior to where it connects to your drainage system in order to prevent drain water from the kitchen sink from back flowing into the dishwasher. In addition ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Belling IDW604 Error E4 coming on machine, I have drained all the water from the machine and switched it off and back on again at the wall and it still isnt working. Can you please help????????


I found the solution myself. Underneath the machine, there is a plate. \015\012On the plate, there is a float and a\015\012 microswitch, when the water leaks onto the bottom plate it raises the \015\012float and activates the microswith which shuts d ... Belling 24 in. IDW603 Built-in Dishwasher

Magic Chef DU4K is not draining all the water. There's at least a gallon of water standing in the bottom. I have cleaned the air gap assembly and drain line completely. They were even sanitized in hot water. I do not hear the water draining like it use to. When it worked properly you could always hear water draining into the GD. Now I can hear any draining. Again, there is no clogging anywhere in the drain line assembly. Is it a bad pump. I don't know where to go next with this.


... Magic Chef Dishwashers

There is gum stuck somewhere in my dishwasher drain line. The water won't go down. I took the inside apart and can see the hole where the drain water goes. I disconnected the drain hose under the sink. I got the water to drain out when there was alot in there, but now it won't drain again. I blew compressed air from a compressor backwards through the hose and it makes a big splash and bubbles inside the dishwasher, but the water still won't go down. I put Boiling hot water and vinager in there t


Ther e is noo easy fix, short of replacing the drain line( if indeed thats where the clog is)although you checked the hose from the under the sink, did you check with in the hole where the sink conection is made??and try disconnecting the drain hose ... Dishwashers

I have a Bosch Diswasher that is not draining. I have disconnected power for 35 minustes and used shop vac to excess water out of drain line. i also pulled all water thru the drain line from the tub itself. i assume that because i could pull the water, all baffles and lines are clear as i emptied the tub from drain line. you can hear the pump come on to drain water but no water is moving. What would be my next step. If it is to replace the pump, how do i easiest access the pump to remove and rep


Either the selector switch or pump is faulty. If there is not any clogs anyways. The system may need to be reset. Most resets are done by entering a series of numbers on the touch pad to enter diagnostic/test mode where the machine can be reset. This ... Dishwashers

I have a DU8000XX6 series Kenmore dishwasher that won't drain the water properly. There is about a half inch of water in the tub and the float is raised (not sitting on tub bottom). When I lift up the float a little more I can hear the float switch make. I would assume that when the water is high enough the float switch makes and energizes a solenoid valve in the drain to drain the water, but shouldn't it stay open until all the water drains? Lifting the float while the dishwasher is off wo


... Kenmore 24 in. 15142 Built-in Dishwasher

Our kitchen drain clogged recently and water drained back into our VUD141 dishwasher. A plumber cleared the drain, and turned on the DW - which pumped out the standing water. But now, we have no water flowing into the dishwasher. The drain pumps, the heater works, but there's no water supply. The plumber who cleared the drain said he didn't DO dishwashers, and I cannot locate the owner's manual since we prepared for a move.


Hi\015\012\015\012 \015\012\015\012When the dishwasher won't fill and the water supply is on,\015\012then the issue is with the water inlet valve which is either clogged or\015\012blocked, you can try to clean it. If this wont so ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

My WHirlpool dishwasher won't drain - basin is full of water. Machine starts and runs the drain cycle, but something is clogged. I opened up the bottom, and pulled off the drain hose to the disposal, and that had no water in it, so the clog is somewhere before the water gets to the hose. If I run the dishwasher drain cycle, it is not pumping water into the hose. What next?


The clog could be in the hose,or on up in the mouth of the drain,air pressure might dislodge the clog,or dissasible of the drain pan in the machine. ... Dishwashers

KitchenAid dishwasher KUDS24SEBL does not drain after rinse. It goes through wash cycle, drains water completely , then it fills water for rinsing, runs and after that it does not drain. Cancel does not work after that. Water is very hot inside the tuba t that time. The dishwasher needs to be left for an hour or so before the cancel button can drain the water out.


... LG LDF6810 Built-in Dishwasher

Kenmore elite dishwasher model 665.13153k701 At end of wash cycle, water does not drain completely. Intemediate drains during wash do drain completely. rinse and hold drains completely. watching water at end of wash thru disposal, water flow cuts off like valve closed. other drains taper off


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My asko d3250 thinks the drain hose is blocked. but when i pour water in the dishwasher to see if the water is being drained, the dishwasher is draining properly. Yet the dishwasher after it has drained the water, will shutoff and start flashing the Large Pot icon (drain hose is blocked error code). Is there a sensor that is faulty?


Yes, it sounds like it is to me. I'm not able to pull your model up on my data base,if I could I would be able to tell you where it is located. I would assume that it's located either inside the pump or close to it. Sorry I couldn't be more help. ... Asko Dishwashers

My dishwasher DW60 does not complete the program and drain the hotwater leaving hot water in the bottom of the dishwasher however when I run a prewash cold water cycle the water does drain away and the dishwasher program works correctly do you know why it drains cold water okay but not hot water


... Dishwashers

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

We recently bought a house with a Kenmore 363.16222100 (?) dishwasher. No manual. Monday night it didn't drain properly and leaked some water on the kitchen floor. The cycle had finished when we saw the water on the floor. We bailed out the excess water. I took off the drain cover and insert. I couldn't see an obvious clog problem, but cleaned it out. Then I tried a short cycle, interrupting it to shorten it. No problem. Water seemed to drain fine. I did find a part that looked like a straw and


HelloWelcome to FixyaMy name is Huum,You can find your model dishwashers manual here at this site. this sitehttp://www.managemyhome.com/mmh/lis_pdf/OWNM/L0801624.pdfI feel you should not invest blindly in someone ... Dishwashers

Whirlpool dishwasher ADG 7460 will fill with water ok and wash but will stop before it finishes the cycle leaving water in the machine. if you set it to rinse it will drain the water .... so the drain pump is working ..... water it drains is hot so the element seem ok ..... help


Hello & Welcome to FixYa Dishwasher not draining completely problem usually ... Dishwashers

I have a Bosch Exxcel dishwasher which runs the drain pump constantly even with the door open and despite there being now water in the machine at the cycle wont start. I have checked the warer amtrix and the ffed hose to the sump for blockages. The float switch operates OK but when the water drains down the float drops and the water is pumped in, then the float rises and water leaks out and the drain pump kicks in again and no more ater will come in unless you push the float down. Inside the bas


I am not sure about this model but most models run a drain cycle for a set period at the start of a wash cycle and then move on to normal filling and cycle of machine provided the various switches are at the low level it will carry on to its set cycl ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1322 seconds