Having problems with your Whirlpool 24 in. GU2500 XTP Built-in Dishwasher ?

Cycle buttons work, option buttons dont, Cant deselect heated dry, Wont start

\015 Dishwasher is 2 years old. When I select a cycle, normal,accusense,light,pots & pans etc. these buttons work as far as changing the light above the selection. However the heated dry button stays lit all the time(cannot deselect it) nor will start/resume or cancel drain do anything either. After the cycle selection is on for a couple minutes everything goes blank.I can select normal again and heated dry lights up but it will not start. I have cheched the door latch switch to be good. What next? Thanks.\015

Answers :

I had the same symptoms and the front panel was the fix
the part with the buttons on it
The part is covered by warranty. However, the labor is not and Whirlpool will not replace the part without having someone service the unit. Every place I checked wanted $100 just to come out and tell me what was wrong. Any service would be extra. Seems like Whirlpool figured out how not to stand behind its products. They should be held accountable.
Repair Help & Product Troubleshooting for Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cycle buttons work, option buttons dont, Cant deselect heated dry, Wont start


I had the same symptoms and the front panel was the fixthe part with the buttons on it ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

I have a Whirlpool model DU1055KJVQ1, Type 575-0 under-counter dishwasher which is less than 2 years old. In the last couple of weeks, it wouldn't start intermittently, and I would need to hit cancel on the keypad, and then restart. Now that doesn't work. When I try and start the dishwasher, it doesn't work. I press Normal for the cycle, heated dry for the Option, and then hit Start. The buttons light up for 20 seconds or so, nothing happens and then they go out. Any ideas?


... Whirlpool Dishwashers

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Describe your whirlpool du948pwpq Problem: I have a whirlpool du948pwpq dishwasher in a tenant's unit. They said the delay start button is no longer working. Also, they cannot "de-select" the heated dry option. It seems to be an issue with the electronics of the control panel. I've already tried to "unlock" the buttons - no change. I also powered off the unit in hopes of re-setting - no change. Does anyone have any other suggestions? I am hesitant to call a service person (it's out of warrant


... Whirlpool 24 in. DU948PWPQ Built-in Dishwasher

Kenmore undercounter dishwasher model 66517019400 wont start..I want to purchase a new control board do you think this is the problem? normal cycle light comes on, cancel button works, heat on button works, just wont start ??


It might not start because the water solenoid is failed, or the water level sensor is failed.\015\012\015\012You have to use a meter to test these components first. Put your voltmeter on the two leads going to the water solenoid, and psuh ... Kenmore Dishwashers

Rick ead i dont know the reset combition for my dish washer it has 10 buttons auto clean. heavy. normal. light. rinse only. options steam. hi temp. heat dry. sanitz and delay time. + start and cancel its two years old. can you tell me how thanks.


... Maytag Dishwashers

I opened the door before the drying cycle finished. I pressed the cancel button, then I pressed "normal wash" and the "start" button and it didn;t start. Then did "cancel" again . I pressed the "heat" button for five seconds to lock the door so I wouldn;t make the same mistake again. It still won't start. Now the "cancel" button won't work and the start button flashes. What do I do now?


HI. The unit will need to be reset. This is achieved by unplugging the unit for five minutes. If unplugging is not an option, simply,shut down the appropriate circuit breaker for five minutes. This action will, essentially, reset the logic sector. On ... Dishwashers

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

Kenmore Ultra Wash Model 665 - 158* Front panel not working properly. Pressing Normal does not light that option. The only option that lights is "Quick Rinse", pressing this lights that option and also the "No Heat Dry" light. After a few seconds the lock light comes on. Looks to me that the "No Dry Heat" button is stuck on, which causes all the other things to happen Is there a way to fix this?


... Dishwashers

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

My dishwasher won't start. The Heat Dry button is lit up and the Washing light is blinking. Some websites recommended holding down the Heat Dry button for 5-7 seconds, but that didn't work for me.


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have the Quiet Partner II, DU1100XTPB7, and have already replaced the electrical ciruit board but having the same problem. When I hit any wash cycle button, the soak/scour & heated dry buttons light up, but will not "start." The "rinse only" button does nothing, but if I hit the "delay" button, then the soak/scour, cancel, and also the status buttons, washing & drying, all night up at once. The only button that seems to be working is the "cancel/drain." Although there's no water in the mac


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Wont start Won"t start. Some program lights work, then shut off within a few minutes. Example: The SmartWash, Heated Dry, and Start lights will work, then go out. The NormalWash light will not work


We walked away from it for about an hour, came back, reset it, and it started. Thank you. ... Kenmore 24 in. 16022 Built-in Dishwasher

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

Pdw 9200 jo3ww dishwasher- The start button doesn't work. The arrow keys work and the heated dry button works. I tried turning the power off for 30 seconds and it still doesn't work any ideas?


... GE PDW9200N Built-in Dishwasher

Pushing settings and start button but will not start. The green light comes on for the setting and the Heat Dry but once start is pressed it will not start and after 30 seconds the lights go off. Also, Smart Wash button no longer works


... Kenmore 13743 Staimless Steel Built-in Dishwasher

Dishwasher wont let u select a cycle...all buttons seem locked...ive unplugged it for 5 seconds or so and then plugged it back in and the normal wash button light comes on and the heated dry button light comes on, but it wont start and it doesnt respond when buttons are pushed...please help. thanks


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

I have a Whirlpool Gold Quiet Partner III (Model GU1200XTKB0). I have used it previously on "Normal" cycle and I always keep it on Air Dry. Last night I used the "Pots and Pans" cycle and it seemed to work fine. But this morning the Air Dry light is flashing and if I press a cycle key the Rinse Only light starts to flash as well. Nothing works. I have made sure that the console is not locked. Any suggestions? I do not have a Heated Dry button, only Air Dry. Thank you.


... Dishwashers

The start botton does not work when you push the sanitize, heat dry, and heater they light up once got it to start by pushing the stop button 3 or 4 timesand then the start button. but not any more. Any thing other than replacing the whole control under the cover sheet available? ?


... Whirlpool MDBH979AWS Builtin Dishwasher

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Kenmore model # 587.15103801 - I select wash cycle , heat dry button and select start all buttons i selected flash and machine wont start wash?


... Dishwashers

I purchased a second hand Electrolux Dishlex DX403 with a kitchen. The dishwasher turns on when I turn the powerpoint on and makes a noise as if it is about to start. I attempt to press the buttons to set a mode and start it and it wont work, the buttons dont do anything. How can I fix this?


... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have and kenmore model # 66517779990 were the lock light is on and the control buttons won't work or start the the dishwasher the manuel says to hold the dry with not heat button for 4 seconds and that will reset it i tried that but it did not work


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1922 seconds